• Proceedings of the KSEE Conference
• /
• 2008.10a
• /
• pp.17-28
• /
• 2008

국책사업이나 SOC의 확충을 위한 도로 및 철도의 건설에서 적용되는 터널의 단면크기를 보면, $50m^2$에서부터 $100m^2$이상의 중 대단면 터널이 주를 이루고 있으나, 전력구, 통신구, 소규모로 운영되는 광산의 채광용 터널, 용수를 위한 도수로터널 등 특수한 용도로 설계, 시공되고 있는 터널에서는 $20m^2$이하의 단면크기를 갖는 경우가 있다. 이러한 소단면 터널의 경우에는 협소한 작업공간으로 인하여 적용공법 뿐만 아니라 장비의 사용 또한 제약을 받게 되어 작업효율이 저하되고 공사기간이 늘어나게 되는 등 여러 가지 문제점을 안고 있다. 특히, 에멀젼 폭약을 사용하는 발파에서 먼저 기폭된 발파공의 충격압력에 의해 인접공의 폭약이 예비압축(Precompression)되어 사압현상을 일으키고 잔류약을 발생시키는 사례가 종종 발생하고 있다. 사압현상은 당해 발파의 실패와 함께 2차적인 사고의 위험요인이 될 수 있으므로 이를 방지하기 위한 대책을 수립하여야 한다. 이를 위해 기존 문헌을 통하여 사압현상의 원인과 발생 가능성을 검토하였고, 국내에서 주로 사용되는 에멀전폭약의 수중 내충격성시험과 충격압력 전달시험을 실시하여 사압현상의 발생정도를 측정하였으며, 사압현상이 발생한 소단면 터널현장을 대상으로 대책을 수립하여 적용하였다. 심발방법을 변경하여 전단의 충격압력을 견딜 수 있는 공간격을 확보하고 뇌관의 초시간격을 적절하게 배치한 발파패턴을 적용한결과, 사압현상을 억제하고 잔류약의 발생을 감소시켜 계획 굴진장을 확보하고 파쇄석의 크기를 감소시키는 등 양호한 결과를 얻을 수 있었다.

• Explosives and Blasting
• /
• v.41 no.3
• /
• pp.13-25
• /
• 2023

The conventional bench blasting method uses the bottom initiation in all blast holes in a round, whereas the MDS (mixture detonation system) method applies the bottom and top initiations alternately according to the spatial position or temporal sequence of each blast hole. The former and latter are respectively called the SMDS (spatial MDS) and TMDS (temporal MDS) methods. Another variant called MMDS (modified MDS) is designed for the specific use in the site having a fly-rock problem. This study compares the MDS method to the conventional method in the aspect of rock fracturing effect. The comparison is made by numerical simulations for a two-row bench blasting model in the LS-DYNA. The SPH-FEM coupling method is utilized for constructing the blasting model. The SPH elements are used for the rock in the near-field region of the blast holes, and the FEM elements for that in the far-field region. The RHT material model is used for the rock. As a result of the simulations, it was found that up to 0.4 m deeper damaged zone was appeared in the SMDS method than in the conventional method for the case of the burden 1.6 m and bench height 3.0 m. In addition, the fly-rock velocity to the normal direction of the bench slope was appeared about 2.0 m/s lower in the MMDS method compared to the other methods.

• Explosives and Blasting
• /
• v.31 no.2
• /
• pp.14-24
• /
• 2013

The most effective way of the rock removing works in the downtown area is to removing rocks by splitting the rock by blasting with small amount of explosives in the hole. However environmental factors not only limit the applications but also increase the forbidden area. As this is a distributed multi-stage blasting method and to reduce vibration by applying the optimized precisioncontrol-blasting method, it is applicable in all situations. The process is to fix the stemming-help plastic sheet to the hole entrance when stemming explosives and insert detonator and explosive primer with same delay time, two or three sets. This method is more efficient in the downtown area where claims and dispute from vibration are expected. This method is easily usable by designing blast pattern even in the area where delay time blasting is difficult after multi-stage explosive stemming due to short length of blast hole (1.2~3.0m) and there is no detonator wire shortage or dead-pressure.

• Explosives and Blasting
• /
• v.26 no.2
• /
• pp.29-37
• /
• 2008

In general, the size of tunnel cross section in construction site is $50{\sim}200m^2$. But, electric cable tunnel, telecommunication cable tunnel, mine tunnel. Waterproof tunnel have small cross section less than $20m^2$. There are so many problem at small sectional tunnel: restriction of equipment, dead pressure by precompression, loss of efficiency, increase of work time. Especially, explosives remainder by precompression of previous detonation is serious problem. To find its measures of dead pressure (explosives remainder), the following series of progress have been conducted: (1) survey of previous study (2) investigate causes of dead pressure (3) set up of its measures (4) application and appraisal at tunnel site. The measures, change of cut pattern, hole space over 40cm, adjustment of delay time, are proved by experimental results.