• Korean Journal of Plant Taxonomy
• /
• v.47 no.3
• /
• pp.222-235
• /
• 2017

A comparative study of the leaf epidermal micromorphology in the tribe Neillieae (Neillia: 4 species, 4 varieties; Physocarpus: 5 species; Stephanandra: 2 species) was carried out using scanning electron microscopy in order to evaluate the taxonomic and systematic implications of these characteristics. The leaves of the genera Neillia and Stephanandra were hypostomatic, whereas those of P. monogynus, P. opulifolius were amphistomatic. The range of the size of the stomata is $12.02-34.39{\times}10.76-27.13{\mu}m$; the smallest was found in N. thyrsiflora (average $13.98{\times}12.43{\mu}m$; $L{\times}W$), while the largest was measured in N. gracilis (average $26.82{\times}20.67{\mu}m$; $L{\times}W$). Paracytic stomata complexes are only found in N. affinis, and the anomocytic type was most commonly found. The papillate epidermal cell type was only observed on the abaxial surfaces of P. insularis. Platelet epicuticular waxes were found on the adaxial surfaces of N. affinis and S. tanakae. Four types (unicellular non-glandular, two- to five-armed, stellate, and glandular) of trichomes were found on the leaves. Stellates were observed in all species of Physocarpus except for P. insularis. Consequently, leaf epidermal micromorphological characteristics (e.g., the presence of papillate epidermal cells and stellate, and stomata complexes) may have high taxonomic and systematic value in Neillieae. Our results strongly support previous molecular phylogenetic and palynological hypotheses that Stephanandra and Neillia are a single genus and that Physocarpus insularis should be considered as a member of Spiraea.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1249-1255
• /
• 2011

In modern large-scale semiconductor manufacturing clean rooms, the energy consumed by the outdoor air-conditioning system during heating, humidification, cooling, and dehumidification of the incoming outdoor air represents about 45% of the total air-conditioning load required to maintain a clean-room environment. In particular, the energy required for humidification of the outdoor air in winter is very high. Therefore, evaluation and comparison of the energy consumption in key humidification systems, viz., steam-humidification and water-spray-humidification systems, used in outdoor air-conditioning systems would be useful to reduce the outdoor air-conditioning load in clean rooms. In the present study, an experiment with an outdoor air flow of 1000 $m^3$/h was conducted to compare the air-conditioning process and energy consumption in outdoor air-conditioning systems with electrodeboiler steam humidifiers and air-washer water spray humidification systems. The experimental results showed that the water-spray-humidification-type outdoor air-conditioning system consumed less electrical power than did the steam-humidification-type system and was more energy efficient during winter.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.90-93
• /
• 2007

밀도가 높고 주기적으로 배열된 실리콘 나노점이 실리콘 기판위에 형성 되었다. 실리콘 나노점을 형성하기 위해 사용된 나노패턴의 지름은 20 나노미터(nm)이고 깊이는 40 nm 이었으며 기공과 기공사이의 거리는 50 nm 였다. 나노미터 크기의 패턴을 형성시키기 위해서 자기조립물질을 사용했으며 폴리스티렌(PS) 바탕에 벌집형태로 평행하게 배열된 실린더 모양의 폴리메틸메타아크릴레이트(PMMA)의 구조를 형성하였다 폴리메틸메타아크릴레이트를 아세트산으로 제거하여 폴리스티렌만 남아있는 나노크기의 마스크를 만들었다. 형성된 나노패턴에 전자빔 기상증착장치를 사용하여 금 박막을 $100\;{\AA}$ 증착하고 리프트오프(lift-off) 방식으로 금 나노점을 만들었다. 형성된 금 나노점을 불소기반의 화학반응성 식각법을 이용하여 식각하고 황산으로 제거하였다. 형성된 실리콘 나노점의 지름은 24 nm 였고 높이는 20 nm 였다.

• Journal of Technologic Dentistry
• /
• v.39 no.2
• /
• pp.93-99
• /
• 2017

Purpose: With the development of digital dental technology, we are manufacturing prosthetic crown in various ways. However, the wax-up method that makes existing prosthetic crown is also used steadily. Thus, we will compare the shape of the crown designed with wax-up and the crown designed with CAD. Methods: Sculpt the crown with wax-up on the model to 10 dental technicians. The same model was used to design the crown CAD. Measure the size of the sculpted crown. The shapes were compared in three dimensions. Results: As a result, we could observe a difference in size and shape in crown designed with wax - up crown and crown. Conclusion: These results suggest that there are differences according to the method of carving crown and the method of processing.

• Journal of Technologic Dentistry
• /
• v.12 no.1
• /
• pp.121-124
• /
• 1990

The purpose of this study was to evaluate the effect of three different retention forms on the bond strength when complete denture repaired. Total 75 samples were divided into 3 groups(Dove-tail form, bevel form, rabbit form). The completed resin samples were compressed in Instron Testing Machine until gross fracture occurred to examine the effect on the bond strength of resin base. The results of the experiment were as follows : 1. The difference of bond strength according to three retention forms were not statistically significant(P>0.05). 2. Dove-tail form was strongest to bond strength among the three retention forms.

