• 터널과지하공간
• /
• 제6권3호
• /
• pp.245-249
• /
• 1996

In this study, the flow field and the recirculation phenomena are investigated numerically for the model around a tunnel entrance and exit. It turns out that the air entering to the tunnel entrance comes mostly from the upper region of the entrance implying that maintaining the air clear in that region is important for the inside-tunnel ventilation. We also found that the recirculation of the exhaust gas from the exit to the entrance has a maximum effect when the flow velocity at the exit is somewhat lower than that of the entrance.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.218-224
• /
• 2011

A supersonic inlet at angle of attack has anti-symmetric pressure distribution, and it can make flow instability and structural problem. In this study, numerical analysis of three-dimensional inviscid flow was conducted under various throttle ratio and angle of attack conditions. Throttle ratio was defined as the ratio of the exit area to the smallest cross section area at inlet, and the ratio is controlled from 0 to 2.42. At various angle of attack, the characteristics of steady and unsteady flow around supersonic inlet is observed under different throttling ratios. From these results, pressure recovery curves and pressure history curves were plotted by post processing. Using pressure history data, FFT analysis is also carried out. Through these processes, it shows the tendency of pressure distribution anti-symmetricity and changing dominant frequency as increasing angle of attack.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.597-600
• /
• 2002

In general, the function of intake structure, whether it be a open channel, a fully wetted tunnel, a sump or a tank, is to supply an evenly distributed flow to a pump station. An even distribution of flow, characterized by strong local flow, can result in formation of surface or submerged vortices, and with certain low values of submergence, may introduce air into pump, causing a reduction of capacity and efficiency, an increase in vibration and additional noise. Uneven flow distribution can also increase or decrease the power consumption with a change in total developed head. To avoid these sump problems pump station designers are considered intake structure dimensions, such as approaching upstream, baffle size, sump width, width of pump cell and so on. From this background, flow characteristics of intake within sump are Investigated numerically to obtain the optimal sump design data. The sump model is designed in accordance with HI code.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.497-501
• /
• 2000

Flow over a sphere is controlled experimentally at $Re=10^5$ using electro-magnetic actuators. The electro-magnetic actuator developed in this study is composed of the permanent magnet electro-magnet membrane and slot. Eight actuators are placed inside the sphere at equally spaced intervals on a latitudinal plane and the position of the control slot is 76 from the stagnation point. Each actuator generates a periodic blowing and suction through the slot at variable frequencies of $10{\sim}140Hz$ and variable amplitudes by controlling electric signals applied to the electro-magnet. Drag on the sphere measured using a load cell is significantly reduced with control at the forcing frequencies larger than the natural shedding frequency $({\approx}14Hz\;at\;Re=10^5)$, whereas drag is slightly increased at the forcing frequency of 10Hz. It is shown from pressure measurement that the static pressure in the rear surface of the sphere is significantly increased with control, indicating that the separation is delayed due to control. Flow visualizations also show that the detaching shear layer is more attracted to the sphere center with control, the separation bubble size is significantly reduced, and motion inside the bubble is very weak, as compared to the case of uncontrolled flow.

• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2136-2149
• /
• 1992

본 연구에서는 Gebhart등이 제시한 새로운 밀도식을 사용하여 경사진 등온평 판이 저온의 순수물속에 잠겨있을 때의 자연대류현상을 F.D.M 방법을 사용하여 수치해 석하였다. 이러한 수치 계산으로부터 등온 평판 주위의 속도, 온도분포 및 평균 누 셀트수를 각각 구하고, 주위물 온도 및 평판의 경사각이 등온 평판에 의한 유동 및 열 전달 현상에 미치는 영향을 구명하였다.또한 본 연구결과와 Riu등이 상사해석하여 구한 다중 정상 상태 영역에서의 결과들과 실험적 연구의 결과들을 상회 비교분석하였 다. 여기서 사용한 등온 평판은 기존의 연구들에서 많이 이용하고 있는 가장 이상적 인 등온면인 0.deg. C 얼음면을 택하였다.

