• Korean Journal of Materials Research
• /
• 제8권4호
• /
• pp.283-287
• /
• 1998

구미와 일본에서는 균열이 실린더벽을 과통하므로서 발생되는 일부누설로 인하여 실린더가 불안전 파괴가 이루어진 후 급속파단으로 전개되는 판당전 누설(Leak Before Break, LBB)를 전제로 한 구조건전성의 확인 시험연구가 널리 수행되고 있다. 본고에서는 Gs-C25 실린더의 구조건전성을 LBB개념의 도입과 파괴역할을 이용하여 평가하였다. 내부압력 80bar일때의 실린더에서 응력확대계수 계산은 구조물의응력확대계수가 극단적으로 큰 디멘젼을 지닌 측균열인 경우에서만 재료의 인성계수 $K_{lc}$ /와 $K_{eff}$ 에 도달된다는 것을 나타내었으며, 반면에 원주균열은 파괴 인성치 $K_{lc-}$ 와 $K_{eff-}$ 값까지는 어떠한 경우에도 도달되지 않았다. 구조물의 국부적인 취성파괴는 균열을 함유한 누설로 유도되는 범위에서, "$K_{1}$ 구조물$\geq$$K_{lc}$ 및 $K_{eff}$ "의 조건을 만족시에만 발생되며, 이는 축균열이 원주균열보다 훨씬 더 위험하다는 것을 증명한다.는 것을 증명한다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제16권10호
• /
• pp.7053-7060
• /
• 2015

The use of FRP(Fiber-reinforced polymer) bars results in larger crack widths under service load due to the generally low elastic modulus and poor bond characteristics of FRP as compared with steel reinforcing bars. The work presented herein includes the results from 12 beams composed of nine rectangular beams and three T-beams reinforced with FRP bars tested under four-point bending. It was investigated that the bond coefficient, $k_b$ in ACI 440.1R-06 equation had high variability which the coefficient of variation was 40% in the range of 0.6 to 1.88 with average 1.05.

• Explosives and Blasting
• /
• 제19권1호
• /
• pp.85-92
• /
• 2001

본 논문에서는 암굴착시 발파에 의한 암반사면의 균열방지 및 사면안정 재고를 위하여 대 구-포항간 고속도로 건설현장에서 시험발파를 실시하고 그 결과를 분석하여 천공깊이별 안전 발파패턴을 제시하였다. 또한 현지 탄성파 속도를 측정하여 발파에 의해 암반에 미치는 균열상태를 조사한 결과 탄성파속도의 감소가 40 ∼ 53%로서 암반 중에 균열을 발생시킨 것으로 나타났다. 발파진동 계측결과를 분석하여 암반에 균열을 일으킬 수 있는 진동속도 기준을 설정하여 균열권 범위를 추정하였으며 사면의 기하학적 형상을 고려하여 손상대를 최소화 할 수 있는 적정 안전설계 패턴을 제시하였다.

• Journal of Korean Society of Steel Construction
• /
• 제15권5호통권66호
• /
• pp.475-487
• /
• 2003

This study developed an analysis model of estimating fatigue damage using the linear elastic fracture mechanics method. Stress history occurring to an element when a truck passed over a bridge was defined as block loading and crack closure theory explaining load interaction effect was applied. Stress range frequency analysis considering dead load stress and crack opening was done. Probability of stress range frequency distribution was applied and the probability distribution parameters were estimated. The Monte Carlo simulation of generating the probability various of distribution was performed. The probability distribution of failure block numbers was obtained. With this the fatigue reliability of an element not occurring in failure could be calculated. The failure block number divided by average daily truck traffic remains the life of a day. Fatigue reliability analysis model was carried out for the welding member of cross beam flange and vertical stiffener of steel box bridge using the proposed model. Consequently, a 3.8% difference was observed between the remaining life in the peak analysis method and in the proposed analysis model. The proposed analysis model considered crack closure phase and crack retard.

• Journal of Korean Society of Steel Construction
• /
• 제14권6호
• /
• pp.773-782
• /
• 2002

In this study, a series of fatigue tests are performed in order to estimate quantitatively the characteristics of fatigue crack growth rate according to the base metal, heat affected zone(HAZ) and weld metal, and the welding method and grade of strength of object steels, and the influence on fatigue crack growth rate according to the direction of welded line for high strength steels of SM570, POSTEN60, and POSTEN80 steels. From the fatigue test results, the retardations of fatigue crack growth rate are remarkable in case that the direction of notch is parallel to welded line than in case that the direction of notch is perpendicular to welded line because of compresive residual stress in weld metal & HAZ. And the characteristics of fatigue crack growth rate according to welding method are that the dispersion of fatigue crack growth rate in case of FCAW method is smaller than that of SAW method. Also, it knows that the fatigue crack growth rate converges in high stress intensity factor range. Meanwhile, fatigue safety is guaranteed sufficiently in the object steels because the fatigue crack growth rate in the range of fatigue crack propagation has a similar tendency to the test results & existing results.

