• Computational Structural Engineering
• /
• v.4 no.1
• /
• pp.42-43
• /
• 1991

균열성암반의 모형화 기술은 계속적으로 보완발전되어 UDEC이 개발되었으며, 현재 UDEC의 최신판은 블록 내부를 다시 유한차분요소로 분할하여 블록의 소성거동(Mohr-Coulomb Model) 및 쪼개짐을 고려할 수 있고, 절리면에서의 유체흐름 및 유압의 발생, 그리고 열응력 해석 등 평면변형 문제의 정적해석과 지진 및 폭발하중을 고려한 동적해석이 가능하다. UDEC은 전처리 기능이 뛰어나 최소한의 입력데이타로써 전체 모형의 데이타를 자동생성시키며 절리면의 통계학적 자동생성 및 터널형상의 자동생성도 가능하다. UDEC은 실용적인 보강요소를 구비하여 Rock Bolt 뿐만 아니라 그라우트를 고려한 Cable Bolt를 모형화할 수 있으며 국부적인(Key Block)보강으로써 불연속체 전체의 안정을 검토할 수 있다.

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.108-110
• /
• 2005

배전용 변압기의 경우 고장 발생시 직접적인 수용가 측에 피해가 발생되며, 변압기 폭발시 인명 피해까지 우려되고 있다. 변압기 내부 고장으로 절연유가 분출될 경우가 가장 심각한 고장으로 이러한 피해를 방지하기 위해서는 내부 고장에 대한 정확한 해석이 필요하다. 본 연구에서 변압기 권선내에서 발생되는 고장을 유한요소 전자계해석 프로그램(FLUX2D)을 이용하여 해석하였다. 50kVA, 13200/230(V) 단강 변압기의 권선고장시 전자계해석, 1차측 권선고장(turn-to-earth)과 2차측 권선고장(turn-to-turn)을 모의하여 해석하였다. 또한, 권선 내부 고장 및 2차측 단락시 누설자속분포, 1차 및 2차측 고장전류, 권선간의 힘의분포 등을 해석하였다. 분석결과는 변압기의 절연설계 및 단락기계력에 대한 프레임 구조 설계를 위한 자료로 활용된다.

• Journal of the Korean Institute of Gas
• /
• v.26 no.5
• /
• pp.22-27
• /
• 2022

Atomic Layer Deposition (ALD) is a facility that deposits an atomic layer on a wafer by causing a chemical reaction after decomposition using heat or plasma by inputting two or more gases during the semiconductor process. The main gas used at this time is NH₃ (Ammonia). NH₃ has a relatively narrow explosive range with an upper limit (UFL) of 33.6% and a lower limit (LEL) of 15%, but it can explode if a large amount suddenly gathers in one place. It is Velocity and fatal if inhaled or in contact with the skin. NH₃ (Ammonia) of ALD (Atomic Layer Deposition) facility is supplied to the chamber through the gas inlet and discharged after the reaction.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.1
• /
• pp.33-47
• /
• 2013

When a bomb explodes near a tunnel, generated muck should be quickly moved outside for rehabilitation of the tunnel. In this study, the amount of muck generated by an explosion was estimated and a methodology was presented for the prediction of the muck hauling time. To this end, 3D-meshes were made by using SoildWorks and blasting analyses were performed by using AUTODYN. A method was suggested to calculate theoretically the amount of muck which inflows into a tunnel based on the relationship between the tunnel and the fragmentation zone obtained from the analysis results. Also, muck hauling times were predicted based on the selection of construction equipment and the results were compared and analyzed. As a result, it was convinced that the amount of muck flowing into the tunnel could be effectively calculated by classifying the relationship between a tunnel and the fragmentation zone into 4 cases and using the mensuration by parts. Also it was confirmed that the closer blasting location is to the portal and the excavation surface of a tunnel, and the more blasting location deviates from the center line of the tunnel, the lesser amount of muck occurs and thus the muck hauling time decreases as well.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.4
• /
• pp.269-275
• /
• 2020

