• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.256-261
• /
• 1997

국내 원전의 사용후핵연료를 경제적으로 수송할 수 있는 대형 수송용기의 국내개발을 위하여 10년의 냉각기간을 갖는 28다발의 PWR 사용후핵연료를 수송할 수 있도록 기본 설계기준을 설정하였다. 이 대형 수송용기에 대하여 개념설계로부터 결정된 차폐두께와 칫수를 기준으로 기본구조를 결정하고 정상수송조건 및 가상사고 조건에 대한 구조해석을 수행하였다. 대형 수송용기는 내부에 많은 양의 PWR 사용후핵연료를 담고 있으므로 이들 핵연료의 중량은 구조설계에 큰 영향을 미치게 된다. 본 연구의 목적은 28다발의 PWR 핵연료를 담은 대형 수송용기가 9m 높이에서 자유낙하하여 충돌사고를 일으켰을 때의 안전성을 파악하기 위한 것이다. 수송용기가 충돌시 충격면에 발생하는 충격력으로 인한 충격완충체의 변형과 충격흡수, 수송용기에 발생하는 응력, 가속도, 충돌력 등의 동적거동을 파악하여 안전성을 입증하였다.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.4
• /
• pp.253-260
• /
• 2011

In this study, computational simulation was performed for thermal management of modules consisting of 10 batteries. Simplified structure and equivalent thermal resistance network was applied to maintain the thermal properties. Verification test of the mesh were in progress to ensure the reliability of 2.6 mm in the narrow gap between the battery, resulting in at least three divided mesh between the shape of the grid was required. Type of air from rear of the module, type of air from top of the module and type of air from bottom of the module were applied and effective cooling methods are discussed based on the location of fan and air intake of the modules. Maximum temperature and temperature differences of modules that directly affect the performance of the module were compared, and also behavior of the fluid was confirmed by comparing the air flow. The best maximum temperature is shown type of air from bottom of the module to $40.27^{\circ}C$ and type of air from top of the module shows smallest temperature difference $0.73^{\circ}C$.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.3
• /
• pp.1-12
• /
• 2016

In this study, the impact of sand and weathered granite soil is analyzed by changing the internal temperature from $20^{\circ}C{\sim}70^{\circ}C$C by installing a heating coil inside the triaxial cell. To check the effect on weathered granite soil due to increase of temperature and number of heating-coiling cycles are analyzed by measuring the temperature by using thermometer installed inside the triaxial cell and due to that deviator stress also occurred during the consolidated undrained test. To analyze the effect of weathered granite soil with change of temperature during undrained testing. The deviator stress and pore pressure is measured. As a result, pore pressure increases and the deviator stress decreases with rise of temperature.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.6
• /
• pp.17-26
• /
• 2016

Characteristic behaviors of geo-structure during freezing and thawing process have to be understood based on fundamental knowledge on phase change in porous soil and interaction between soil and structure. Inversion analysis using published one-dimensional soil freezing tests was conducted to suggest a mechanical model to consider an effect of the ice saturation on Young's modulus. Silty soil was more sensitive to temperature than weathered granite soil and sand, and weathered granite soil was more affected by initial water saturation in stiffness decrease than silty soil. Numerical simulations on chilled gas pipeline showed that shielding effect from surrounding frozen zone around the pipe decreases impact from external load onto the pipe. And a pipe installed in sand backfill showed more heaving due to relatively low stiffness of sand during freezing than that of surrounding in-situ weather granite soil. However, it had more stable stress condition due to effective stress redistribution from external load.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.642-647
• /
• 2000

Nanocrystalline NiAl alloy containing 36at.%Al was synthesized by mechanical alloying (MA). Synthesized powder was sintered by a pulse electric current sintering (PECS) facility. Effecting parameters on the phase transformation were discussed in terms of cooling rate and time spent on heat treatment. The behavior of phase transformation for sintered parts was examined by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) method. Microstructure was observed by scanning electron microscopy (SEM). Martensitic lattice parameter and volume fraction was calculated by direct comparison method in X-ray diffraction analysis.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.140-145
• /
• 2005

