• 대한치과교정학회지
• /
• 제22권3호
• /
• pp.647-656
• /
• 1992

The purpose of this study was to evaluate the elastic memory process in cold worked stainless steel wire and the effect of heat treatment on it. 0.018 inch round and $0.019\times0.025$ inch rectangular wire (ORMCO stainless wire) were used in this study. Each wire type had 4 groups: non-heat treatment group, furnace heat treatment group, electric current heat treatment group, and bending after heat treatment group. Each group was consisted of 10 specimens. With the Jig, each wire was bent into v-shape uniformly, and width of two free ends of each v-shaped wire was measured by caliper (to the point of 0.1 mm correctly) at time interval of offjig, after heat treatment, 1, 2, 3, 4 hours, 1, 2, 3, 4, 5, 6 days, 1, 2, 3, 4 weeks after. The results were as follows: 1. In non-heat treatment group and bending after heat treatment group, elastic memory process was occured $60\%$ within 1 hour, and more than $90\%$ within 1 week. 2. In furnace and electric current heat treatment group, almost all elastic memory process was occured during teat treatment, and then specimen was stabilized dimensionally. 3. Magnitude of deformation by elastic memory was greater in heat treatment group than non heat treatment group and bending after heat treatment group. 4. There was no remarkable difference in deformation pattern between 0.018 inch round wire and $0.019\times0.025$ inch rectangular wire.

• 한국해양공학회지
• /
• 제20권1호
• /
• pp.1-6
• /
• 2006

The effects of microstructure on the damping capacity and tensile properties of 316L stainless steel were investigated. Increasing the degree of cold working, the volume fraction of $\varepsilon-martensite$ decreased after rising to maximum value at specific level of cold working, the volume fraction of d-martensite slowly increased and then dramatically increased from the point of decreasing $\varepsilon-martensite$ volume fraction. Increasing the degree of cold working, the behnvior of damping capacity is similar to that of the $\varepsilon-martensite$. After the damping capacity showing the maximum value at about $20\%$ of cold rolling, damping capacity was decreased with the volume fraction of $\varepsilon-martensite$. Tensile strength was proportional to the volume fraction of d-martensite, and elongation steeply decreased in the range low volume fraction of a'-martensite, then slowly decreased in range the above $10\%$ volume fraction of d-martensite. The damping capacity and elongation is strongly controlled by the volume fraction of $\varepsilon$ martensite with liner relationship. However, the effect of the volume fraction of d-martensite and austenite phase on the damping capacity was not observed. Tensile strength was governed by the volume fraction of d-martensite.

• 한국강구조학회 논문집
• /
• 제24권4호
• /
• pp.443-450
• /
• 2012

이 연구에서는 내진구조용 강재(SN)의 냉강롤성형된 각형강관을 사용한 CFT 부재의 중심축하중에 대한 구조성능을 평가한다. 일반적으로 냉간롤성형 및 냉간프레스형성으로 인하여 각형강관의 코너부와 평판부 모두 SN강재에 비해 재질변화가 발생하며, 항복강도와 인장강도 및 항복비의 상한치가 높아지는 경향을 나타낸다. 이러한 현상은 강관의 국부좌굴 이후의 비선형거동에 의해 영향을 주며, 이는 CFT 합성 부재와 같이 비선형해석모델에 대하여 영향을 미친다. 따라서 각형강관의 가공열화도를 평가하기 위하여 각형강관의 재료시험을 수행하였고, 세장비 및 판-폭두께비를 실험변수로 하여 일축 압축력을 받는 CFT부재의 구조성능을 평가하였다.

• 자원리싸이클링
• /
• 제9권2호
• /
• pp.46-52
• /
• 2000

사용한 알루미늄 캔을 다시 캔으로 재활용 하는 단계는 폐캔의 수집, 폐쇄, 선별, 도료제거, 용해 및 2차지금을 제작하는 단계와 이 2차지금을 이용하여 열처리, 열간 및 냉간압연, 중간소둔처리 등을 거쳐 다시 캔을 성형하는 단계로 나눌수 있다. 본 연구에서는 2차지금에서 켄성형까지의 과정에서 중요한 요소인 미세조직 및 열간압연후의 집합조직에 미치는 합금원소의 영향을 조사하였다. 폐캔을 이용하여 다시 캔을 제조하기 위한 판재가공에서는 주조시 형성된 공석상들의 구형화와 $\alpha$상 ($Al_{12}(Fe, Mn)_3Si)$)으로의 상변화 제어가 필요한데, 열처리에 의한 석출거동을 조사하여 $615^{\circ}C$, 5시간 균질화 처리조건에서 최적의 미세조직을 얻을 수 있었다. 2차자금을 이용하여 캔소재를 제조한 결과, Mn량이 증가할수록 고용효과에 의해 전기전도도는 감소하고 집합조직의 발달이 억제되었다. Si 과 Fe는 금속간화합물 형태로 존재하며, 함량이 증가할수록 석출효과에 의해 전기전도도가 증가하고 변형집합조직의 발달이 촉진되었다. 캔은 냉간압연후 다른처리 없이 바로 제조되기 때문에 집합조직의 제어는 열간압연 및 소둔처리 단계에서 제어되어야 한다.

