• Food Science and Preservation
• /
• v.14 no.5
• /
• pp.451-456
• /
• 2007

The vitamin C content in extruded comstarch matrix was shown to depend on extrusion process variables (barrel temperature and water content), the packaging method, and the storage period. In addition, loss rates of vitamin C under different processing conditions were calculated. Extrusion process variable were barrel temperature ($80^{\circ}C,\;90^{\circ}C,\;100^{\circ}C$ and $110^{\circ}C$), and water content (25% 30% both w/w). The vitamin C content decreased as barrel temperature increased from $80^{\circ}C$ to $110^{\circ}C$ and water content increased from 25% to 30% when either LDPE plastic film packaging or ON film vacuum packaging were employed. As barrel temperature and water content increased, vitamin C decreased in comstarch packed in either LDPE film or ON film. As temperature increased, vitamin C loss rate increased under both packaging conditions, but the loss tate was only 50% of the LDPE film packaging rate when ON film vacuum packaging was used. In conclusion, the higher the temperature, and the greater the water content, the less vitamin C was inactivated during extrusion cooking, although the loss rah of vitamin C became faster as temperature and water content rose. In conclusion, extrusion process could be applied for making vitamin C matrix to extend vitamin C preservation.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.7
• /
• pp.1109-1113
• /
• 2005

The objective of this study was to determine the effect of extrusion temperature on puffing of white and red ginseng powder. The extrusion variables were feed material (red and white ginseng powder) and die temperature $(100\;and\;115^{\circ}C)$. The analyzed characteristics of ginseng extrudates were sectional expansion index, microstructure and rheological properties. Most of biopolymer was highly puffed at higher extrusion temperature, but the cross-sectional expansion of white and red ginseng powder was higher at 1000e and longitudinal expansion seems to higher at $115^{\circ}C$. White and red ginseng powder were puffed inconsistently and discontinuously at $115^{\circ}C$. The scanning electron microphotograph of extruded white ginseng was uniform air cell distribution at 100oe, but pore size increased at $115^{\circ}C$ and had fine uniformity due to pore explosion. White ginseng and its extrudate were pseudoplastic. Intrinsic viscosity was lower as a result of increased die temperature. The cross-sectional expansion seems to be inconsistent and decreased due to decrease in melt viscosity at $115^{\circ}C$.

• The Korean Journal of Malacology
• /
• v.32 no.4
• /
• pp.297-328
• /
• 2016

This study was performed to know and compare the community structures of macrobenthic invertebrates of five fishing grounds in the coastal waters of Jeju Island from 2013 to 2015. A total of 629 species was identified. Molluscans comprised 282 species (44.8%), Arthropods 88 (14.0%), Poriferans 61 (9.7%), Bryozoans 52 (8.3%) and the others including Cnidarians 51 (8.1%). Density and biomass were estimated to be $71,007ind./m^2$ and $599,208.0gwwt/m^2$, respectively. Gastropods was the most dominant taxon in terms of abundance ($24,625ind./m^2$ ) and number of species as well, and Gastropods was predominant in biomass ($190,789.0gwwt/m^2$). The dominant species were Omphalius pfeifferi, Astralium haematragum, Musculus viridulus, Halosydna brevisetosa, Phascolosoma scolops, Herdmania monus in 5-20 m. Based on the cluster analysis, the study area could be divided into five station groups. The biodiversity, evenness and richness index appeared as follows: H' = 4.28-4.64, E' = 0.74-0.79, R = 33.17-35.45. The dominance index were highest in Sagye and lowest in Sinhung.

• Journal of the Mineralogical Society of Korea
• /
• v.17 no.4
• /
• pp.339-355
• /
• 2004

