• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.2
• /
• pp.9-16
• /
• 1999

Edible films were prepared from proteins extracted from soybean curd residue by alkaline extraction and isoelectric precipitation. Effects of film forming solution pH and plasticizers on mechanical and barrier properties of edible films were studied. films were formed within pH $7{\sim}11$ with tensile strength (TS) of $2.9{\sim}3.3$ MPa. Films produced under pH 10 had the highest TS and Elongation (E) (3.3 MPa and 60.1%) but no significant difference was observed among water vapor permeabilities (WVP) of film. Glycerol, sorbitol and its mixture (1:1, w/w) were added as plasticizers. The concentration and mixing ratio of plasticizers also affected the TS, E and WVP of films. TS of films decreased from 15.0 MPa to 2.9 MPa as plasticizer concentration increased from 0.4 to 0.8 g plasticizer/g protein. At a plasticizer concentration, the highest TS was observed when sorbitol was used whereas the highest E was measured when mixture of glycerol and sorbitol was used as plasticizer WVP of films increased as the plasticizer concentration increased. Films plasticized with glycerol showed the highest WVP among the films with the same plasticizer concentrations. Edible films prepared from soybean curd residue protein showed very low oxygen permeabilities ($29.5{\sim}61.1aL{\cdot}m/m^2{\cdot}s{\cdot}Pa$) and oil resistance at all plasticizer concentration level tested.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.3
• /
• pp.243-250
• /
• 2020

The purpose of this study is to find out the possibility of applying microwave-hypochlorous acid leaching to effectively leaching Au in hydrothermal minerals on board. The comparative leaching experiment were confirmed that the leaching rate of Au with(T1)/with out(T2) of microwave nitric acid leaching. In addition, the leaching rate of Au on the conventional leaching by mechanical agitation(T3) and microwave leaching was compared. The result of microwave nitric acid leaching(solid-liquid ratio; 10%, leaching temperature; 90 ℃, leaching time; 20 min) confined that the metal leaching rate was high in the order of As>Pb>Cu>Fe>Zn, and the content of Au in the leaching residue was increased from 33.77 g/ton to 60.02 g/ton. As a result of the comparative leaching experiment using a chloride solvent, the dissolution rate of Au was high in the order of T1(61.10%)>T3(53.30%)>T2(17.30%). Therefore, chloride, which can be manufactured using seawater and that can be recycled by collecting chlorine gas generated in the leaching process, is expected to be an optimal solvent for Au leaching. In addition, the application of microwaves is believed to be effective in terms of time, efficiency and energy.

• The Korean Journal of Mycology
• /
• v.27 no.1 s.88
• /
• pp.10-14
• /
• 1999

A single phase composter was constructed by modifying the conventional mixer of sawdust for the cultivation of oyster mushroom Pleurotus ostreatus. The machine was designed on the basis of 3-phase-1 system which was controlled in prewetting, pasteurization and fermentation processes. In composting 200 kg of straw and cotton waste in the machine, it took 20 minutes in prewetting step and also to hours at $65^{\circ}C$ in pasteurization process. Postfermentation by aerothermophiles was completed by treating the compost at $45^{\circ}C-50^{\circ}C$ for 48 hours which was shorten 24 hours from the conventional method. In the postfermentation at high temperature, forced aeration and/or vigorous mixing process(es) played a great role in the improvement of spawn quality. The growth of mycelium of oyster mushroom was excellent in the culture combinated with 3 parts of surface inoculation and 7 parts of mechanical mixing.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.9-17
• /
• 2010

