• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.108-115
• /
• 2009

The superlattice infrared photodetector (SLIP) with an active layer of 8/8-ML InAs/GaSb type-II strained-layer superlattice (SLS) of 150 periods was grown by MBE technique, and the proto-type discrete device was defined with an aperture of $200-{\mu}m$ diameter. The contrast profile of the transmission electron microscope (TEM) image and the satellite peak in the x-ray diffraction (XRD) rocking curve show that the SLS active layer keeps abrupt interfaces with a uniform thickness and a periodic strain. The wavelength and the bias-voltage dependences of responsivity (R) and detectivity ($D^*$) measured by a blackbody radiation source give that the cutoff wavelength is ${\sim}5{\mu}m$, and the maximum Rand $D^*$ ($\lambda=3.25{\mu}m$) are ${\sim}10^3mA/W$ (-0.6 V/13 K) and ${\sim}10^9cm.Hz^{1/2}/W$ (0 V/13 K), respectively. The activation energy of 275 meV analyzed from the temperature dependent responsivity is in good agreement with the energy difference between two SLS subblevels of conduction and valence bands (HH1-C) involving in the photoresponse process.

• Journal of the Korean Society of Radiology
• /
• v.10 no.6
• /
• pp.443-450
• /
• 2016

In this study, we are using a computer tomography image of the abdomen, as an experimental linear research for the image of the fatty liver patients texture features analysis and computer-aided diagnosis system of implementation using the ROC curve analysis, from the computer tomography image. We tried to provide an objective and reliable diagnostic information of fatty liver to the doctor. Experiments are usually a fatty liver, via the wavelet transform of the abdominal computed tomography images are configured with the experimental image section, shows the results of statistical analysis on six parameters indicating a feature value of the texture. As a result, the entropy, average luminance, strain rate is shown a relatively high recognition rate of 90% or more, the control also, flatness, uniformity showed relatively low recognition rate of about 70%. ROC curve analysis of six parameters are all shown to 0.900 (p = 0.0001) or more, showed meaningful results in the recognition of the disease. Also, to determine the cut-off value for the prediction of disease six parameters. These results are applicable from future abdominal computed tomography images as a preliminary diagnostic article of diseases automatic detection and eventual diagnosis.

• Culinary science and hospitality research
• /
• v.21 no.3
• /
• pp.198-211
• /
• 2015

The following research was done to develop a low calorie muffin that has good taste, as well as nutritional benefit. This was done through adding various nutritional qualities of Makgeolli Lees to muffins. It was found that adding Makgeolli Lees substantially increased the amount of ash, crude protein, crude fiber, and moisture. However, it decreased the amount of crude fat. It was also found that the volume, height, and weight all increased with a lower baking loss rate. Other testing on the hardness, expand chewiness, gumminess, and cohesiveness of the muffins with different amounts of Makgeolli Lees found that more Makgeolli Lees led to a lower hardness and chewiness. However, it did not affect the gumminess. "MLM10" with 10 g of added Makgeolli Lees had a cohesiveness that was significantly different from other samples. The cohesiveness of the other samples was substantially lower. "L-value", or lightness, as well as yellowness, decreased as more Makgeolli Lees was added. On the other hand, "a-value", or redness, increased as more Makgeolli Lees was added. A sensory test proved that Makgeolli Lees added muffins were not preferred over the control group in its color, texture, and overall preference, but was evaluated as "good". However, the Makgeolli Lees added muffins were evaluated better than the control group in the categories of "expanded", "uniformity", and "he size of the pores". Therefore, creating muffins by using Makgeolli Lees instead of fat was proven to be possible, and furthermore proved to be a viable substitute.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.17 no.2
• /
• pp.89-99
• /
• 1997

Although discontinuously reinforced metal matrix composite(MMC) is one of the most promising materials for applications of aerospace, automotive industries, the thermal residual stresses developed in the MMC due to the mismatch in coefficients of thermal expansion between the matrix and the fiber under a temperature change has been pointed out as one of the serious problem in practical applications. There are very limited nondestructive techniques to measure the residual stress of composite materials. However, many difficulties have been reported in their applications. Therefore it is important to establish analytical model to evaluate the thermal residual stress of MMC for practical engineering application. In this study, an elastic model is developed to predict the average thermal residual stresses in the matrix and fiber of a misoriented short fiber composite. The thermal residual stresses are induced by the mismatch in the coefficient of the thermal expansion of the matrix and fiber when the composite is subjected to a uniform temperature change. The model considers two-dimensional in-plane fiber misorientation. The analytical formulation of the model is based on Eshelby's equivalent inclusion method and is unique in that it is able to account for interactions among fibers. This model is more general than past models to investigate the effect of parameters which might influence thermal residual stress in composites. The present model is to investigate the effects of fiber volume fraction, distribution type, distribution cut-off angle, and aspect ratio on thermal residual stress for in-plane fiber misorientation. Fiber volume fraction, aspect ratio, and distribution cut-off angle are shown to have more significant effects on the magnitude of the thermal residual stresses than fiber distribution type for in-plane misorientation.

• Elastomers and Composites
• /
• v.37 no.3
• /
• pp.159-169
• /
• 2002

The improvement of flame retardancy of the foams based on NBR/GTR compounds was conducted by formulating various materials i.e. NBR, GTR, inorganic and phosphorus containing flame retardants, foaming agent, cross-linking agent and activator. The foaming properties, morphology, smoke density and flame retardancy of the specimens were investigated using SEM, LOI tester, smoke density control system and cone calorimeter. The phosphorus containing flame retardant reduces heat release rate, increases the limiting oxygen index and a char formation. The inorganic flame retardant increases the limiting oxygen index and reduces heat release rate with an increased CO yield by char formation, and smoke suppressing effect. The formed char seemed to intercept the oxygen transport and heat transfer into the core area. When the composition ratios of the compounds of NBR/GTR were $100{\sim}80/0{\sim}20 wt.%$, and the ratios of the rubbers/flame retardants were $1/1.55{\sim}3.60 wt.%$, we could developed foams with low heat release rate, high limiting oxygen index($28.0{\sim}39.3$), closed or semi-closed cell of uniformity and reasonable expandability($225{\sim}250 %$).