Locality of domestic high-Ca limestones can be divided into three districts, i.e., (1) the Jecheon-Danyang area, (2) the Samcheok-Taebaek-Jungsun area, and (3) the Uljin-Andong area, in accordance with their geologic background and type of the deposits. Except for some crystalline limestones from the Jecheon-Danyang area, domestic high-Ca limestones were mostly recrystallized and Ca-enriched by the effects of hydrothermal alteration and/or thermal metamorphism. The lime-stones can be also divided into crystalline limestone type, marble type, micro- and mega-crystalline calcite types on the basis of their composition, crystallinity, and mineral facies. An applied-mineralogical characterization of the high-Ca limestones was done through the systematic analyses and tests for the limestones. The high-Ca limestones from the area (1), which are megascopic ally close to the original limestone in lithology, display lower whiteness, higher contents of CaO (51 ～ 54 wt.%), low crystallinity, and fine-grained texture. Two typical hydrothermal types of the high-Ca limestones from the area (2), i.e., micro- (mostly 0.2～0.3 mm) and mega-crystalline (2～15 em) calcite types, have comparatively higher whiteness and rather variable CaO contents (50～55 wt.%) with exhibiting quite different crystallinity each other. The micro-crystalline calcite type is especially dominant in this area, and has comparatively uniform crystallinity and homogeneous composition. Compared to these limestones, the high-Ca limestones from the area (3) show remarkable differences in grade and quality according to their types of deposit and occurrence. Based on these mineral characters and chemical composition, a possible scheme for industrial uses of the domestic high-Ca limestones was suggested.

• Archives of design research
• /
• v.17 no.3
• /
• pp.413-420
• /
• 2004

New design method has been required for web designers to grasp the proper emotion, impression, and feeling of a web site and reflect these elements in web design. It is certain that such a new methodology can be a useful design tool, although web designers have only relied on their intuition and experience to induce users to perceive specific emotion of web sites. In this study, Kansei Engineering Type Ⅰ (Nagamachi, 2002 and Park, 2000) method was applied to develop the methodology. One hundred thirty six web sites believed to convey emotions effectively were first selected by recommendation of professional web designers and twenty two web sites were finally chosen and evaluated using questionnaire. The web sites were then objectively and quantitatively assessed by measuring the degree of utilization of the design elements, balance, overall density, and homogeneity. We examined the cause-and-effect between the results of emotional and quantitative analysis by multiple regression and introduced the design methodology based on the examination. The research method and procedures applied to this study would be applicable to design studies related to the emotional inducement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.229-229
• /
• 2007

나노결정 합금재료를 전력선 통신 커플러용 자심재료로 응용하기 위해서는 고주파 대역에서의 손실 특성이 제어되어야 한다. 즉 고속 전력선 통신을 위한 자심재료의 투자율 및 완화 주파수 등의 전자기적 특성은 30MHz까지 우수하고 안정적으로 유지되어야 하며, 높은 투자율 및 자속밀도, 공진주파수뿐만 아니라 낮은 전력손실 값을 가져야 한다. 따라서 본 연구에서는 나노결점 합금 리본 표면에 딥 코팅, 졸-겔법, 진공함침 등의 방법을 이용하여 PZT, $TiO_2$ 및 $SiO_2$ 등의 산화물 고저항층을 형성시켜 자기적 성질을 유지하면서 고주파 대역의 와전류 손실을 감소시켜 통신용 자심재료로의 응용성을 향상시키고자 하였다. PZT 슬러리의 제타전위 조절을 통해 최적의 분산조건을 얻을 수 있었고, 평균 150nm인 PZT 입자의 초미립자와 가소제, 분산제, 결합제의 첨가조건을 확립할 수 있었다. 딥-코팅은 슬러리 내 유지시간 10초, 인상속도 5mm/min로 30회 반복되었을 때 가정 우수한 특성을 나타내었으며, 고주파 대역에서의 손실 감소효과를 나타내었다. 그리고 졸-겔법에 의해 제조된 슬러리를 이용한 $TiO_2$와 $SiO_2$ 산화물 저항층 코팅을 통해 금속 알콕사이드의 혼합조건 및 저항층 형성용 슬러리의 제조조건을 확립하였고, 합금 리본표면에 균일하고 우수한 점착력을 가지는 저항층을 형성시킬 수 있었으며, 이에 따른 코어손실의 감소효과를 나타낼 수 있었다. 또한 진공 함침법을 통한 저항층 형성에서, $TiO_2$ 나노분말을 표면 저항층으로 코팅했을 때, 가장 높은 코어손실 감소효과를 나타내었다. 한편, 표면 저항층이 형성된 나노결정 합금으로 제조한 자심재료를 이용하여 전력선 통신용 비접촉식 커플러에의 적용과 시험을 통해 고주파 손실 감소효과에 의한 신호전송 특성과 전류특성을 향상시킬 수 있었다.

