• Membrane Journal
• /
• v.17 no.2
• /
• pp.124-133
• /
• 2007

In this study, we treated lake water by 2 kinds of multichannel ceramic micro filtration membranes. We could investigate effects of $N_2-back-flushing$ time (BT) and transmembrane pressure (TMP), and find optimal operating conditions. The BT were changed in $10{\sim}60$ sec, TMP in $0.6{\sim}2.0$ bar at fixed filtration time (FT) 8 min, flow rate 2.0 L/min and back-flushing pressure 2.0 bar. Also, the optimal conditions were discussed in the viewpoints of resistance of membrane fouling $(R_f)$, dimensionless permeate flux $(J/J_o)$, permeate flux (J) and total permeate volume $(V_T)$. As result, optimal back-flushing conditions for HC04 ($0.4{\mu}m$ pore size) and HC10 membrane $(1.0{\mu}m)$ were BT=10 sec and BT=20 sec, respectively. Then, higher TMP should increase the driving force, and could produce more VT. Average rejection rates of pollutants were higher than 95.4% for turbidity, $12.7{\sim}20.1%\;for\;COD_{Mn},\;0.0{\sim}6.4%\;for\;NH_3-N,\;1.9{\sim}4.6%$ for T-N and $34.9{\sim}88.4%$ for T-P.

• Membrane Journal
• /
• v.14 no.2
• /
• pp.108-116
• /
• 2004

In this study, the pore-filled ion-exchange membranes were prepared by using the asymmetric PVDF membrane as a nascent membrane. First, the solution of PVBCI having the chlorornethylate aryl ring of 80 percents and DABCO was made with the mixed solvent of THF and DU (8:2). These mixed solution was then, filled in the pores of PVDF membrane, and left for a day to complete the gelation. Finally the pore-filled anion-exchange membrane is obtained fallowed by the amination of the remaining chloromethyl groups with trimethylamine (TMA, 40 wt% in water) forming the positive ammonium ion sites. This 2 step procedure enabled us to produce the pore-filled membranes without change of size, and to control the properties of final membrane with various degree of cross-linking. The results of SEM and AFM showed the polyelectrolyte existed in the pores of nascent membrane as a certain configuration. From the investigation of the solvent affecting much to the permeability and rejection, it was found that the membranes using mixed solvent of THE and DMF (8:2) showed better performances than the membranes produced by THF only. The result of an investigation for the water permeability of the final membrane at low pressure (100 Kpa) showed a typical ultrafiltration membrane's permeability (8 ∼ 10 kg/$m^2$hr) and good values of rejection (55∼60 percent).

• Membrane Journal
• /
• v.16 no.1
• /
• pp.31-38
• /
• 2006

The ceramic microfiltration system with periodic $N_2$-back-flushing was operated for treating paper wastewater discharged from a company making toilet papers by recycling milk or juice cartons. Two kinds of alumina membranes with 7 channels used here for recycling paper wastewater. The optimal filtration time interval for HC04 membrane with $0.4{\mu}m$ pore size was lower value of 4 min than 16 min for HC10 with $1.0{\mu}m$ pore size at fixed back-flushing time 40 sec, trans-membrane pressure $1.0kg_f/cm^2$ and back-flushing pressure $5.0kg_f/cm^2$. From the results of TMP effect at fixed filtration time interval and back-flushing time, the lower TMP was better on membrane fouling because high TMP could make easily membrane cake and fouling inside membrane structure. However, we could acquire the highest volume of total permeate at the highest TMP for the reason that TMP was driving force in our filtration system to treat paper wastewater. Then the permeate water of low turbidity was acquired in our microfiltration system using multi channels ceramic membranes, and the treated water could be reused in paper process.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.116-119
• /
• 2000

본 연구에서는 온도의 상승에 의하여 부피가 팽창하는 열팽창 고무 치공구의 팽창 특성을 이용하여 열경화성 복합재료를 경화하고 압축하는 과정을 실험과 모델링을 통하여 해석하였으며, 열가소성 복합재료의 함침공정을 연구하였다. 열팽창 고무치공구가 사용되는 닫힌계와 열린계에서 예상되는 압력을 이론적으로 유도하였고, 경화가 수반되는 과정에 있어서는 실험을 통하여 열팽창치공구와 프리프레그가 나타내는 압력을 측정하였다. 온도가 상승하고 경화가 수반되는 경우에 등속도 압축실험에 의하여 얻어지는 응력-변형율 곡선은 비선형점탄성 특성을 보여주었는데, 본 연구에서는 Maxwell모델을 KWW(Kohlrausch-Williame-Watts)식으로 변형시킨 모델식을 이용하여 이를 매우 정확하게 표현할 수 있었다. 또한 고무치공구를 이용하여 열가소성 수지의 복합재료 성형공정을 실험하였고, 중성자 레디오그래피 촬영을 통하여 기공의 분포를 관찰하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.335-342
• /
• 1986