An explosive bolt is one of many representative pyrotechnic release devices that separates two joined structures using explosives inside the bolt. In this study, a 1/2 inch ridge-cut explosive bolt with an EBW detonator was developed for usage in sled tests. The initial shape design was carried out based on the design method, and the performance test showed that the separation performance was outstanding but fragments occurred. Therefore, numerical analysis was performed to reduce the amount of debris by minimizing the amount of explosives. From the numerical analysis, the separation mechanism and characteristics of the ridge-cut explosive bolts were identified, and the minimum amount of explosives that does not generate debris was proposed. Verification tests revealed that the ridge-cut explosive bolts with the proposed explosive weight minimized fragments while maintaining the separation performance.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.165-173
• /
• 2016

On March 11, 2011, a massive earthquake measuring 9.0 on the Richter scale and subsequent 10-.14 m waves struck the Fukushima Daiichi (FD) Nuclear Power Plant. The main and backup electric power was damaged preventing the cooling system from functioning. Fuel rods overheated and led to hydrogen explosions. If heat in the fuel rods is not dissipated, the nuclear fuel coating material (e.g., Zircaloy) reacts with water vapor to generate hydrogen at high temperatures. This hydrogen is released into the containment area. If the released hydrogen burns, the stability of the containment area is significantly impacted. In this study, researchers performed an explosion analysis in a high-risk explosion area, analyzing the hydrogen distribution in a containment building [1] and the effects of a hydrogen explosion on containment safety. Results indicated that a hydrogen explosion was possible throughout the containment building except the middle area. If an explosion occurs at the top of the containment building with more than 40% of the hydrogen collected or in the bottom right or left side of the of containment building, safety of the containment building could be threatened.

• Journal of the Korean Institute of Gas
• /
• v.3 no.3 s.8
• /
• pp.23-28
• /
• 1999

Variation of explosion characteristics by the blocks in closed vessel was investigated to analyse the effect of the block volume(volume blockage) and the surface area of the blocks(ratio of block surface area to vessel volume). Volume and surface area of blocks in explosion vessel were changed by the combination of blocks. The volume of explosion vessels was 270 liter, and the LPG-air or NG-air mixtures were ignited by the electric spark. Explosion pressure was measured with the strain type pressure transducer. From the experimental results, explosion pressure was decreased by the increase of the volume blockage and the block surface area. And the decrease of explosion pressure was more affected by the volume blockage than the surface area.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.457-462
• /
• 2011

This paper presents a numerical investigation of deflagration to detonation transition (DDT) induced by shock wave and flame interaction in ethylene-air mixtures. Also shows the change of DDT triggering time by wall cooling effect. A model is consisted of the compressible reactive Navier-Stokes equations. And the effect of viscosity, thermal conduction, molecular diffusion, chemical reaction and wall effect are included. Using this model, the generation of hot spot by repeated shock and flame interaction, occurrence of detonation, and wall cooling effect of detonation confining boundaries are studied.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.545-550
• /
• 2023

A pretensioner is a safety device that protects occupants by pulling the seat belt in the event of a vehicle collision. However, since the pretensioner is driven by a explosive method, it is necessary to replace not only the gas generator but also all connecting parts including the manifold after an accident. Therefore, in this paper, we propose an elastic force-based pretensioner that can be used safely and semi-permanently. After analyzing the operating mechanism of the existing pretensioner from a thermodynamic/dynamic point of view, the spring stiffness that can be deployed within an appropriate operating time was determined by converting the gas explosion energy into elastic energy. In addition, the coil spring shape that satisfies the elastic stiffness was designed in consideration of the vehicle interior installation standard. Finally, the operating performance of the pretensioner driven by elastic force was verified through fabrication.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.1
• /
• pp.27-34
• /
• 2005

The present work has been developed the study of interpretation of separation behavior in gas expansion separation(GES) bolt which has the separation characteristics without fragmentation and minimum pyre-shock during the operation of the explosive bolt. In order to obtain the performance of minimum pyre-shock, the present work used non-compressive material instead of separation explosives. The use of the interpretation processor could be extensively helped to design the shape and the amount of explosives in the explosive bolt having complex geometry, and to analyse the separation behavior during the operation. It is also proved that the GES bolt is the most suitable the separation system necessary to minimum pyre-shock and non fragmentation compare with others.