• Journal of the Korean GEO-environmental Society
• /
• v.19 no.2
• /
• pp.5-12
• /
• 2018

Underground cavities could induce road subsidence, which have been frequently observed in urban areas. Therefore, adequate backfilling materials and the restoring methods of the cavities are required to prevent the road subsidence. The objective of this paper is to evaluate the suitability of backfilling methods using foaming lightweight grouting materials considering the flow values, unit weights, and air contents at slurry and expanded states, and unconfined compressive strengths. The grouting materials consist of water, cement, and foaming agent whose proportions of water, cement, and foaming agent are 25: 25: 1.0 and 25: 25: 1.2. The flow values of the two materials are greater than 200 mm, and their unconfined compressive strengths at 28 days age are smaller than 1.3 MPa. From the results, the two proportions of materials are expected to be effectively used as a backfilling material. However, the material components should be carefully mixed because poor mix of these materials could induce non-homogeneous distribution of air bubbles. The unexpectedly non-homogeneous distribution of air bubbles may induce significant cracks or additional cavities.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.4
• /
• pp.181-189
• /
• 1996

It is well-known that the hearing strength in vertical joints of precast concrete large panel system is affected by grout compressive strength angle of shear key and bearing area. 21 vertical joint specimens were tested to investigate the effects of these parameters The analysis of test results shows that : 1. The higher be grout compressive strength, the higher will shear strength be. And the bearing strength does not so increase in proportion of bearing area. 2. The shear key with the angle of $20^{\circ}$shows the highest bearing strength among three angle variables of $20^{\circ}$, $25^{\circ}$, $30^{\circ}$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.169-177
• /
• 2017

Recently, as the size of transportation vessels has increased, there is a growing need for securing the front-water depths of existing port facilities. The method of deepening front-water depth is securing the depth of the port facility, and it is reinforced by grouting after excavating the rubble-mound to the required depth. The purpose of this study is to investigate the reinforcing performance and filling performance of thixotropic grout as a grouting material for reinforcing rubble-mound. Compressive strength tests were carried out for two types of thixotropic grout, and 5 specimens with a diameter of 400 mm and a height of 530 mm were manufactured and evaluated for filling performance. The required strength of reinforced rubble-mound required to ensure the safety of the structure is 6 MPa. All the thixotropic grouts used in this study were found to satisfy the required strength over 9 MPa at 7 days of age. As a result of visual observation of filling state of the filling performance test specimens, it was confirmed that the thixotropic grout was well filled up to the desired fillet height.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.623-630
• /
• 2007

Grouting materials are used for the unification of superstructural and substructural body like bridge seat (shoe) or machinery pedestal and e.t.c by filling their intercalary voids. Accordingly, grouting materials have been developed and used mainly with products of high strength because those materials are constructed specially in a part receiving large or impact load. In this situation, the structural body constructed by grouting materials with high stiffness-centered (caused by high strength) products is apt to cause brittle failure when receiving over a limit stress and to cause cracks according to cumulative fatigue by continuous and cyclic load. In addition, grouting materials are apt to cause cracks by using too much rapid hardening agents that give rise to high heat of hydration to maintain high strength at early age. In this study, to overcome these problems, cement type grouting materials including powder of waste tire and resin as elastic materials which aim to be more stable construction and to be improvement of mother-body's unification are developed and endowed with properties of high toughness and high durability add to existing properties of high flowability, non-shrinkage and high strength. Besides, this study contribute to of for green construction materials for being possible recycling industrial waste like waste tire and flyash. On the whole, seven type mixing conditions are tested and investigated to choose the best mixing condition.

• Journal of the Korea Concrete Institute
• /
• v.15 no.4
• /
• pp.615-622
• /
• 2003

The purpose of this study is to propose the more reasonable equation of bond strength of grout-filled splice sleeve. To accomplish this objective, total 60 full-sized specimens were tested under monotonic loading. The experimental variables are compressive strength of mortar, embedment length and size of reinforcing bars. Following conclusions are obtained; 1) If the adequacy of existing equations which estimate the bond strength of grout-filled splice sleeve are investigated, they underestimate the bond strength of grout-filled splice sleeve by 8-18%. Also the existing equations have a tendency to underestimate with decrease in the embedment length of reinforcing bars. 2) From the test result of bond failure, the equation which estimates the confining pressure of grout-filled splice sleeve was proposed by making multiple regression analyses of which independent variables are embedment length of reinforcing bars and compressive strength of mortar. This equation predicted the measured bond capacity of this test more accurately than existing equations and eliminated the deviation according to the embedment length of reinforcing bars.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.26-33
• /
• 2014

