• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.919-924
• /
• 2005

Fretting-wear caused by turbulence excitation for KSNP(Korea standard nuclear power plant) steam generator is investigated numerically. Secondary sides density and normal velocity are obtained by the thermal-hydraulic data of the steam generator. Because nonlinear finite element analysis is complex and time consuming, work rate is estimated by using linear analysis for simple straight 2-span tube. Wear volume and depth by using work rate calculation are estimated. Span length, secondary side fluid density and normal velocity are adopted to study the effects on the fretting-wear by turbulence excitation. When secondary sides density and normal velocity is increased, It turns out that secondary side density and normal gap velocity are very important paramater for fretting-wear phenomena of the steam generator.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.190-193
• /
• 2010

The turbulent mixing and combustion of a shear coaxial injector under supercritical pressures have been theoretically/numerically investigated. Turbulent numerical model is based on large eddy simulation with real-fluid transport and thermodynamics over the entire pressure; Soave modification of Redlich-Kwong equation of state, Chung's model for viscosity/conductivity, and Fuller's theorem for diffusivity to take account Takahashi's compressible effect. The results are compared with previous researcher's. The large-scale vortices shedding from the outer rim into the recirculation region to react with gaseous oxygen was investigated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.12
• /
• pp.1885-1891
• /
• 2010

Torque control of wind turbines is important when the wind speed is below the rated speed. The main objective of torque control is to extract the maximum power from the potential aerodynamic power of the wind. Torque control methods for wind turbines are classified as torque-mode control and speed-mode control. In torque-mode control, which is well known and traditionally used in many wind turbines, the torque demand of the generator is proportional to the square of the generator speed. In speed-mode control, a PI controller is used to generate the appropriate torque demand of the generator. In this study, the two torque control methods mentioned above are applied to a 2.75-MW wind turbine; simulation results for real turbulence wind speeds are presented, and the response properties are compared.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.97-103
• /
• 2003

Numerical research has been done for the transverse jet behind a rearward-facings step in turbulent supersonic flow without chemical reaction. Purpose of transverse jet is to enhance mixing of the fuel in the combustor. Two-dimensional unsteady flowfields generated by slot injection into supersonic flow are numerically simulated with the Navier-Stokes equations with two-equation k-$\varepsilon$ turbulence model. Numerical method is used high-order upwind TVD scheme. Eight cases are computed for different slot momentum flux ratios and slot position at downstream of the step. The flow is very similar to the cavity flow, because the jet acts as an obstacle. The numerical results thus show the periodic phenomenon.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.253-260
• /
• 2015

Particle contamination in a cleanroom is very complex with a complicated process and several pieces of spreading equipment. Detailed information on the locations of the contamination sources and the path of the contamination is needed for economical and efficient control of the contaminant particles in such a cleanroom. An allocation method was developed to quantitatively predict the contamination generated from the pollution sources. In this paper, we propose a zoning method to accelerate the computation time for estimating the contributions. Our results showed that we can quantitatively estimate the amount of contamination generated from pollution sources.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.7
• /
• pp.2277-2288
• /
• 1996

This study was performed to analyze the cooling effect of heated ribs which are frequently used for cooling of electronic parts, using the numerical method. To prevent the excessive pressure drop due to turbulence promoters for the enhancement of heat transfer rate especially, the effect of the angle of turbulence promoter was investigated by the numerical analysis. Heat transfer rate with turbulence promoters with rectangular cross-section increased by 13% in average, but the coefficient of pressure drop increased by 1.68 times than that without them. In the present study, triangular cross-sectional shape turbulence promoters were suggested and numerically tested. Pressure drop of turbulence promoter with the 30 degree triangular cross-sectional shape decreased by 30% from that of rectangular cross-section promoters while heat transfer rate was almost the same. While with 4 turbulence promoters, the heat transfer rate increased by 21%, the pressure drop increased 4 times. It means that the higher capacity of cooling fan should be needed. With the triangular cross-sectional shape, the size of vortex region at the rear of promoters became considerably smaller, so pressure drop became smaller. The effect of the change of cross-sectional shape was not found in the flow pattern near the ribs, so that heat transfer characteristics in the ribs were not changed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.6
• /
• pp.452-459
• /
• 2003