The feasibility of simultaneous measurement of gas-liquid tow-phase flowrate and quality with a sharp-edged orifice has been investigated. Instantaneous pressure drop curves were monitored for various combinations of gas and liquid flowrates in the bubbly flow regime and some statistical properties of the curves were calculated. The time-averaged value of pressure drop increases with increasing gas and liquid flowrate, whereas the mean amplitude and the intensity of fluctuation monotonically increase as void fraction becomes larger in the flow regime. The statistical furctions for the instantaneous curves indicate a consistent pattern throughout the flow regime and the probability density function, which as a single-peaked and symmetrical distribution, is well predicted by the Gaussian distribution function. The results indicate that simultaneous determination of two-phase flowrate and quality may be possible based upon the statistical analysis of instaneous pressure drop curves measured in a sharp-edged orifice.

• Membrane Journal
• /
• v.22 no.6
• /
• pp.470-480
• /
• 2012

In this study, for a linear tubular membrane with constant diameter the mass balance considering permeate velocity of the each unit length was established. On this basis, mathematical modelling of flows in a pipe was solved using nonlinear second order differential equations as well as steady-state equation. Since this equation is nonlinear, Gauss-Seidel method or another iteration method were used to solve the differential equations. Simulation algorithm for numerical solutions was presented. Also since the permeate flow is varied as operating condition, the solution of equations at each conditions using numerical integrations such as Simpson's rules was used. In order to analyze and compare simulation results, we have performed experiments using a hollow fiber membrane with almost identical tubular membrane. Comparison of theoretical and experimental results, pressure drop, flow rate, and permeate flow in a hollow fiber membrane, were illustrated.

• Korean Journal of Materials Research
• /
• v.6 no.3
• /
• pp.318-323
• /
• 1996

원소 분말을 합성하여 Ti5SI3 화합물을 합성하는 방법을 연구하였다. 합성법으로서는 기본적으로 반응소결법을 사용하였으며, 치밀화를 위하여는 유사-열간 정수압 성형법(PHIP, pseude-hot isostatic pressing)을 사용하였다. 반응소결법에서는 분말의 입도, 반응온도 및 유지시간이 소결밀도에 영향을 주었으며, PHIP법에 의한 치밀화에서는 압력 및 유지 간이 주요 변수로 사용되었다. 이들 변수중 미세한 입도와 유지시간이 기공을 감소시켰다. 또한 Cu의 첨가 영향을 연구하였는데, 약 6wt%이내의 Cu 첨가는 밀도 향상에 좋은 영향을 미쳤다. 반응소결 및 PHIP를 통해 Ti5SI3 -Cu의 상대밀도를 약 99%까지 높일 수 있었으며, 이때 Cu의 효과는 감도지수 부합됨을 확인하였다.

• Journal of the Korean Ceramic Society
• /
• v.38 no.7
• /
• pp.643-647
• /
• 2001

퓨란수지로부터 유리질 탄소를 제조하였다. 유리질 탄소의 제조시, 사용된 수지가 경화 및 탄화 단계에서 많은 양의 가스를 방출하면서 큰 수축이 발생하여 크랙을 형성하고 휨 현상을 일으킨다. 이런 현상을 감소시키기 위하여 본 실험에서는 경화단계에서 압력을 가하고, 가열속도를 매우 느리게 하였다. 또한, 경화단계에서 무게감소와 수축율을 억제하고, 발생하는 가스의 배출을 용이하게 하여 궁극적으로는 시편의 크랙 및 휨 현상을 방지하고자 필러와 알콜을 첨가하였다. 그 결과, 무게감소와 수축을 억제하고 밀도의 증가를 가져왔고 유리질 탄소를 용이하게 제조할 수 있었으나 알코올을 첨가한 경우 필러의 양이 증가할수록 높은 비저항 값과 낮은 강도값을 나타내었다. 이런 현상은 알코올이 경화단계에서 분해 증발하면서 미세한 기포를 형성하고 이것들이 기공으로 전이하여 최종 제품에까지 영향을 주었기 때문이다.

• Nuclear Engineering and Technology
• /
• v.25 no.2
• /
• pp.233-236
• /
• 1993

For one-dimensional two-phase flow without phase change and without axially-temporally rapid change of pressure, the interrelationship between the drift-flux model and the two-fluid model is studied. It is derived on the basis of the fact that the vapor conservation equation is related to the momentum equation by the drift flux. Starting from the two-fluid model, we obtain the interfacial friction expressed in terms of drift-flux parameter. Also, by deriving the void propagation equation, the drift-flux is shown to have jnterrelationship with forces in the two-fluid model.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.211-214
• /
• 2009

Using the numerical code for the interior ballistics, the performance of the interior ballistics with the characteristic of the ignition injection has been investigated. When the maximum position of ignition injection is near the base, the pressure distribution at the chamber of the interior ballistics was uniform and the final projectile velocity is increased.