• Journal of the Korean Society for Nondestructive Testing
• /
• 제23권3호
• /
• pp.212-219
• /
• 2003

This study is to evaluate the characteristics of SCC at the welded region of high strength steel using acoustic emission(AE) method. Specimens were loaded by a slow strain rate method in synthetic seawater and the damage process was monitored simultaneously by AE method. Corrosive environment was controlled using the potentiostat, in which -0.8V and -1.1V were applied to the specimens. In the case of one-pass weldment subjected to -0.8V, much more AE counts were detected compared with the PWHT specimen. It was verified through the cumulative counts that coalescence of micro cracks and cracks for the one pass weldment with -0.8V were mostly detected. In case of the one pass weldment subjected to -1.1V, time to failure became shorter and AE counts were produced considerably as compared with that of the two pass weldment. It was shown that AE counts and range of AE amplitude have close relations with the number and size as well as width of the cracks which were formed during the SCC.

• Journal of the Korea Concrete Institute
• /
• 제14권2호
• /
• pp.231-238
• /
• 2002

Dry shrinkage md temperature change cause to develope concrete bridge decks on main girders have initial unidirectional cracks in longitudinal or transverse direction. As they receive traffic loads, the crack gradually propagate in different directions depending on the concrete dimension and reinforcement ratio. Since existing equations that predict crack width are mostly based on the one directional bond-slip theory, it is difficult to determine the actual crack width of a bridge deck with varying the spacing of rebar or strengthening material and to estimate the improvement rate in serviceability of the strengthened bridge deck. In this study, crack propagation mechanism is identified based on the test results and a new crack prediction equation is proposed for evaluation of serviceability. Although more accurate results are derived using the proposed equation, the extent of error is increased as the strain of the rebar or the strengthening material increases after the yielding of rebar Therefore, further research is required to better predict the crack width after the rebar yields under fatigue loading condition.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2009년도 학술대회 초록집
• /
• pp.155-159
• /
• 2009

Crack-controlled method which utilizes the dynamic energy such as explosives and propellent gases have been applied to the development of mineral resource and oil and civil engineering. It is necessary to consider the fracture processes associated with the material properties and external forces to control crack propagation using borehole pressure. To investigate the influence of the applied borehole pressure waveform on the crack propagation in rock masses having different material properties, a no-free surface model was used, consisting of a borehole in rock with a continuous boundary. Loading rates ranging from 1 to 100MPa/${\mu}s$ with different rock mass properties was employed to investigate the loading rate dependency of fracture patterns in the rock mass.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제14권3호
• /
• pp.381-390
• /
• 2001

In this paper, a new improved crack analysis technique by Element-Free Galerkin(EFG) method is proposed, in which the singularity and the discontinuity of the crack successfully described by adding enrichment terms containing a singular basis function to the standard EFG approximation and a discontinuity function implemented in constructing the shape function across the crack surface. The standard EFG method requires considerable addition of nodes or modification of the model. In addition, the proposed method significantly decreases the size of system of equation compared to the previous enriched EFG method by using localized enrichment region near the crack tip. Numerical example show the improvement and th effectiveness of the previous method.

• Journal of Korea Foundry Society
• /
• 제41권5호
• /
• pp.419-433
• /
• 2021

Al-Si-Cu alloys benefit from the addition of copper for better hardness and strength through precipitation hardening, which results in remarkably strong alloys. However, the addition of copper expands the solidification range of Al-Si-Cu alloys, and due to this, these alloys become more prone to hot tearing, which is one of the most common and serious fracture phenomena encountered during solidification. The conventional evaluation method of the hot tearing properties of an alloy is a relative and qualitative analysis approach that does not provide quantitative data about this phenomenon. In the present study, the mold itself part of a device developed in Instone et al. was partially modified to obtain more reliable quantitative data pertaining to the hot tearing properties of an Al-Si-Cu casting alloy. To assess the influence of Cu element, four levels of Cu contents were tested (0.5, 1.0, 3.0, and 5.0 wt.%) in the Al-Si-Cu system alloy and the hot tearing properties were evaluated in each case. As the Cu content was increased, the hot tearing strength decreased to 2.26, 1.53, 1.18, and 1.04 MPa, respectively. At the moment hot tearing occurred, the corresponding solid fraction and solidification rate decreased at the same temperature due to the increase in the solid-liquid coexistence range as the Cu content increased. The morphology of the fracture surfaces was changed from dendrites to dendrites covered with residual liquid, and CuAl₂ phases were observed in the vicinity of hot tearing.