• 한국가스학회지
• /
• 제22권3호
• /
• pp.32-37
• /
• 2018

최근 정부의 미래에너지변환 정책에 따라 천연가스를 활용한 분산발전 시장은 점차 확대될 것으로 예상된다. 분산발전은 전력 수요지 주위의 소규모 발전원을 활용하는 발전방식으로 송배전 인프라 구축 비용과 운용비용, 전력손실을 줄일수 있는 장점이 있다. 천연가스를 이용한 분산발전의 대표적인 예로 Trigeneration System이 있다. 본 연구에서는 Trigeneration System에서 발생되는 냉열 및 엔진 배열을 이용하여 공조대상 실내의 습공기를 제습/냉방/난방 하는 제습공조시스템의 성능 분석에 대한 기초 연구를 수행하였다. 연구결과 제습공조시스템 입출구 온도차가 커질수록 시스템 효율은 높아지고 일반공조시스템 대비 에너지 소비량이 감소하는 것을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.37-44
• /
• 2008

The global warming potential (GWP) of $CO_2$ refrigerant is 1/1300 times lower than that of R134a. Furthermore, the size and weight of the automotive heat pump system can decrease because $CO_2$ operates at high pressure with significantly higher discharge temperature and larger temperature change. The presented $CO_2$ heat pump system was designed for both cooling and heating in fuel cell vehicles. In this study, the performance characteristics of the heat pump system were analyzed for heating, and results for performance were provided for operating conditions when using recovered heat from the stack coolant. The performance of the heat pump system with heater core was compared with that of the conventional heating system with heater core and that of the heat pump system without heater core, and thus the heat pump system with heater core showed the best performance among the selected heating systems. On the other hand, the heating performance of two different types of coolant/air heat pump systems with heater core was compared each other at various coolant inlet temperatures. Furthermore, to use exhausted thermal energy through the radiator, experiments were carried out by changing the arrangement of a radiator and an outdoor evaporator, and quantified the heating effectiveness.

• KIEAE Journal
• /
• 제15권2호
• /
• pp.109-115
• /
• 2015

Purpose: The importance of building airtightness is increased as the demand and expectation of building energy efficiency is growing. Previous research only focused on airtightness of building openings only to improve building airtightness. However, the analysis of difference of airtightness performance according to the characteristic of building structure has not been performed. Therefore, this study analyzed the difference of airtightness performance according to building structural characteristics in a number of ways. Method: Airtightness that are classified as rigid-frame type or wall type are measured and analyzed the difference of airtightness performance between rigid frame type apartments and wall type apartments. This study calculated the heating energy demand and quantitatively analysis using ISO 13790. Futhermore, this study compared research trend of domestic airtightness performance with airtightness standards of the developed countries based on the field measurement. Result: Airtight performance of wall type is better than rigid frame type in terms of energy saving. The difference of heating energy demand between wall type and rigid frame type was $8.14kWh/m^2yr$.

• 한국태양에너지학회 논문집
• /
• 제35권6호
• /
• pp.25-33
• /
• 2015

In this study, heating performance of the air-cooled heat pump with vapor-injection (VI) cycles, re-heater and solar heat storage tank was investigated experimentally. Devices used in the experiment were comprised of a VI compressor, re-heater, economizer, variable evaporator, flat-plate solar collector for hot water, thermal storage tank, etc. As working fluid, refrigerant R410A for heat pump and propylene glycol (PG) for solar collector were used. In this experiment, heating performance was compared by three cycles, A, B and C. In case of Cycle B, heat exchange was conducted between VI suction refrigerant and inlet refrigerant of condenser by re-heater (Re-heater in Fig. 3, No. 3) (Cycle B), and Cycle A was not use re-heater on the same operating conditions. In case of Cycle C, outlet refrigerant from evaporator go to thermal storage tank for getting a thermal energy from solar thermal storage tank while re-heater also used. As a result, Cycle C reached the target temperature of water in a shorter time than Cycle B and Cycle A. In addition, it was founded that, as for the coefficient of heating performance($COP_h$), the performance in Cycle C was improved by 13.6% higher than the performance of Cycle B shown the average $COP_h$ of 3.0 and by 18.9% higher than the performance of Cycle A shown the average $COP_h$ of 2.86. From this results, It was confirmed that the performance of heat pump system with refrigerant re-heater and VI cycle can be improved by applying solar thermal energy as an auxiliary heat source.

• 설비공학논문집
• /
• 제28권10호
• /
• pp.387-393
• /
• 2016

A ground source heat pump system maintains a constant efficiency due to its stable heat source and radiant heat temperature which provide a more effective thermal performance than that of the air source heat pump system. As an eco-friendly renewable energy source, it can reduce electric power and carbon dioxide. In this study, we analyzed one year of data from a web based remote monitoring system to estimate the thermal performance of GSHP with the capacity of 3RT, which is installed in a low energy house located in Daejeon, Korea. This GSHP system is a hybrid system connected to a solar hot water system. Cold and hot water stored in a buffer tank is supplied to six ceiling cassette type fan coil units and a floor panel heating system installed in each room. The results are as follows. First, the GSHP system was operated for ten minutes intermittently in summer in order to decrease the heat load caused by super-insulation. Second, the energy consumption in winter where the system was operated throughout the entire day was 7.5 times higher than that in summer. Moreover, the annual COP of the heating and cooling system was 4.1 in summer and 4.2 in winter, showing little difference. Third, the outlet temperature of the ground heat exchanger in winter decreased from $13^{\circ}C$ in November to $9^{\circ}C$ in February, while that in summer increased from $14^{\circ}C$ to $17^{\circ}C$ showing that the temperature change in winter is greater than that in summer.