The study investigates the effects of the type, replacement ratio and method of use of mineral admixtures on the fluidity, bleeding ratio, volumetric change and compressive strength of the grout in order to provide basic data for the development of high-quality grout for PSC bridges. In view of the results relative to the type and replacement ratio of the mineral admixtures, it appears that fly ash has practically no effect on the improvement of the fluidity nor on the reduction of bleeding and shrinkage of the grout. On the contrary, blast furnace slag and silica fume appear to have significant effect on the improvement of the fluidity or on the reduction of bleeding and shrinkage of the grout. With regard to the combined use of mineral admixtures, the combination of fly ash and blast furnace slag provides satisfactory fluidity but with significant increase of bleeding and shrinkage, whereas the combination of blast furnace slag and silica fume reduces bleeding and shrinkage but with large loss of the fluidity. On the other hand, the combination of fly ash and silica fume results in satisfactory fluidity accompanied with fair reduction of bleeding and shrinkage of the grout. In view of these results, the type, replacement ratio and method of use of the mineral admixtures are seen to influence the fluidity, bleeding and volumetric change of the grout. Accordingly, it is necessary to select the mineral admixtures considering these effects for their exploitation in the grout of PSC bridges.

• Explosives and Blasting
• /
• v.27 no.1
• /
• pp.32-37
• /
• 2009

To look over the effect of mixed proportion of cement, sand and water on strength, 162 tests were made for 9 mix proportions. It was observed that strength increased as water in the mixture is reduced. As a result of the control of sand ratio by 50%, the execution strength increased when the sand ratio is raised. Strength was consistent during curing period on each mix proportion, but there were sections where it suddenly increased. Poisson's ratio widely ranged from 0.13 to 0.27, and Young's modulus also broadly ranged from 13.79MPa to 33.25MPa. Poisson's ratio had nothing to do with uniaxial compressive strength, wheras Young's modulus was concerned with it. Young's modulus from theory and experiment showed similar outcome on the 3rd curing day, however, the strength from theory was higher than that from test after 3rd day. In consequence, there was a great change of strength between 3rd and 7th curing day. In addition, it is more efficient to use field strength value between the 3rd and 7th day and to apply Young's modulus on it for determining the exact time.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.4
• /
• pp.25-34
• /
• 2006

Portland cement and sodium silicate are widely used as the main components of the injection, which are used to prevent flow and improve ground condition. The main problem of the injection material is the leaching of the sodium hydroxite and silicate due to the limited reaction with the cement. This paper studies the effect of cement hydration retarder on the compressive strength of the sodium silicate - cement gel. A series of tests, including digital-type testing machine, X-ray diffraction and scanning electron microscope are performed. Results clearly demonstrate that the sodium tripolyphosphate, which is the cement hydration retarder in the test, significantly improves the initial strength of the homogel.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.1
• /
• pp.67-77
• /
• 2019

The grouting method is utilized to reinforce and waterproof poor grounds, enhance the bearing capacity of structures damaged resulting from settlement due to elevation and vibration or differential settlement, and for cutoff. The purpose of this research is to enhance the compressive strength of grout materials by using aramid fiber and develop a high-strength ground improvement method by using blast furnace slag powder. In this regard, this study has conducted a uniaxial compression test after checking the high charge (higher than 50%) of the ratio of blast furnace slag powder and cement at 100:0, 70:30 and 40:60%, adding the aramid mixture based on 0, 0.5 and 1.0% of the cement and furnace slag powder weight and creating sand gels based on surface oiling rate of 0.7 and 1.2%. For the environmental review evaluation, a heavy metal exudation test and a pH test measurement have been conducted. The experiment results showed that 1% increase of aramid fiber led to 1.3 times greater uniaxial compression intensity. As for the hexavalent chrome, a 30% increase in blast furnace slag powder led to approximately 50% decrease in heavy metal exudation. However, the pH test revealed that a 30% increase in blast furnace slag powder resulted in approximately 0.5 increase in pH. Further research on the pH part is needed in the future.

• The Journal of Engineering Geology
• /
• v.28 no.1
• /
• pp.61-67
• /
• 2018

Grouting is reinforcement or cutoff method which uses the hardening agent which is typically represented by portland cement and injected into the ground or the structure. When mixing the cement in powder form with water, the particles tend to cohere each other. Once they cohered, the particle size tends to become larger while injection efficiency becomes lower. This study, in a bid to reduce the cohesion of cement, the screen was set inside the grout mixer so that the cement particles are separated while vibrating them. To validate the effect of vibration screen, comparison test was conducted by using ordinary portland cement, slag cement and micro cement. Viscosity test, bleeding test and grain-size analysis indicated that the characteristics varied significantly after passing through the vibration filter. It is expected that the vibration filter installed inside the grout mixer will reduce the cement cohesion when mixing with water.