• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.100-100
• /
• 2017

2016년부터 중국에 수출한 진공포장 쌀이 진공이 풀려 중국 현지 소비자들에게 품질에 대한 신뢰저하로 외면 받아 판매에 어려움을 겪었다. 진공풀림 원인은 주로 포장재의 모양, 과열 열접착 및 운송 중 부주의 등을 들 수가 있다. 따라서 본 연구에서는 쌀 진공포장 후 진공 풀림현상이 발생되는 원인을 분석하고, 진공포장에 적절한 포장재 및 취급조건에 대해 구명하여, 중국 쌀 수출 시 품질신뢰도 및 경쟁력 제고로 쌀 수출 확대를 위해 진공 포장재, 진공포장기술 및 운송 취급 방법을 제시하고자 하였다. 미곡종합처리장에서 사용하고 있는 플라스틱 필름 포장재의 적합 여부를 살펴보기 위하여 산소투과도 및 투습도를 산소투과도 측정장치(OX-Tran Model 2/61, Mocon, USA), 투습도 측정장치(Permatran-W Model 3/33, Mocon, USA)를 이용하여 측정하였다. 적정 열접착 온도를 구명하기 위하여 열접착 작업시간 간격 3, 5, 10초 3수준으로 하고 가열시간을 0.2초~2초까지 9수준으로 설정하여 포장필름을 열접착한 후 접착상태를 조사하였다. 진공 포장된 쌀을 골판지상자에 2차 포장하여 운송할 때 진공풀림 현상이 발생 여부를 조사하기 위해 가상 운송시험을 진동시험 장치를 이용하여 수직 및 수평으로 진동시험을 수행하였으며, 또한 취급조건에 따라 진공풀림을 조사하기 위하여 골판지 상자단위, 비닐포장 단위로 50, 70, 90cm 높이에서 낙하 시험을 하고 진공풀림여부를 조사하였다. 유통 중인 쌀 진공 포장재는 나이론(nylon)+선형저밀도폴리에틸렌(LLDPE) 복합필름으로 산소투과도가 $30{\sim}70cc/m^2{\cdot}day$, 투습도가 $2{\sim}4.5g/m^2{\cdot}day$로 산소투과도 및 투습도가 충분히 낮아 진공포장재로 적합했으며, 적정 열접착온도 조건은 $130{\sim}150^{\circ}C$에서 1~1.5초가량 가열해야 되는 것으로 조사되었다. 진동시험 및 낙하시험결과, 골판지박스 포장 시 완충재를 사이에 넣은 경우 진골풀림이 적었고, 상자단위나 비닐포장단위 모두 가능한 50cm보다 높은 곳에서 낙하충격을 받지 않도록 취급해야 할 것으로 판단되었다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.323-328
• /
• 2002

양파의 껍질에 칼금을 내고 꼭지와 뿌리를 절단한 후 회전하는 두 개의 롤러 위에 양파를 낙하시켜 구르게 하면서 그 위에 고압공기를 분사시켜 양파의 외각 껍질을 제거하는 공기분사식 박피장치의 최적 작동조건을 구명하기 위하여 수행한 시험결과를 요약하면 다음과 같다. 1, 박피장치에 고압공기를 분사하지 않았을 때, 롤러의 원주속도가 빠를수록, 양파의 무게가 가벼울수록 구름소요시간은 줄어들었고 직경방향 구름율이 가장 높았는데, 직경방향 구름소요시간이 가장 짧게 나타나는 주롤러의 원주속도는 2.4 m/s이었다. 2. 주롤러의 원주속도 2.4 m/s일 때 양파의 무게, 분사공기압 및 칼금수가 증가할수록 박피율은 증가하였으며, 박피율이 가장 높은 조건은 칼금수 4개, 분사공기압 3.5 kg/$cm^2$이상이었다. 3. 박피소요시간은 칼금수가 많을수록, 분사공기압이 높을수록 짧아지는 것으로 나타났고, 칼금수를 4개로 하고 분사공기압을 4.0 kg/$cm^2$이상으로 하면 박피소요시간을 2초 이하로 유지할 수 었다. 4. 양파의 껍질강도는 저장기일과 조건에 따라 다르므로 모든 양파의 박피를 위해서는 분사 공기압을 4.0 kg/$cm^2$이상으로 하고 공기분사시간을 2초에서 5초가지 조절할 수 있는 장치를 부착하는 것이 좋을 것으로 판단된다. 5. 시험에 사용된 양파는 무게는 150~350$\pm$30 g, 직경 60~120 mm의 크기로 우리나라에서 생산되는 양파의 98%에 적용이 가능할 것으로 생각된다.