The characteristics of fluid-elastic instability and effects of turbulent excitations for the KSNP steam generator tubes were investigated numerically. The information for the thermal-hydraulic data of the steam generator has been obtained by using the ATHOS3-MOD1 code and the flow-induced vibration(FIV) analysis has been conducted by using the PIAT(program for Integrity assessment of SG tube) code. The KSNP steam generator has the concentrated plugging zone at the vicinity of the stay cylinder inside the SG. To investigate the cause of the concentrated tube plugging zone, the FIV analysis has been performed for various column and row number of the steam generator tubes. From the results of FIV analysis the stability ratio due to the fluid-elastic instability and vibrational amplitude due to the turbulent excitation in the concentrated plugged zone have a trend of larger values than those of the outer concentrated tube Plugging zone.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.5
• /
• pp.545-550
• /
• 2012

Steam generator is one of the major components of nuclear power plant and steam generator tubes are the pressure boundary between primary and secondary side, which makes them critical for nuclear safety. As the operating time of nuclear power plant increases, not only damage mechanisms but also scaled deposits on steam generator tubes are known to be problematic causing tube support flow hole blockage and heat fouling. The ability to assess the extent and location of scaled deposits on tubes became essential for management and maintenance of steam generator and eddy current bobbin data can be utilized to measure thickness of scale on tubes. In this paper, tube reference standards with various thickness of scaled deposit has been set up to provide information about the overall deposit condition of steam generator tubes, providing essential tool for steam generator management and maintenance to predict and prevent future damages. Also, methodology to automatically measure scale thickness on tubes has been developed and applied to field data to estimate overall scale amount.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.28-34
• /
• 2019

In this study, pin-fin arrays, which are widely used for cooling turbine blades, were studied. The vortex generator in pin-fin arrays is located in front of the circular tube. The cross-section of the vortex generator is NACA-9410. The purpose of this study is to analyze heat transfer performance and flow characteristics of pin-fin arrays. The position of vortex generator is changed with the vertical flow direction on the bottom wall. Pin-fin arrays were calculated with 6000, 10000 and 15000 Reynolds number. The commercial program ANSYS v18.0 CFX and the turbulence model $k-{\omega}$ SST were used. As a result, the heat transfer performance increased up to 5.8% and pressure loss increased less than 1%.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.493-493
• /
• 2017

부유사 수리실험에서 부유사의 농도를 측정하는 것은 불확실성이 매우 크다. Einstein(1950)은 유사의 pickup function 결정에서 이러한 불확실성 때문에 유사입자의 거동을 발생시키는 양력의 확률을 적용하기도 하였다. 일반적으로 부유사의 측정은 부유사 채집기를 통해 수행하지만, 시간적으로 비효율 적이며, 채집 시 채집기의 부피로 인한 난류 발생으로 채집 후 흐름 변화가 발생할 수 있다. 수리실험의 규모라면 이 문제는 더욱 부각될 수 있다. 연속적인 부유사의 농도 측정을 위해 이러한 점은 개선되어야 하는 문제이다. 본 연구에서는 유사 실험의 이러한 단점을 극복하고자 image processing 기법을 적용하였다. Image processing은 부유사의 농도가 증가할수록 탁도가 증가하는 특성을 이용하여, 부유사 농도를 추정하는 방법이다. 이 과정에서 RGB(Red-Green-Blue)로 색을 표시하는 방식에서 image를 변환하여 gray scale로 전환해야 하며, 파(wave)의 전파에 의한 image 결과의 변형은 없다고 가정하였다. Gray scale과 탁도와의 관계를 도출하기 위해 하상에 유사를 포설하고, 단파(surge)를 발생 시켰다. 실험은 길이 12.0m, 폭 0.8m, 높이 0.75m의 개수로에서 수행하였으며, 수로 상류에 sluice형 gate를 급격하게 개방하는 것으로 단파를 재현하였다. 탁도 측정을 위해 유사 채집기를 이용하였으며, 상기에서 제시한 흐름 교란문제로, 1지점에서 1개의 시간동안만 채집을 수행하였으며, image의 촬영을 병행하였다. 또한 data의 정확도를 높이기 위해 3번의 반복실험을 수행하였다. 실험결과 gray scale과 탁도와는 일정한 관계가 나타났으며, 이를 토대로 gray scale-SSC(suspended sediment concentration)와의 관계를 도출하였다. Bayesian 분석을 이용하여 image processing의 보정(확률적 보정)을 추가적으로 수행하였다. 최종적으로 실측한 값과 image processing을 통한 값을 1:1 curve를 통해 비교하였으며, 약 9%의 평균 오차가 발생하여, image processing과 bayesian 적용을 통한 부유사 농도 측정은 신뢰할 만한 결과를 도출하는 것으로 판단된다.