• 한국정보전자통신기술학회논문지
• /
• 제2권4호
• /
• pp.29-36
• /
• 2009

본 논문은 버스에 사용되는 연소식 프리히터(Fuel Fired Heater) 퍼지 제어기(Fuzzy controller)를 설계하였다. 프리 히터는 얼마나 빠른 시간 안에 설정한 온도에 다다르는지와 공간내의 온도 편차가 얼마나 작게 발생하는지의 두 가지가 가장 중요한 요소이다. 기존의 연소식 프리히터의 온도 제어 방식으로 사용된 PI 제어기의 온도편차를 줄임과 동시에 응답특성을 개선한 퍼지 제어기를 설계하여 그 성능을 평가하였다. 설계된 퍼지 제어기에서 온도를 설정하면 기존의 PI 제어방식에서는 $25^{\circ}C$의 도달시간이 12분 소요되었으나 퍼지 제어방식에서는 9분 20초 소요되어 기존의 제어기보다 퍼지제어기가 2분 40초의 빠른 응답 성능으로 향상됨을 확인하였다. 난방의 온도 편차에서도 기존의 PI 제어 방식에서는 $2.4^{\circ}C$의 편차를 보인 반면 설계된 퍼지 제어기에서는 $1.6^{\circ}C$로 온도 편차 또한 개선되었음을 확인하였다.

• 설비공학논문집
• /
• 제20권7호
• /
• pp.492-499
• /
• 2008

The cooling load in winter is significant in many commercial buildings and hotels because of the usage of office equipments and the high efficiency of wall insulation. The development of a multi-heat pump that can cover heating and cooling simultaneously for each indoor unit is required. In this study, the performance of a multi-heat pump with 3-piping system was investigated as a function of refrigerant charge and its performance was analyzed in cooling mode, heating mode, and heat recovery mode. COP in the heating or cooling mode showed little dependence on refrigerant charge at overcharge conditions, while those were strongly dependent on refrigerant charge at undercharge conditions and outdoor inlet temperature. In the heat recovery mode, the performance of the system was very sensitive to charge amount at all conditions. Optimum charge amount in the heat recovery mode was 14% lower than that in the cooling mode at the standard condition because the refrigerant only passed the indoor units. It is required to store the excessive refrigerant charge in a storage tank to optimize the system performance at operating modes.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.310-315
• /
• 2008

In this study, experimental study on the heating performance of a $CO_2$ heat pump water heater with a variation of operating conditions such as refrigerant charge amount, outdoor temperature, compressor frequency, EEV opening and water mass flow rate. Based on the test results, the optimum charge amount was 1800 g. At the water mass flow rates of 75, 85, 95 kg/hr, the water heating temperature was 62, 67, $74^{\circ}C$ and COP was 2.6, 2.8, 3.0, respectively. Besides, the water mass flow rate and compressor frequency were varied to maintain above the water heating temperature of $60^{\circ}C$ with the decrease of outdoor temperature. So, The compressor frequency increased beyond 65 Hz and the water mass flow rate was 45 kg/hr at the outdoor temperature of $-13^{\circ}C$, 65 kg/hr at $-8^{\circ}C$, 75 kg/hr at $-3^{\circ}C$ and 85 kg/hr at 2, $7^{\circ}C$. As the outdoor temperature decreased, the heating COP decreased by 2.5-39.8%.

• 한국태양에너지학회 논문집
• /
• 제33권6호
• /
• pp.85-91
• /
• 2013

It is essential to reduce the amount of fossil fuel because facing with the natural problem such as a global warming. To achieve this goal, many of interests in the use of renewable energy is growing. Especially, as one of these renewable energy systems, a solar air heater invention has been conducted for enhancing the efficiency of solar air heater. According to this trend, scale-down sized experiment apparatus was constructed and performed for searching a proper fin and confirming the heat transfer performance by fin shape on constant heat condition to enhance efficiency of solar air heater. In this experiment, heat gain, convection heat transfer coefficient, number of transfer units, Nusselt number, Reynold's number, friction factor, performance factor were investigated in order to evaluate the thermal characteristics based on the real data obtained. By comparison with the each fin performance, a zigzag shape keeping a right angle to the plate had the highest value among them.

• 플랜트 저널
• /
• 제14권3호
• /
• pp.42-48
• /
• 2018

본 연구에서는 판형열교환기 전열면적을 25%, 50%, 75% 증가시킬 때 CHP 회수온도 변화량을 예측하고 변화된 온도를 성능해석 입력 값으로 활용하여 전기출력 변화를 해석하였다. 전열면적 투자비용과 전기 판매수익 증가를 비교하여 경제성 분석을 수행하였다. 광교 열병합발전소 연계운전이 2017년과 유사한 경향으로 이루어지면 CHP 회수온도는 전열면적 증가에 따라 $4^{\circ}C$, $6.3^{\circ}C$, $7.8^{\circ}C$까지 낮아지고 전기출력은 당초 39,025 kW에서 413 kW, 676 kW, 834 kW 증가되어 75% 증가할 경우 39,859 kW 까지 상승하였다. 경제성 분석기준인 NPV는 3.5 억원, 5억원, 5.2억원 까지 발생하여 모든 방안이 투자가치가 있다고 판단된다. 전열면적 증가에 따라 전기출력과 NPV는 비례하여 상승하지만 상승량은 감소하였다. 75%까지 증가할 경우 전기출력과 NPV는 3가지 방안 중 가장 높은 것으로 확인되었다.