• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.50-55
• /
• 1995

진동하는 경계면의 진동장 및 음장을 재구성하기 위하여 음장측정치 및 경계요소법을 이용한 음향 홀로그래피 방법을 연구하였다. 특히, 측정잡음 및 전달행렬의 특이성에 의해 발생하는 재구성 오차에 대하여 고찰하였다. 재구성의 정확도를 나타내기 위하여 전달행렬의 특이인자를 도입하였다. 예제로 한면이 진동하는 직육면체 상자를 고려하였다. 결과로부터 매우 작은 측정잡음에 대해서도 전달행렬의 특이성 재구성 오차가 크게 발생하며, 측정위치에 따라 전달행렬의 특이성이 크게 영향 받음을 확인하였다. EfI방법을 이용하여 최적의 측정점을 선택한 결과 전달행렬의 특이성을 크게 줄일 수 있었으며 이때 측정점의 위치는 가진주파수에 관계없이 큰 음장이 형성되는 소음원의 근접장에 위치함을 알 수 있다. 또한 저주파 가진에 비해 고주파 가진이 작은 특이인자값을 나타내며, 따라서 재구성 오차가 작음을 알 수 있었다. 재구성장의 정밀도를 향상시키기 위하여, 부가적으로 진동장의 norm을 제한하는 적절화방법을 도입하였다. 모델의 최소자승오차를 최소화 하는 최적의 적절화변수를 추정하여 이로부터 재구성 오차를 줄일 수 있었다.

• Journal of KSNVE
• /
• v.7 no.2
• /
• pp.301-310
• /
• 1997

This paper presents active noise control method to form the near-field quiet zone for passengers in an automobile. The actuator model including interior acoustic plant, speaker and amplifier is experimentally identified in forms of auto-regressive and moving average by means of least mean square algorithm, The digital controller is composed of the regulator and Kalman filter to be designed based on LQG (linear quadratic gaussian). If the actuator model is prefiltered with digital filter to be properly designed for concentrating control performance index on the frequency band of primary noise source, LQG design approach can be effectively applied for the design of headset controller. Experimental results demonstrate that near-field quiet zone showing about 10dB noise reduction at microphone position can be formed using the headset located at passenger seat.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.82-84
• /
• 2020

본 논문에서는 용기 소음 저감을 위해 Anyplace induction heating (lH) 시스템에 적합한 설계 방안을 제시한다. 다수의 워킹 코일 및 인버터를 적용한 Anyplace lH 시스템에서 인접한 코일들이 서로 다른 동작 주파수로 용기를 가열 할 경우 주파수 차이에 따른 용기 소음이 발생한다. 따라서 용기의 근접 가열 시 발생하는 소음을 저감하기 위한 방안들을 비교 및 분석하고 실험 및 시뮬레이션을 통해 phase locked loop (PLL)을 이용한 교번 pulse density modulation (PDM) 제어를 적용한 시스템 설계 방안에 대한 타당성을 검증한다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.12
• /
• pp.969-976
• /
• 2014

Nowadays, it is required for naval ships to estimate 3D underwater radiated noise pattern in all direction at peak frequencies of hull vibration for the reduction of being detected and doing the effective operation. For this purpose, the numerical method has to be developed to calculate 3D underwater radiated noise pattern with experimental data. It is very difficult to obtain the experimental data for the real ship. Alternative to get the experimental results is to use NAH(near-field acoustic holography) in acoustic tank with experimental model. Application of NAH in acoustic tank for the experimental model needs some investigation of reflection wave from the wall of the acoustic tank and unmeasured zone of the experimental model due to the supporting structure for it. In this study, the effect of reflection wave in the acoustic tank and unmeasured area of the experimental model when using the NAH was investigated with experiment and numerical model. From these, it is known for the error due to reflection wave can be reduced when the distance between the measurement plane and source is being shorten. Also, unmeasured area of the experimental model gives rise to some error in the estimation of the far-field acoustic pressure.

