• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.406-413
• /
• 2011

This paper presents the shape optimization of a nonaxisymmetric endwall and endwall boundary layer fence which improve the aerothermal environment of a gas turbine passage. The endwall and fence methods were used simultaneously. The turbine passage was simulated by a $90^{\circ}$ turning duct ($Re_D$=360,000). The main purpose of the present investigation was to focus on finding a nonaxisymmetric endwall and boundary layer fence with minimum total pressure loss in the passage and heat transfer coefficient on the endwall of the duct. An approximate optimization method was used for the investigation to secure the computational efficiency. Results indicated that a significant improvement in aerothermal environment can be achieved through the application of a nonaxisymmetric endwall and boundary layer fence.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.5
• /
• pp.5-12
• /
• 2015

This paper presents a numerical investigation of the effect of the dihedral stator on the loss in a transonic axial compressor. Four stator geometries with different stacking line variables are tested in the flow simulations over the whole operating range. It is found that a large shroud loss at the rotor outlet and the subsequent shroud corner separation in the stator passage occur at low mass flow rate. The hub dihedral stator and bowed blade generate unexpected hub-corner-separation, thereby causing a large total pressure loss over the entire operating range. However, the corresponding blockage forces the high momentum flow near the hub to divert toward the upper part of the passage suppressing the negative axial velocity region. The dihedral stator increases deflection angle and secondary vorticity near the endwall where the dihedral is applied. As a result, the endwall loss which is related to the endwall relative velocity decreases.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.3
• /
• pp.527-539
• /
• 1992

본 연구에서는 터빈익렬의 입구유동면에 주어지는 끝벽 경계층유동에 의하여 익렬 내의 유동에서 발생하는 여러 와류들에 의한 2차 유동과 이와 연관된 여러가지 3차원 점성유동 현상 그리고 이에 따른 유동손실을 보다 정확히 예측하기 위한 수치해 석적 연구를 수행하였으며, 이에 필요한 수치해석적 연구를 수행하였으며, 이에 필요 한 수치해석코드를 작성하였다.유동특성에 대하여 상세한 연구결과가 보고되어 있 는 UTRC(United Technologies Research Center) 평면 터빈익렬을 연구대상으로 채택하 여 익렬 내의 3차원 유동특성을 연구하고 계산한 결과를 기존의 결과와 비교 검토하였 다. 강한 2차유동이 존재하는 경우에 발생하는 수치확산을 감소시키기 위하여 대류 항에 대하여 2차 정확도(second-order accuracy)의 선형상류도식(linear upwind sche- me)을 사용하여 일반적으로 널리 사용되는 하이브리드도식(hybrid scheme)에 의한 해 석결과와 비교하였다. 터빈익렬 내의 난류 유동은 익렬의 회전과 유선의 만곡 등에 의한 영향으로 복잡한 유동현상을 나타내지만, 터빈익렬 내의 난류유동 특성에 대한 실험결과가 아직까지는 부족하고 또한 본 연구에서는 평균유동값의 정확한 해석에 중 점을 두었으므로 표준 k-.epsilon. 모델을 사용하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.1007-1013
• /
• 2013

This study aims to analyze the aerodynamics when the geometry of the turbine rotor is modified. The turbine used in this study is a small engine used in the APU of a helicopter. It is difficult to improve the performance of small engines owing to the structural weakness of the blade tip. Therefore, the improvement of the hub geometry is investigated in many ways. The working fluid of a turbine is a high-temperature and high-pressure gas. The heat transfer rate of the turbine surface should be considered to avoid the destruction of blade owing to the heat load. The SST turbulence model gives an excellent prediction of the aerodynamic behavior and heat transfer characteristics when the numerical simulations are compared with the experimental results. In conclusion, the aerodynamic efficiency is improved when a bulbous design is applied to the leading edge near the hub. The endwall loss is reduced by 15%.