• 대한조선학회논문집
• /
• 제35권4호
• /
• pp.1-10
• /
• 1998

본 논문에서는 비압축성 Newtonian 점성유동에서 초기에 순간 출발하는 2차원 실린더 주위의 유동을 해석하기 위해서, 와도를 기저로 한 수치해석기법을 제안하고 있다. Helmholtz 분리 형태로 표현된 Navier-Stokes방정식에서 유도되는 와도전달방정식과 압력방정식, 그리고 벡터등식에서 유도되는 속도-와도 관계식을 이 문제의 지배방정식으로 택하고, 경계조건으로는 물체표면에서 와도와 압력의 연성관계와 힘의 평형을 고려한 동적와도경계조건과 동적압력조건이 제시된다. 이 지배방정식과 경계조건을 수치적으로 처리하기 위하여, 와도와 압력이 연성되어 있는 경계조건은 Wu등(1994)이 제안한 대로, 연성관계를 유지한 채로 식을 분리하는 방법을 이용하였고, 와도전달 방정식은 유한체적법으로 계산하였으며, 그 식에 포함된 대류항을 처리하는 방법으로 TVD 방법을 이용하였다. 속도는 Biot-Savart적분항이 포함된 벡터등식에서 panel방법으로 구하고, 압력방정식은 형태가 Poisson방정식이므로 역시 panel방법을 이용하였다. 계산에 사용된 격자로 정규격자를 이용하고, 결과를 다른 수치적, 해석적 결과와 비교하여 그 타당성을 검증하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2753-2756
• /
• 2007

In the present study, we reduce the drag and lift fluctuations of the sphere by providing a linear proportional control. For this purpose, we measure the radial velocity along the centerline in the wake and provide blowing and suction at a part of sphere surface based on the measured velocity. Zero-net mass flow rate is satisfied during the control. This control is applied to the flow over a sphere at Re=300 and 425. We vary the sensing location at $0.8d{\leq}X_s{\leq}1.3d$ and find that the most effective sensing region coincides with the location at which minimum correlation between the lift and sensing-velocity directions occurs. As a result, the lift and drag fluctuations are significantly reduced.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2005년도 추계학술대회 논문집
• /
• pp.50-53
• /
• 2005

The turbulent flow around a sphere was investigated in a streamwise meridian plane using two experimental techniques: smoke-wire flow visualization in wind tunnel at Re=5,300 and PIV measurements in a circulating water channel at Re=7,400. The smoke-wire visualization shows flow separation points near an azimuthal angle of $90^{\circ}$, recirculating flow, transition from laminar to turbulent shear layer, evolving vortex roll-up and fully turbulent eddies in the sphere wake. In addition, the mean flow pattern extracted by particle tracing method in water tunnel at Re= 14,500 reveals two distinct comparable toroidal(not closed) vortices in the recirculation region. The mean velocity field measured using a PIV technique demonstrates the detailed wake configuration of close symmetric recirculation and near-wake configuration with two toroidal vortices, reversed velocity zone and vorticity contours.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.183-190
• /
• 2009

The objective of this study is to get simulation data about pulsatile flow around an interior solid body inside a bifurcated tube. All the processes were based on CFD method, with a commercial FVM code, SC/Tetra ver. 6.0 for solving, and with CATIA R16 for generating geometries. The bifurcated tube models were drawn with the bifurcated angle of 45 degrees, considering Murray's law about the diameter ratio. With various locations of the object, the effects of flow on the drag were considered. For the pulsating flow condition, the velocity wave profile was given as the inlet boundary condition. To validate all the result, the simulation was compared with the existing data of the other papers first. Overall flow field of both data were similar, but there was some difference at a zero velocity. Therefore the next simulation was continued with the sine wave profiles where there is no negative flow, and then the data was compared with one of the pulmonary artery velocity where there is negative flow. The final process was to calculate flow variables such as the wall shear stress (WSS) and to compute the drag of the solid object.

• 대한조선학회논문집
• /
• 제45권4호
• /
• pp.379-388
• /
• 2008

A hybrid Cartesian/immersed boundary code is expanded to simulate flow field around a three-dimensional body which undergoes large dynamic deformation. Immersed boundary nodes are automatically distributed based on the edges crossing triangles on body boundary. Velocity vectors are reconstructed at those immersed boundary nodes along local normal lines to the boundary. The reconstruction of pressure is avoided using the hybrid staggered/non-staggered grid method. The developed code is validated through comparisons with other results on laminar flow over a sphere. The code is applied to simulate flow around a foil which is attached to a body of revolution and rotates under periodic deformation. The periodic variation of the tip vortex is observed and the effects of the deformation on hydrodynamic force acting on the body are investigated.