• Journal of the Mineralogical Society of Korea
• /
• v.18 no.1
• /
• pp.11-17
• /
• 2005

Na-A zeolite were synthesized from melting slag of the incinerated ash by the alkaline activation processes. The experiments were performed in stainless steel vessels, with continuous stirring during the reaction periods. The silica-rich solution, a starting material, which was the waste of crystal growth factory, contains 5.7 wt% SiO₂ and 3.2 wt% Na₂O. And NaAlO₂ was made by the reaction of aluminium dross and NaOH solution and its molar ratios were Na₂O/Al₂O₃= 1.2 and H₂O/Na₂O=9. During the residence time of 7∼8 h at 80℃, the mixing of the silica-rich solution, NaAlO₂ and melting slag yields the production of homogeneous Na-A zeolite. The optimal reactant composition in molar ratio of Na₂O:Al₂O₃:SiO₂ was 1.3∼l.4 : 0.8∼0.9 : 2 and mixing ratio of solution and slag was 1/7∼10 (g/cc). Synthesized Na-A zeolite has cubic form uniformly and its size ranges about 1 ㎛. Ca/sup 2+/ ion exchange capacity of the Na-A was about 180∼210 meq/100g, corresponding approximately 80% to the commercial detergent builder.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.1 s.47
• /
• pp.7-14
• /
• 2006

Melting slag generated from the lots of municipal incineration ash, which causes the one of big urban problems in modern industrial society, was used as starting material for the hydrothermal synthesis of zeolite. P-type zeolite has been successfully synthesized by the combined process of both 'hydrogelation' and 'clay conversion' method. Commercial sodium silicate was used as Si source, and $NaAlO_2$ was prepared by the reaction in a $Na_{2}O/Al_{2}O_{3}$ molar ratio of 1.2. The optimum conditions for zeolite synthesis was found to be the $SiO_{2}/Al_{2}O_{3}$ ratio in the 3.2 and 4.2 range, the $H_{2}O/Na_{2}O$ ratio in the 70.7 and 80.0 range, and more than 15-hour reaction time at $80^{\circ}C$, In the synthesized zeolite, inhomogeneous melting slag particles were disappeared and homogeneous P-type zeolite crystal was grown. The cation exchange capacity of the synthesized zeolite was determined to be approx. 240 cmol/kg.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.36 no.9
• /
• pp.1211-1218
• /
• 2007

The aim of this study was to compare the fermentability and characteristics of fermented broths for white ginseng, red ginseng and extruded white ginseng at $110^{\circ}C$ (A), $120^{\circ}C$ (B) and $130^{\circ}C$ (C). The scanning electron microphotograph of B and C was uniform aircell distribution, but A had increased pore size and exploded some aircell's wall. Saccharification rate constant of C was the highest (10.123 $mg/mL·hr^{1/2}$). Fermentation temperature was $27^{\circ}C$ for 30 days and the cultivation was fixed with Saccharomyces cerevisiae, Aspergillus usamii, and Rhizopus japonicus. The pH of red ginseng fermented broth was 3.79, which was the highest among the fermented samples. The fermented broth of B had the highest acidity (4.46%). The fermented broth of A had the highest reducing sugar content in ginseng suspensions (32.36 mg/mL). In ginseng fermented broths, reducing sugar content was decreased rapidly during the initial 5 days and alcohol content was increased during the initial 5 days. On the fifth day, the fermented broth of C showed the highest alcohol content (5.20%).

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.193-198
• /
• 2014

Lens and DVD require high quality of optical property. Conventional injection molded products contain high residual stress and this invokes birefringence since high cavity pressure and high temperature variation are involved in a molding process. Thus these products are often molded by injection compression molding in order to minimize the residual stress through reducing cavity pressure and uniform cavity pressure. In this study, molding parameters affecting molding quality such as property uniformity in injection compression molding were investigated through experiment. Molding quality deviations among the cavities in multi-cavity mold were also studied. Transparent resins, PC and PS were used in this study. Compression gap, compression speed, compression force, and compression delay time for processing variables in injection compression molding were applied in experiment. Compression force, compression delay time, and compression gap significantly affected the optical property of product. The degree of influence of process variable on the product quality was different in different resins. This implies that the optimal operational conditions in injection compression molding existed for each resin according to flow property.