• The Journal of Engineering Geology
• /
• v.32 no.4
• /
• pp.499-511
• /
• 2022

In this study, a vertical drop test was carried out to identify the performance of flexible wire rope rockfall protection fence by 100 kJ rockfall energy according to ETAG 027. The flexible wire rope, which consists of wire rope and spring. is especially enhanced the elasticity and flexibility so that it can be longer elongated when the rope is impacted by rockfall compared to original wire rope, and that results longer increase of contact time between rockfall and wire rope and increase rockfall energy absorption capability and decreases rockfall impact force. The test results shows that the plastic deformation occurred in middle post and the final deflection of the middle post was 1.15 m, which is lower than 2.0 m determined by ETAG 027. This vertical test verified the flexible wire rope rockfall protection fence can successfully absorb 102.9 kJ rockfall energy.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.556-558
• /
• 2022

This paper proposes a CanSat system with a vehicle tracking function based on Jetson Nano, a high-performance small computer capable of operating artificial intelligence algorithms. The CanSat system consists of a CanSat and a ground station. The CanSat falls in the atmosphere and transmits the data obtained through the installed sensors to the ground station using wireless communication. The existing CanSat is limited to the mission of simply transmitting the collected information to the ground station, and there is a limit to efficiently performing the mission due to the limited fall time and bandwidth limitation of wireless communication. The Jetson Nano based CanSat proposed in this paper uses a pre-trained neural network model to detect the location of a vehicle in each image taken from the air in real time, and then uses a 2-axis motor to move the camera to track the vehicle.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.1
• /
• pp.33-38
• /
• 2009

The use of portable devices has created the need for new reliability criterion of drop impact tests because of the tendency to accidentally drop in the use of these devices. The effects of different PCB surface finishes (organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG)) and high temperature storage (HTS) test on the drop reliability were studied. Various drop test conditions were used to evaluate a drop reliability of assemblies to endure such impact and shock load. In the case of the as-reflowed samples (no HTS test), the SAC/OSP boards exhibited a better drop impact reliability than that of SAC/ENIG. However, the reverse was true if HTS test is performed. In addition, significant decrease of drop reliability was observed for both SAC/ENIG and SAC/OSP assemblies after HTS test. It was also observed that the thickness of intermetallic compound layer do play an important role in the brittle fracture of drop test.

• Journal of Korean Society of Forest Science
• /
• v.86 no.3
• /
• pp.334-341
• /
• 1997

Artificial precipitation test with sprinkler system was carried out to develop the collection method of arboreal larvae(proctotrupoid wasps) of pine needle gall midge for biological control in 1995. Effects of larvae falling on each amount of precipitation, season of precipitation and time of precipitation of a day following artificial precipitation were examined during the period of larvae falling season. The results obtained were summarized as follows; 1. Artificial precipitation with sprinkler system was highly effective for collection of pine needle gall midge larvae and the most suitable amount of precipitation was 5.3-9.4mm; application amount and hours of water were $8,000-16.000{\ell}$ and 180-360 minutes, respectively. 2. The most effective period of larvae collection for artificial precipitation was approximately 20 days, from early through mid November, and larvae falling was 93.4% of the total number of larvae collection during this period. 3. Larvae falling from the tree crown was not affected by the artificial precipitation for the precipitation hour intervals in a day. 4. The percentage of parasitism of collected larvae of pine needle gall midge in November exceeded that of December but was not significantly different between two seasons. 5. Artificial precipitation of sprinkler system was effective in reducing 34% of gall formation after one year at collected sites of pine needle gall midge larvae. 6. The collection method of larvae following artificial precipitation was effective in reducing the expenses by 14-50% than that of collection method of infested needles.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.6
• /
• pp.481-489
• /
• 2000