• 오토저널
• /
• 제16권2호
• /
• pp.12-21
• /
• 1994

본 연구에서는 차체용 알루미늄 합금 판재의 제조기술 개발을 위하여 선진국에서 사용하고 있는 알루미늄 합금 판재의 기계적 특성을 평가하여 이를 토대로 자동차 차체용 알루미늄 합금 설계 및 판재제조 기술을 개발하고자 한다. 자동차 차체용의 고 Mg계 알루미늄 합금의 양산 제조기술을 개발하기 위하여 Al-7% Mg 합금을 DC주조한 후 열간, 냉간압연 및 열처리 후의 특성을 평가하고 수입소재와 비교하여 실험하였다. 그 결과 자동차 차체용의 고 Mg계 알루미늄 합금 판재개발의 가능성을 확인하였으나 향후 광폭 판재를 제조하기 위해서는 대형 Slab 주조방안, 압연시의 가공성 향상등 판재 제조기술은 물론 성형성, 용접성 및 표면 처리성 등 응용기술에 대한 연구도 활발히 진행되어야 할 것으로 사료된다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2013년도 춘계학술대회 논문집
• /
• pp.125-125
• /
• 2013

기계부품 및 자동차부품 등의 내마모나 내피로성의 향상을 위한 표면처리로서 고주파처리, 침탄처리, 질화처리 등이 사용되고 있다. 최근에는 변형을 최소화 함으로써 후가공을 생략할 수 있는 질화처리가 주목받고 있다. 질화처리종류로는 염욕질화나 가스질화법이 사용되고 있으나, 이들에 비해 환경오염 및 공해가 적고 인체에 무해한 플라즈마 연질화법이 사용되고 있다. 플라즈마 연질화 기술은 IT기기의 제품에 적용되는 표면경화의 공정개발은 미비한 실정이다. 마이크로 구동 요소 부품중의 하나인 Leadscrew는 이송장치를 구성하는 핵심 부품으로 IT기기의 정밀 이송 및 구동제어에 사용되는 핵심 부품으로 사용되고 있으며, 리드스크류의 소재인 SWCH1018A(냉간압조용강선)은 표면 경도가 낮고 변형이 쉽기 때문에 표면 경화를 위한 플라즈마 연질화 기술을 이용하고자 했다. 본 연구는 플라즈마 연질화 공정을 적용한 시편의 표면경도를 높혀주고 변형을 최소화 할 수 있는 공정을 확인하는 것이다. 공정변수를 변화 시키면서 얻어진 시편의 표면미세 구조를 미소경도측정, XRD, SEM분석을 통하여 확인하였으며, 이를 통해 시편 표면경도를 높여주는 공정 조건을 도출하였다.

• 한국공작기계학회논문집
• /
• 제10권1호
• /
• pp.71-77
• /
• 2001

Experimental study if die-sinking electrical discharge machining(EDM) was conducted with rotating electrode system including inside hole for increasing the material removal rate(MRR). With the help of dielectric fluid flow through the inside according to the different internal diameter of the hole, the molten workpiece debris could be removed and flushed out during the EDM, Cold die alloy(SKD-1) was executed for different peak current and duty factor. From this study, the MRR was found to be increased with the peak current. The more MRR was obtained for the case of electrode inside diam-eter of 10 mm, but the MRR was decreased as the diameter near at the 4mm and 6mm. The values of surface roughness and roundness were analyzed under various conditions, and these were affected by the inside diameter change of electrode.

• 한국표면공학회지
• /
• 제35권5호
• /
• pp.279-288
• /
• 2002

Zinc phosphating for cold forming of steel was studied with emphasis on decreasing phosphating temperature. To lower phosphating temperature, some techniques, such as adding Cu ion into bath, using activator in the form of pre-dip, and aeration in bath, instead of using conventional accelerator, namely oxidizing agent, have been tried. It was revealed that phosphating, leading to coatings of Improved uniformity and fine crystal size, can be carried out using above techniques at lower temperature ($55^{\circ}C$) compared to conventional phosphating temperature ($80 ~ 90^{\circ}C$ ). Under present condition, it was seen that optimum concentrations of Cu ion in phosphating bath and activator in pre-dip are 0.015% (w/w) and 2.0 g/1, respectively. The coating weight was within the range of 15 ~ 20 g/$\m^2$. When lubricant was applied into phosphating coatings, the amount of lubricating component (total soap) was found to be 6 ~ 10 g/$\m^2$ and the lubricated panel revealed excellent lubricating properties.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.59-70
• /
• 1999

This paper deals with automated computer-aided process planning by which designers can determine operation sequences even if they have little experience in the design of press working products. The computer-aided process planning in hot forging, deep drawing and blanking requires many kinds of technical and empirical skills based on investigation and collection of the knowledge of their processes. An approach to the CAPP system is based on the knowledge-based rules and the process knowledge base consisting of process planning rules is built. The methodology adopted to develop the system is elaborated in this paper. This system has been written in AutoLISP on the AutoCAD with a personal computer and provides powerful capabilities for process planning of hot forging, cold forging, deep drawing and blanking products.

• 한국표면공학회지
• /
• 제36권1호
• /
• pp.59-68
• /
• 2003

Zinc phosphating for cold forming of steel was studied with emphasis on decreasing phosphating temperature. To lower phosphating temperature, some techniques, such as adding Cu ion into bath, using activator in the form of pre-dip, and aeration in bath, instead of using conventional accelerator, namely oxidizing agent, have been tried. It was revealed that phosphating, leading to coatings of improved uniformity and fine crystal size, can be carried out using above techniques at lower temperature (55$^{\circ}C$) compared to conventional phosphating temperature ($80∼90^{\circ}C$). Under present condition, it was seen that optimum concentrations of Cu ion in phosphating bath and activator in pre-dip are 0.015 % (w/w) and 2.0 g/1, respectively. The coating weight was within the range of $\15∼20 g/m^2$. When lubricant was applied into phosphating coatings, the amount of lubricating component (total soap) was found to be$ 6∼10 g/\m^2$ and the lubricated panel revealed excellent lubricating properties.