Effects of the polyol type and the hard segment content of thermoplastic polyurethane (TPU) on the crystallization of hard segments in TPUs were studied employing differential scanning calorimetry. Diols used for the preparation of TPUs were poly(tetramethylene ether glycol) (PTMEG), poly(propylene glycol) (PPG), polycaprolactone (PCL), poly(butylene adipate) (PBA) the molecular weights of which were 2000 and the hard segments contents of TPUs were $35\~44\;wt\%$. We found that crystallization of hard segments in TPUs were observed at higher temperatures and became faster with increasing hard segment contents of TPUs. The crystallization rate of TPU was also affected by the types of polyols used for the preparation of TPUs. It is postulated that lower miscibility of soft segments and hard segments results in higher crystallization rate and increase of cooling crystallization temperatures due to better hydrogen bending between hard segments in melts.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.94-97
• /
• 1997

금속을 반고상 상태에서 성형하기 위하여 미세조직학적 거동을 밝히기 위해, 본 연 구에서는 높은 비강도, 내마모성을 가진 과공정 Al-Si 합금을 반응고 가공하였을 때의 미세 조직과 상온 가공 후 반고상 온도로 일정시간 유지하였을 때의 미세조직을 관찰하였다. 일 반주조시의 개량 원소 P과 Sr을 첨가하였으며 쐐기형 주조재, 압연재, Si 입자강화 Alrl 복 합재료를 반고상 상태로 가열한 미세조직을 관찰하여 초정 Si입자의 형상 변화를 관찰하였 다. 반응고 교반시 초기에는 P과 Sr의 첨가에 의해 초정 Si입자가 미세화 되었으나 교반이 지속되어 가면서 이러한 경향은 감소하였으며 구상에 가까운 형태로 변화 하였는데, 이는 교반이 지속되면서 첨가 원소의 효과보다 교반 자체의 미세조직 변화 기구에의 의존도가 높 아지기 때문인 것으로 사료된다. 냉각속도를 달리한 쐐기 형상에서의 금형에서 주조된 미세 조직을 관찰한 결과 냉각속도가 느릴 때에만 첨가원소의 영향이 나타났으며, 반고상 온도 유지 후 초정 크기에는 큰 변화가 없었으나 $\alpha$-halo가 형성되고 미세한 Si입자가 생성되었 다. 이는 입자 크기의 성장에 따른 주위의 농도구배로 인해 생성된 것으로 사료된다. 압연시 첨가원소는 핵생성과 재결정을 촉진시켜 초정 Si의 크기를 크게 감소시켰다. 반용융 처리시 초정 Si입자는 약간 성장하였으며, $\alpha$-halo도 생성되었다. 압출한 시료를 반용융 처리한 경 우 Si입자의 형상 변화는 거의 없었으며, Si입자에 형성되어 있던 산화막이 기지와 초정 Si 압자간의 확산장벽으로 작용하여 $\alpha$-halo가 거의 생성되지 않았다. 반응고 교반시 미세조직 변화 기구로는 취성파괴, 합체, 마모를 제안하였으며, 각 공정에서의 초정 Si결정의 크기를 비교하였을 때 45$\mu\textrm{m}$ 이하의 분말을 섞어 압출하였을 때 가장 작은 초정 Si입자 크기를 얻음 을 볼 수 있었다.