• Journal of Ginseng Research
• /
• v.12 no.1
• /
• pp.30-39
• /
• 1988

This study was conducted to investigate the effects of light intensity and temperature on the physiological characteristics and growth of ginseng leaves. The higher the transmittance of the shade, the greater the area was decreased. In contrast, however, the amount of transpiration was increased. There was no significant difference in the number of stomata, but the size of stomata was distinctively decreased. The higher the transmittance of the shade, the more the contents of total chlorophyll, chlorophyll a and b, and cartooned were decreased. In contrast, however, the aye ratio of chlorophyll was increased. Regardless of temperature, the contents of chlorophyll providing maximum photosynthesis at the end of June and August were 2.1mg and 1 8mg/g F.W. respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.307-310
• /
• 2004

전기영동전착법을 이용한 초전도 후막선재의 제작은 제작 장치와 공정이 간단하고 두께제어 및 다양한 형태의 초전도 막과 선재 제작이 가능한 경제적 효율성과 기술적 장점을 가지고 있다. 따라서 초전도 후막의 특성향상을 위하여 전착공정 과정에서 입자의 치밀성 및 배향성 향상을 위한 칙적화 방안과, 건조 및 열처리 과정에서 발생되는 크랙 및 기공현상과 같은 문제점을 극복 할 수 있는 균일한 후막 표면 화보에 관한 비교 분석 연구를 수행하였다. 전기영동전착법에 의한 초전도후막 제작을 위한 조건 중 현탁용매 조건에 대한 최적화를 구현함으로써 전착 불균일성에 따른 초전도 특성 저하요인인 후막표면의 기공과 크랙현상을 최소화하였다. 전기영동 전착법에 의한 초전도 후막의 특성을 향상시키기 위한 제작 방법으로 각 용매별에 따른 안정화된 제작 조건을 구현하였다.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.566-571
• /
• 2003

Hydroxyapatite (HAp)/Polyacrylic Acid(PAA) homogeneous composites of four different composition ratio were preparation by co-precipitation process with synthetic HAp and PAA as a binder. HAP/PAA composites were molding by cold isostatic pressing and were sintering by various condition in air. Crystallinity and structure of sintered HAp/PAA composites were investigated by XRD and FT-IR. Also, the compressive strength and the fracture surface of sintered specimens were measured by UTM and SEM. HAp/PAA composites were showed phase transformation of partially ${\alpha}$, ${\beta}$-tricalcium phosphate at sintering condition of 1200$^{\circ}C$ and 3 h. The pore size and porosity of sintered body were showed the range of 0.2∼3.0 $\mu\textrm{m}$ and 0.49∼13.43%, respectively. The compressive strength of sintered specimens were appeared the range of 36.6∼58.2 MPa. From these results, the sintered HAp/PAA comosites can be accounted for the microporous HAp having a good compressive strength due to homogeneous pore morphology.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.3 s.40
• /
• pp.13-17
• /
• 2006

Dense and periodic arrays of holes and tungsten none dots were fabricated on silicon oxide and silicon. The holes were approximately 25 nm wide, 40 nm deep, and 60 nm apart. To obtain nano-size patterns, self-assembling resists were used to produce layer of hexagonally ordered parallel cylinders of polymethylmethacrylate(PMMA) in polystyrene(PS) matrix. The PMMA cylinders were degraded and removed with acetic acid rinse to produce a PS mask for pattern transfer. The silicon oxide was removed by fluorine-based reactive ion etching(RIE). Selectively deposited tungsten nano dots were formed inside nano-sized trench by using a low pressure chemical vapor deposition(LPCVD) method. Tungsten nano dot and trenched silicon sizes were 26 nm and 30 nm, respectively.

• Polymer(Korea)
• /
• v.27 no.1
• /
• pp.46-51
• /
• 2003

In this work, the electrode far fuel cell was fabricated by mixing carbon blacks with activated carbon fibers (ACFs) in order to form the proper three phase distribution, and then the change of electrode in three phase distribution was investigated. Pt loading yield with ACF content and Pt particle size were determined by AAS and XRD measurements, respectively. And the pore structures, including specific surface area ($S_{BET}$), microporosity, and pore size distribution (PSD) for each electrode were systematically investigated by BET volumetric measurement. The morphology of electrode in three phase distribution was determined by SEM. As an experimental result, it was observed that Pt loading yield was not influenced on the content of ACF. While, the electrode in three phase distribution was largely improved in the case of 30% ACF addition on carbon blacks. These results were probably explained by the increase of the portion of micropores, resulting in increasing the active sites of catalyst.