• Journal of the Korean institute of surface engineering
• /
• v.40 no.1
• /
• pp.11-15
• /
• 2007

Stable metallic Cu/Zn nanoparticles were prepared in the base oil phase by hydrothermal method. The physical properties, such as crystal structure, crystallite size and crystallinity according to synthesis conditions have been investigated by XRD, FT-IR and TEM. In addition, 4-ball test has been performed in order to investigate the frictional wear properties of prepared nanosized Cu/Zn particles. The peaks of the X-ray diffraction pattern indicate that the particle size was very small and crystallinity of Cu/Zn particles was good. The micrographs of TEM showed that nanosized Cu/Zn particles possessed a spherical morphology with a narrow size distribution. The crystallite size of the Cu/Zn particles synthesized in base oils was 23-30 nm. It was found that the antiwear capacity increases with increasing Cu/Zn concentration. When the concentration of Cu/Zn was 5.0 wt%, the wear scar diameters was 0.38 mm.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.86-86
• /
• 2017

고효율의 에너지 변환 및 친환경적인 이점들을 이유로, 고분자전해질 연료전지(PEMFC)는 차세대 에너지 장치로 이목을 끌어왔다. 반면, 값비싼 백금 촉매의 이용은 연료전지의 상업적 이용에 주요한 결점으로 작용했다. 최근, Zelenay와 연구팀은 폴리아닐린-철-탄소 복합체구조에서 산소환원활성이 백금과 견주어 비슷한 성능을 낼 수 있음을 보고 하였다. Dodelet은 이러한 높은 성능이 전이금속의 영향에 의한 것일 수 있다는 주장을 하였다. 본 연구팀은 지난 연구에서 제일원리전산모사를 통해 니켈, 코발트, 구리등과 같은 전이금속이 질소가 도핑된 탄소 그래핀층에 미치는 거동을 밝혔다. 결론적으로, 금속들은 질소가 도핑된 그래핀의 전자구조를 바꿀 수 있고, 이러한 전자구조의 변화는 산소 환원반응에서 긍정적으로 작용할 수 있음을 확인하였다. 이러한 이론적 연구에 기반하여, 탄소층으로 감싼 금속은 내구성과 활성을 동시에 보유한 향후 전망있는 촉매 물질로 예상되어진다. 특히, 질소가 도핑된 탄소층으로 코팅된 철-코발트 합금은 계산을 통해 산소환원반응에서 우수할 것으로 예측되었다. 본 연구팀은 FeCo@N-C 나노입자를 직접 합성하였고, 이 촉매의 우수한 활성을 전기화학적, 구조적 관점에서 1) 질소의 도핑 효과, 2) 탄소의 두께 효과, 3) 합금효과에 집중하여 분석하였다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.134-134
• /
• 2016

The effect of different thermal treatments on the sub-50 nm copper nanoparticles is examined in the aspects of chemical, electrical and surface morphology. The copper nanoparticles are chemically synthesized and fabricated for paste-type solution. Simple bar coating method is practiced as a deposition process to form copper thin film on a typical slide glass. Deposited copper thin films are annealed by two different routes: general tube furnace with 99.99 % Ar atmosphere and selective laser sintering process. The thermal behavior of the different thermal-treated copper thin films is compared by SEM, XRD, FT-IR and XPS analysis. In this study, the laser sintering process ensures low annealing temperature, fast working speed and ambient-accessible route. Moreover, the laser-sintered copper thin film shows good electrical property and enhanced chemical stability than conventional thermal annealing process. Consequently, the proposed laser sintering process can be compatible with plastic substrate for flexible applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.2
• /
• pp.121-125
• /
• 2014

In this research, nanocomposite layers consisting of poly (3,4,-ethylene dioxythiophene):polystyrene sulfonic acid (PEDOT:PSS) and CuO nanoparticles were investigated as hole transport layers in organic solar cells based on poly (3-hexylthiophene) (P3HT) as the electron donor and (6.6) phenyl-C61-butyric acid methyl ester (PCBM) as the electron acceptor. The addition of CuO nanoparticles to PEDOT:PSS layer improved the solar cell performance with 0.5% CuO nanoparticle concentration. At optimized concentration, CuO mixed PEDOT:PSS films had good electrical ($4.131{\Omega}{\cdot}cm$) and optical (transmittance > 90%) properties for using hole transporting layer. We investigated that improved solar cell performance with CuO nanoparticles mixed PEDOT:PSS films.