• Korean Journal of Food Science and Technology
• /
• v.34 no.5
• /
• pp.830-834
• /
• 2002

본 연구는 동적 전단진동(dynamic shear oscillation) 측정방법을 이용하여 농도가 젤라틴의 동적 레올로지 특성에 미치는 영향에 대하여 관찰하였다. $5^{\circ}C$에서의 젤라틴의 저장 탄성률(storage modulus, G#)과 손실 탄성률(loss modulus, G@)은 농도가 증가함에 따라 증가하는 경향을 보였다. 0.9%를 제외한 모든 농도(2.0-4.9%)에서 젤라틴의 G#은 G@보다 매우 높은 값을 나타냈으며, G#과 G@이 ${\omega}$ 의존성이 없는 true 겔과 같은 거동을 나타냈다. 젤라틴의 농도와 K#(G#에 대한 절편)와의 관계에서는 높은 결정계수$(R^2=0.99)$를 보여주면서 좋은 상관관계를 나타냈다. 여러 온도범위$(-5,\;0,\;5,\;10^{\circ}C)$에서 각 온도별로 측정된 K#값은 $-5^{\circ}C(59.5Pa)\;>\;0^{\circ}C(4.09Pa)\;>\;5^{\circ}C(1.41Pa)\;>\;10^{\circ}C(0.35Pa)$의 순으로 가장 낮은 온도에서 K#값이 가장 높은 것으로 나타났다. 또한 냉각과정에서 최종냉각온도인 $5^{\circ}C$에서 측정된 젤라틴의 최대 G#수치는 4.9%(2399Pa)>4.1%(1744Pa)>3.0%(1159Pa)>2.0%(519.3Pa)>0.9%(3.15Pa)의 순으로 높은 농도에서 높게 나타났다. Aging 10시간 동안 젤라틴 겔의 구조형성은 겉보기 first-order kinetics로부터 겉보기 구조형성 속도상수(K)를 결정함으로써 파악될 수 있다. 젤라틴의 농도가 증가함에 따라 K값은 증가하였으며, 농도와 K값과의 관계는 높은 결정계수$(R^2)$를 나타내면서 좋은 상관관계를 보여주었다(Fig. 7). 10시간 aging 후 G#은주파수$({\omega})$ 의존성이 없이 독립적인 것으로 나타났다. 따라서 이들 젤라틴 겔은 aging하는 동안에 탄성이 점점 강해지고 10시간 후에는 가교결합의 밀도가 증가하여 강한 탄성을 가진 고무질 망상구조(rubber network)를 형성했음을 알 수 있다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.1
• /
• pp.97-104
• /
• 2014

In a coal gasifier for IGCC, hot syngas leaving the gasifier at about 1550oC is rapidly quenched by cold syngas recycled from the gas cleaning process. This study investigated the flow and heat transfer characteristics in the gas quench system of a commercial IGCC process plant under different operating pressures. As the operating pressure increased from 30 bar to 50 bar, the reduced gas velocity shortened the hot syngas core. The hot fly slag particles were retained within the core more effectively, and the heat transfer became more intensive around the hot gas core under higher pressures. Despite the high particle concentrations, the wall erosion by particle impaction was estimated not significant. However, large particles became more stagnant in the transfer duct due to the reduced gas velocity and drag force under higher pressures.

• Nuclear Engineering and Technology
• /
• v.21 no.1
• /
• pp.48-55
• /
• 1989

In this study, simple functional forms which could predict decay heat are referred to and modified in order to analyse more easily long-term behavior of decay heat generated from domestic PWR and CANDU spent fuel. To reduce the difference between the predicted data by functional forms and ORIGEN 2 results and to predict the decay heat under the important parameter(s), sensitivity analysis is performed. By introducing the identified hey parameter, turnup, into the functional forms, the decay heat of spent fuels within a limited rangs of cooling time(3~500 years) becomes predictable for various turnup rates. The predicted decay heat of spent fuels with representative turnup rates such as 33, 37 and 40 GWD/MTU by the functional forms is in so good agreement with ORIGEN 2 results within $\pm$10% difference over the cooling time from 1 to 10$^{5}$ years that the functional forms presented here may be used for engineering purposes such as the thermal design and assessment of the facilities associated with spent fuel management.