The LCC (Liquid Cadmium Cathode) structure to be developed for inhibiting the formation and growth of the uranium dendrite has been known as a key part in the electrowinning process for the simultaneous recovering of uranium and TRU (TRans Uranium) elements from spent fuels. A zinc-gallium (Zn-Ga) experimental system which is able to be functional in aqueous condition and normal temperature has been set up to observe the formation and growth phenomena of the metal dendrites on liquid cathode. The growth of the zinc dendrites on the gallium cathode and the performance of the existing stirrer type and pounder type cathode structure were observed. Although the mechanical strength of the dendrites appeared to be weak in the electrolyte and easily crashed by the various cathode structures, it was difficult to effectively submerge the dendrite into the bottom of the liquid cathode. Based on the results of the aqueous phase experiments, a lab-scale electrowinning experimental apparatus which are applicable to the development of LCC srtucture for the electrowinning process was established and the performance tests of the different types of LCC structure were conducted to prohibit the uranium dendrite growth on LCC surface. The experimental results of the stirrer type LCC structures have shown that they could not effectively remove the uranium dendrites growing at the inner side of the LCC crucible and the performances of the paddle and harrow type LCC structure were similar. Therefore a mesh type LCC structure was developed to push down the uranium dendrites to the bottom of the LCC crucible growing on the LCC surface and at the inner side of the crucible. From the experimental results for the performance test of the mesh type LCC structure, the uranium was recovered over 5 wt% in cadmium without the growth of uranium dendrites. After completion of the experiments, solid precipitates of the bottom of the LCC crucible were identified as an intermetallic compound (UCd11) by the chemical analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.9
• /
• pp.895-900
• /
• 2012

This paper aims to examine the effect of nanodroplets on pool-type absorption heat transfer enhancement and to find the relationship between the dispersion stability and the absorption performance. The concentrations of oil and surfactant are considered as the key parameters. $C_{12}E_4$ and Tween20 are used as the surfactants and N-decane oil is added to the $NH_3/H_2O$ solution to make the binary nanoemulsion fluids. Binary nanoemulsion fluids are dispersed by the ultrasonic vibrator and the stirrer under specific conditions. The dispersion stability of binary nanoemulsion fluids for each oil concentrations is evaluated from the droplet size and Tyndall effect analysis. The absorption performance of binary nanoemulsion fluids is compared with the result of dispersion stability. In addition, it is found that the binary nanoemulsion fluid is a strong candidate as a new working fluid for absorption applications.

• Journal of Welding and Joining
• /
• v.29 no.6
• /
• pp.56-64
• /
• 2011

Friction stir spot welding between 5454 aluminum alloy sheets with the different thicknesses of 1.4 and 1.0 mm was performed. In the welding process, the tool for welding was rotated ranging from 500 to 2500, and plunged to the depth of 1.8 mm under a constant tool plunge speed of 100 mm/min. And then, the rotating tool was maintained at the plunge depth during the dwell time ranging from 0 to 7 sec. The pull-out speed of the rotating tool was 100 mm/min. The increase of tool rotation speed resulted in the change of the macrostructure of friction-stir-spot-welded zone, especially the geometry of welding interface. The results of the tensile shear test showed that the total displacement and toughness of the welds were increased with the increase of the tool rotation speed, although the maximum tensile shear load was decreased. However, the change in the dwell time at the plunge depth of the tool did not produce the remarkable variation in the macrostructure and mechanical properties of the welds. In all cases, the average hardness in friction-stir-spot-welded zone was higher than that of the base metal zone. By the friction stir spot welding technique, the welds with the excellent mechanical properties than the mechanically-clinched joints could be obtained.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.9 no.3
• /
• pp.77-87
• /
• 2001

Composting is a cost-effective and environmentally-sound technology to treat soils contaminated with hazardous organic pollutants. Pollutants to be treated are as follows: explosives, phenolic compounds, PAHs, petroleum hydrocarbons, pesticides, and etc. Composting systems are windrow, static pile, and in-vessel. Design and operational parameters of composting are aeration modes, temperature, moisture content, nutrient supplement, amendment added, and etc. Appropriate oxygen concentration of composting for contaminated soils are 5~15%, while some compounds are degraded well at the low $O_2$ concentration of 2~5%. The most diverse microorganisms live in the temperature of $25{\sim}40^{\circ}$. 50~90% of the soil field capacity is the moisture content not to make a problem in composting. Assuming a bacterial chemical equation is $C_{60}H_{87}O_{23}N_{12}P$, theoretical C : N : P from bacterial chemical portion is approximately 20 : 5 : 1. It should be noted that the ratio does not apply to the total organic carbon measured in a waste because not all carbon metabolized by bacteria is synthesized to new cellular material. Initial C/N ratio of 25~40 is optimum. It is more economical to recycle soils or composts than to add commercial microbes.