• Tunnel and Underground Space
• /
• v.16 no.4 s.63
• /
• pp.347-356
• /
• 2006

We analyzed case studies doing in-depth inspection of tunnel to maintain safety of existing tunnel in constructing new tunnel near to a existing tunnel with single track. Futhermore, We accomplished in-depth inspection of existing tunnel and numerical analysis. We suggested remedies to security safety of existing tunnel. We applied line drilling and pre-large hole boring method not to have an effect on existing tunnel and convinced the safety of existing tunnel from blast-vibration and blast-noise of numerical analysis. We planed to install basset system to measure displacement of existing tunnel according to excavating new tunnel.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.10
• /
• pp.785-790
• /
• 2003

This paper presents an approach to optimally design the air-hearing surface (ABS) of the optical flying head for near-field recording technology (NFR) NFR is an optical recording technology using very small beam spot size by overcoming the limit of beam diffraction. One of the most important problems in NFR Is a head disk interface (HDI) issue over the recording band during the operation. A multi-criteria optimization problem is formulated to enhance the flying performances over the entire recording band during the steady state. The optimal solution of the slider, whose target flying height is 50 nm, is automatically obtained. The flying height during the steady state operation becomes closer to the target values than those for the Initial one. The pitch and roll angles are also kept within suitable ranges over the recording band. Especially. all of the all-hearing stiffness are drastically increased by the optimized geometry of the air hearing surface.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.609-612
• /
• 2008

The solid immersion lens (SIL) based near-field recording (NFR) system is considered as one of the high density optical data storage system. For the NFR servo system, tracking servo control is a difficult technology to maintain extremely small gap between SIL and media within one twentieth. This is because the track pitch is decreased for increasing the recording density. In this paper, we propose disturbance observer (DOB) and internal model principle (IMP) for disturbance rejection due to eccentricity of disk. The performance of tracking controller using DOB is increased by about 85%, 94%, 97% using Q filters that have bandwidths of 50Hz, 125Hz, 250Hz, respectively. Moreover, IMP based controller is effectively reduced the residual error.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1528-1532
• /
• 2000

The conventional optics and near field optics are compared numerically in the view points of the spot size and propagation characteristics. The decaying characteristics of near field light require the optics to access the object within several tens of nanometers. Therefore the gap control is one of the main issues in the near field optics area. In this paper the gap control is done by using the shear force of the NF(Near Field) probe and the characteristics are examined. The probe is modeled as a 2'nd order mass-spring-damper system driven by a harmonic force. The primary cause of the decrease in vibration amplitude is due to the damping force - shear force - between the surface and the probe. Using the model, damping constant and resonance frequency of the probe is calculated as a function of probe-sample distance. Detecting the amplitude and phase shift of the NF probe attached to the high Q-factor piezoelectric tuning fork, we can control the position of the NF probe about 0 to 50nm above the sample. The feedback signal to regulate the probe-sample distance can be used independently for surface topography imaging. 3-D view of the shear force image of a testing sample with the period of $1{\mu}m$ will be shown.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.2 s.95
• /
• pp.184-191
• /
• 2005

The near-field scanning micro scope (NSOM) technique is in the spotlight as the next generation storage device. Many different types of read/write mechanism for NSOM have been introduced in the literature. In order for a near-field probe to be successfully implemented in the system, a suitable slider and suspension are needed to be properly designed. The optical slider is designed considering near-filed optics and probe array. The suspension generally supports slider performance, and tracking servo capacity in HDD. Moreover, the suspension for optical slider also should meet the optical characteristics, and is also required to satisfy shock performances for the mobility for the actuator. In this study, the optical slider and the suspension for near-field probe array are designed and analyzed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.393-398
• /
• 2004

The near-field scanning micro scope (NSOM) technique is in the spotlight as the next generation storage device. Many different types of read/write mechanism for NSOM have been introduced in the literature. In order for a near-field probe to be successfully implemented in the system, a suitable slider and suspension are needed to be properly designed. The optical slider is designed considering near-filed optics and probe array. The suspension generally supports slider performance, and tracking servo capacity in HDD. Moreover, the suspension for optical slider also should meet the optical characteristics, and is also required to satisfy shock performances for the mobility for the actuator. In this study, the optical slider and the suspension fer near-field probe array are designed and analyzed.