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.42 no.1
• /
• pp.1-7
• /
• 2016

Highly porous polymethyl methacrylate (PMMA) microspheres impregnated by $TiO_2$ powder were prepared by spray drying method. The particle size and the porosity were controlled by optimizing the co-solvent ratio and the polymer concentration. $TiO_2$ powder was impregnated into the microspheres upto 74.6 wt% content based on the weight of the resultant $PMMA/TiO_2$ microspheres. SEM images showed that $TiO_2$ powder was well distributed throughout the inside of the microsphere. EDX mapping showed that the Ti signal was well detected from every part of the microspheres, which was the evidence of the formation of the $PMMA/TiO_2$ composite. Hg porosimetry result showed that the porosity was found to be over 50% regardless of the $TiO_2$ contents. The final product was found to have high oil-absorbing capacity and great hiding power, both of which are key properties in designing the microsphere materials for make-up cosmetics application.

• Journal of the Korean Magnetics Society
• /
• v.20 no.5
• /
• pp.191-195
• /
• 2010

We have investigated the effect of the removal of an initial oxide layer and the anodization time on the growth of the porous alumina layer. The porous alumina layer was fabricated by two-step anodization process with phosphoric acid. We have observed the changes in the uniformity of the pore structure by varying the removing time of the initial oxide layer after the first anodization with phosphoric acid and chromic acid, and noted that its uniformity improves with the removing time. We have also determined the thickness of the alumina layer after the final anodization process and found that the thickness increases linearly with the anodization time. Under 150 V of anodization voltage with phosphoric acid, the growth rate of the porous alumina layer is determined to be 22.5 nm/min.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.859-866
• /
• 2010

To overcome weak and brittle tensile characteristics of concrete, many studies have been conducted on fiber reinforced concrete (FRC). Recently, high performance fiber reinforced cementitious composites (HPFRCC), which shows strain hardening behavior, has been actively investigated. However, most of the studies focused on the material behavior of HPFRCC itself. Only a few studies have been conducted on the tensile behavior of HPFRCC with steel reinforcement. Therefore, a tension stiffening test for HPFRCC members has been conducted in this study in order to investigate the effect of a reinforcing bar on the tensile behavior of HPFRCC. Tensile stress-strain relationship of HPFRCC has been derived from the tests. The HPFRCC resisted tensile stress continuously from the first cracking to the yield of reinforcing bar. Through the comparison with the tensile behavior of HPFRCC members without a reinforcement, it was shown the tensile strength and capacity of HPFRCC were reduced due to the combined effect of the high shrinkage of HPFRCC, restraining effect of steel reinforcement, and the strain hardening behavior of HPFRCC. It is expected that the tension stiffening test results can be useful for an application of HPFRCC with steel reinforcement as structural members.

• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.376-381
• /
• 2018

The purpose of this study is to investigate and optimize an effectiveness process for the recovery of Pd from the spent Pd/C catalyst by the process of hydrogenation of maleic anhydride over Pd/C. Pd solution recovered from Pd/C catalyst was used to prepare Pd/C catalysts. Their characteristics were compared to those of Pd/C catalyst prepared by using a reagent grade precursor solution. Pd in the spent catalyst was leached by the modified process with dry and wet methods to obtain the high recovery ratio of Pd. The burn-out of carbon in the spent Pd/C catalyst was carried out in the rage of $600-900^{\circ}C$. Pd content of carbonized catalyst was confirmed by XRF and ICP. Pd was extracted from carbonized spent catalysts with acid solutions of 1,2 and 4 M HCl at a leaching temperature of $90^{\circ}C$ for 2 h. The high recovery ratio of Pd was shown as 92.4% that leached in 4 M HCl. Also Pd/C catalysts were prepared by using the leached solution and the reagent grade of $H_2PdCl_4$ as a precursor solution and the characteristics were analyzed by XRD, CO-chemisorption and FE-TEM. As a result, the dispersion of the catalyst prepared by using the leached solution was 34.6%, which was found to be equal to or more than that of the Pd/C catalyst prepared by the reagent grade precursor solution.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.68-74
• /
• 2005

The electrical arc furnace (EAF) classified as a special waste contains many flux components producing melts during a sintering process, so it decreases the sintering temperature and improves the mechanical properties of specimens. Increasing dust content in a clay-dust system brick, however, may cause the fraction defective higher due to the excessive liquid produced. To control the liquid behavior produced during sintering process for the clay-dust system specimens, the $Al_2O_3$ was added and the physical properties were analyzed. The microstructure for the clay-dust system body sintered with $Al_2O_3$ became homogeneous and the overall size of pores decreased. Adding $Al_2O_3$ to clay-dust system body increased the mechanical properties and the temperature of maximum strength increased as much as $50^{\circ}C$, and the apparent density increased and the absorption decreased. The mullite ($3Al_2O_3{\cdot}2SiO_2$) was produced during sintering process by reaction of $Al_2O_3$ and $SiO_2$ which could participate to liquid-producing-process and the viscosity of melts increased which was proved by measuring a critical viscosity temperature (Tcv) therefore, the refractoriness of specimens were improved to lower the fraction defective.