• Korean Journal of Metals and Materials
• /
• v.49 no.12
• /
• pp.950-955
• /
• 2011

In the present study, the formation of hollow Cu oxide nanoparticles through the oxidation process at temperatures from 200 to $300^{\circ}C$ has been studied by transmission electron microscopy with Cu nanoparticles produced by the plasma arc discharge method. The Cu nanoparticles had a thin oxide layer on the surface at room temperature and the thickness of this oxide layer increased during oxidation in atmosphere at $200-300^{\circ}C$ However, the oxide layer consisted of $Cu_2O$ and CuO after oxidation at $200^{\circ}C$ whereas this layer was comprised of only CuO after oxidation at $300^{\circ}C$ On the other hand, hollow Cu oxide nanoparticles are obtained as a result of vacancy aggregation in the oxidation processes, resulting from the rapid outward diffusion of metal ions through the oxide layer during the oxidation process.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.4
• /
• pp.317-322
• /
• 2017

When the heat flux on the heating surface following changing heat condition in the boiling heat transfer system exceeds critical heat flux, the critical heat flux phenomenon is going over to immediately the film boiling area and then it is occurred the physical destruction phenomenon of various heat transfer systems. In order to maximize the safe operation and performance of the heat transfer system, it is essential to improve the CHF(Critical Heat Flux) of the system. Therefore, we have analysis the effect of improving CHF and characteristics of heat transfer following the nanoparticle coating thickness. As the results, copper nanocoating time are increased to CHF, and in case of nano-coatings are increased spray-deposited coating times more than in the fure water; copper nanopowder is increased up to 6.40%. The boiling heat transfer coefficients of the pure water are increased up to 5.79% respectively. Also, the contact angle is decreased and surface roughness is increased when nano-coating time is increasingly going up.

• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.695-701
• /
• 2013

To understand how reactivity between reinforcing nanoparticles and aqueous solution affects electrodeposited Cu thin films, two types of commercialized cerium oxide (ceria, $CeO_2$) nanoparticles were used with copper sulfate electrolyte to form in-situ nanocomposite films. During this process, we observed variation in colors and pH of the electrolyte depending on the manufacturer. Ceria aqueous solution and nickel sulfate ($NiSO_4$) aqueous solutions were also used for comparison. We checked several parameters which could be key factors contributing to the changes, such as the oxidation number of Cu, chemical impurities of ceria nanoparticles, and so on. Oxidation number was checked by salt formation by chemical reaction between $CuSO_4$ solution and sodium hydroxide (NaOH) solution. We observed that the color changed when $H_2SO_4$ was added to the $CuSO_4$ solution. The same effect was obtained when $H_2SO_4$ was mixed with ceria solution; the color of ceria solution changed from white to yellow. However, the color of $NiSO_4$ solution did not show any significant changes. We did observe slight changes in the pH of the solutions in this study. We did not obtain firm evidence to explain the changes observed in this study, but changes in the color of the electrolyte might be caused by interaction of Cu ion and the by-product of ceria. The mechanical properties of the films were examined by nanoindentation, and reaction between ceria and electrolyte presumably affect the mechanical properties of electrodeposited copper films. We also examined their crystal structures and optical properties by X-ray diffraction (XRD) and UV-Vis spectroscopy.

• Korean Journal of Metals and Materials
• /
• v.48 no.12
• /
• pp.1130-1135
• /
• 2010

Cu/carbon nano-particle hybrids were fabricated through the cathodic electrophoretic deposition (EPD) process. CNT and CNF nano-particles were modified to give positive charges by polyethyleneimine (PEI) treatment before depositing them on the substrate. Since a Cu plate was used as an anode in the EPD process, Cu particles were also deposited along with the carbon nano-particles. Experimental observation showed the nano-hybrids constructed a novel formicary-like nano-structure which is strong and highly conductive. Utilizing the hybrids, carbon fiber composites were manufactured, and their electrical conductivity and interlaminar shear strength were measured. In addition, the deposition morphology and failure surface were examined by SEM observations. Results demonstrated that the electrical conductivities in the through-the-thickness direction and the interlaminar shear strength significantly increased by 350~2100% and 14%, respectively.