A time-frequency analysis method was developed to analyze the dispersive waves caused by impact loads in structural members such as beams and plates. Stress waves generated by ball drop and pencil lead break were recorded by ultrasonic transducers and acoustic emission (AE) sensors. Wavelet transform (WT) using Gabor function was employed to analyze the dispersive waves in the time-frequency domain, and then to find the arrival time of the waves as a function of frequency. The measured group velocities in the beam and the plate were compared with the predictions based on the Timoshenko beam theory and Rayleigh-Lamb frequency equations, respectively. The agreements were found to be very good.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.947-958
• /
• 1986

물-증기 역류 성층이상유동에서의 평균 액체층 두께가 여러가지 경사각과 종횡비에 따라 측정되었다. 난류유동에 있어서 전단응력분포의 선형화와 von Karman의 혼합길이 이론을 근거로 평균 액체층의 두께에 대한 관계식이 제시되었으며 실험결과와 잘 일치하였음을 보였다. 접촉면에서의 조파저항이 고려되지 않은 해석결과는, 수평 성층유동의 경우에, 평균 액체층 두께보다는 오히려 파곡까지의 액체층 두께를 예측하고 있는 것으로 나타났다. 또한 평균 액체층 두께에 대한 실험 상관관계식이 계산시 편의를 위해 쉽게 인지할 수 있는 매개변수들의 항들롤 제시되었다.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.4 no.1
• /
• pp.47-62
• /
• 2001

An experimental study was peformed to provide the numerical models to predict the physical fate of marine debris with the key information concerning their trifling and sinkage on the sea. For hygroscopic materials their floating times in a pseudo ocean environment were measured, and for non-hygroscopic objects their drifting limes in a certain wave condition were measured. For sinking materials or objects became to be sinkable free falling experiment was performed to evaluate their falling speed. Summarized information was condensed into a numerical model to predict the most possible region of a significant marine debris accumulation, and the seas connected to the Han river and the Nak-Dong river were considered for the simulation.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.4
• /
• pp.106-117
• /
• 2012

Indirected heating dryer is used as one of the food waste treatment technologies for the production of the drier material supplied to the recycling facilities or end user. This study investigated the effect on drying efficiency for the operation of rotating screw with the circulating and falling movements on indirected drying process of food waste. The screw operating condition showed higher drying efficiency despite of the shorter drying time compared to the screw non-operating condition. The moisture content decreased to 14.4% from the initial moisture content of 77.1% after drying 5 hours in the screw operating condition. On the other hand, in the screw non-operating condition, the moisture content decreased slightly to 35.6% after drying 16 hours. During the drying process, variations of the water evaporation rate and particle size showed different tendencies depending on the moisture content regions. In the higher moisture content region above the glue zone(moisture content of about 50%-60%), the particle size increased and the water evaporation rate reached the highest peak. In the range of glue zone, the particle size maximized while the water evaporation rate decreased sharply. In the lower moisture content region below the glue zone, the water evaporation rate and particle size both decreased at the same time. The particle size distribution was widely ranged from 25.0mm to 0.25mm in the screw operating condition while it was narrowly distributed in the screw non-operating condition from 25.0mm to 3.56mm, especially highly concentrated to 25.0mm. It was regarded that the hygroscopic, capillary and gravitational water evaporated more easily from the intra-particle during the circulating and falling movement caused by the rotating of the screw and the difference of the cohesional force of water within intra-particle depending on the moisture content regions. Comparing the effect of the circulating and falling movement on drying efficiency, the water evaporation rates per time and per weight of dry solid in the screw operating condition were higher about 364% and 356%, respectively, than those of the screw non-operating condition.