• Journal of agriculture & life science
• /
• v.52 no.6
• /
• pp.81-88
• /
• 2018

This study analyzed the characteristics of 6 recyclable bulking agents which can replace sawdust and rice hulls that are commonly used in livestock manure composting. The content of all the hazardous chemicals found in the bulking agents used in this experiment was between 0.0 and 34.1 ppm, which was noticeably lesser than the maximum content levels of hazardous substances 5.0~900.0 ppm prescribed by the Rural Development Administration(RDA), which means that the bulking agents would be able to replace sawdusts and rice husks. The water content of the bulking agents ranged from a minimum of 12.4% to a maximum of 16.6% in the original state, which was much less than 60%, the optimal moisture content. These results indicate that they would be able to function fully as bulking agents. Their water absorption rate was in the range of minimum 31.9% ~ maximum 600.0%, which showed huge differences among the types of bulking agents. The most appropriate bulking agent in terms of water absorption rate was wood pellets. It was the highest in the wood briquette manufactured by A, which was followed by C and B in the order. The shear strength of the 5 types of bulking agents in the original state was 271.7 N on an average, the highest figure of all, except for the oak briquette whose shear strength could not be measured and the wood pellets in the absorption state. The shear strength in the dry and absorption states then followed, and were 78.0 N and 27.7 N on an average, respectively. The wood briquette of A recorded considerably lower shear strength than that of B and C. Overall, shear strength tended to increase according to lower water absorption rates. Since pine wood chips and oak cuts have relatively greater shear strength even in the absorbing state than the other materials, they will be able to endure some power in the case of stirring with pig droppings.

• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1529-1535
• /
• 1999

This study was done for the extraction of carotenoid from Phaffia rhodozyma in combination with PEF and other methods. PEF treatment conditions were $30{\sim}80\;kV/cm,\;100{\sim}1000\;Hz\;and\;100{\sim}1000\;{\mu}s$. In order to increase permeability of yeast cell wall, various methods such as freezing-thawing, mechanical treatment, solvents, permeabilizing agents, and yeast cell wall lytic enzyme were used before PEF treatment. The combination of PEF $(50\;kV/cm,\;300\;Hz,\;1000\;{\mu}s)$ and conventional methods such as solvent and freezing-thawing pre-treatment had no effects on the extraction of carotenoid pigments. The extent of extracted carotenoid by the PEF $treatment(50\;kV/cm,\;300\;Hz,\;1000\;{\mu}s)$ combined with yeast cell wall lytic enzyme and mechanical pre-treatment increased 52% and 69.8% more than the sum of that by each treatment, respectively. Permeabilizing agents, especially Tween 20 and capric acid, enhanced the extraction efficiency of carotenoid pigments from P. rhodozyma cells. These results indicated the feasibility for the continuous extracting carotenoid pigments from P. rhodozyma by PEF combined with other permeabilizing methods.

• Journal of the Korean Chemical Society
• /
• v.66 no.2
• /
• pp.78-85
• /
• 2022

Natural white clay was treated with 6 M of H₂SO₄ and heated at 80℃ for 6 h under mechanical stirring and the resulting acid active clay was used as an adsorbent for the removal of Cs⁺ in water. The physicochemical changes of natural white clay and acid active clay were observed by X-ray Fluorescence Spectrometry (XRF), BET Surface Area Analyser and Energy Dispersive X-line Spectrometer (EDX). While activating natural white clay with acid, the part of Al₂O₃, CaO, MgO, SO₃ and Fe₂O₃ was dissolved firstly from the crystal lattice, which bring about the increase in the specific surface area and the pore volume as well as active sites. The specific surface area and the pore volume of acid active clay were roughly twice as high compared with natural white clay. The adsorption of Cs⁺ on acid active clay was increased rapidly within 1 min and reached equilibrium at 60 min. At 25 mg L^- of Cs⁺ concentration, 96.88% of adsorption capacity was accomplished by acid active clay. The adsorption data of Cs⁺ were fitted to the adsorption isotherm and kinetic models. It was found that Langmuir isotherm was described well to the adsorption behavior of Cs⁺ on acid active clay rather than Freundlich isotherm. For adsorption Cs⁺ on acid active clay, the Langmuir isotherm coefficients, Q, was found to be 10.52 mg g^-1. In acid active clay/water system, the pseudo-second-order kinetic model was more suitable for adsorption of Cs⁺ than the pseudo-first-order kinetic model owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal. The overall results of study showed that acid active clay could be used as an efficient adsorbent for the removal of Cs⁺ from water.