• 한국소음진동공학회논문집
• /
• 제14권1호
• /
• pp.10-16
• /
• 2004

There are a lot of roots of errors in a motion of the optical pick-up actuator being one of the most significantcomponents in a CD-ROM drive. Most of the studios recently performed have a tendency to seek for the causes from an actuator itself. This paper presents dynamic characteristics of an actuator affected by the motion of a feeding deck. The feeding system is modeled as a rigid body with eight degree-of-freedom. Using Largrange's equation, we derive linear equations of motion with respect to the rectangular coordinate. We found that the ranges of the natural frequencies of a feeding deck and the actuator are close to each other. The time responses are also computed by the Newmark method and Runge-Kutta method. The result show that it is important effect to consider feeding deck in modeling and designing an optical pick-up.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.89-96
• /
• 2006

In this study, fabrication of the large area silicon mirror is accomplished by anisotropic wet etching using micromachining technology for implementation of integrated slim optical pickup and the process condition is also established for improving the mirror surface roughness. Until now, few results have been reported about the production of highly stepped $9.74^{\circ}$ off-axis-cut silicon wafers using wet etching. In addition rough surface of the mirror is achieved in case of tong etching time. Hence a novel method called magnetorheolocal finishing is applied to enhance the surface quality of the mirror plane. Finally, areal peak to valley surface roughness of mirror plane is reduced about 100nm in large area of $mm^2$ and it is applicable to optical pickup using infrared wavelength.

• 소음진동
• /
• 제8권2호
• /
• pp.346-352
• /
• 1998

This paper presents actuating characteristics of an asymmetric high-speed optical pick-up fine actuator that can be installed in a small area such as a notebook personal computer. In the asymmetric actuator four points (mass center, actuation center, supporting point of wire suspension on a bobbin, and optical axis) are not coincident so that the proposed actuator suspension reveals undesirable suspension resonance in the pitch and yaw direction. Lumped parameter dynamic model in each direction is used to investigate the driving characteristics with respect to relative location of the four points. Some of desired design directions toward reducing resonance peaks are suggested by using sensitivity information. In order to avoid undesirable resonance, at least supporting point on the obbin must be located in the middle of the mass and actuation center of the asymmetric pick-up actuator.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.92-97
• /
• 2002

There are a lot of roots of errors in an motion of the optical pick-up actuator being one of the most significant components in a CD-ROM drive. Most of the studies recently performed have a tendency to seek for the causes from an actuator itself. This paper present the dynamic characteristics of an actuator affected by the motion of a feeding deck. The feeding system is modeled as a rigid body with eight degree-of-freedom. Using Largrange's equation, we derive the linear equations of motion with respect to the rectangular coordinate. We found the fact that the ranges of the natural frequencies of a feeding deck and an actuator are close to each other. And the time responses are also computed by the Newmark method and Runge-Kutta method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.618-621
• /
• 2001

The proposed lever actuator has no friction and mass balance characteristics in motion, which are adapt to high-speed and high-density optical disk system. This paper discussed about the theoretical analysis of the lever structure. The modeling of the lever actuator is found. Using the Newton's method, the motion of equation is deduced through the constraint equations and equilibrium equations in three directions (focusing, tracking and tilting). From the above analysis, we know that the shape of the hinge is the very important parameter on determining the performance of the lever actuator, and the actuator has the 2nd order system characteristics. And the first resonant frequency in transmissibility is dependent to the rigidity of the lever while the first transmissibility resonance of conventional actuators is dependent to the first natural resonance of those actuators. This means that the lever actuator is more stable to the external vibration.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.316.2-316
• /
• 2002

There are a lot of roots of errors in the motion of the optical pickup actuator being one of the most significant components in the CD-ROM drive. Most of the studies recently performed have a tendency to seek fur the causes from an actuator itself. We found the fact that the range of the natural frequencies of a feeding deck and an actuator is close each other through an experiment. This paper present the dynamic characteristics of an actuator affected by the motion of a feeding deck. (omitted)

• 소음진동
• /
• 제6권4호
• /
• pp.521-528
• /
• 1996

Recently, higher speed optical disk drives including computer CD-ROM drives tend to be increasingly demanded to read or write the enormous volume of digital data. To this end, both structure and controller designs of the optical pick-ups should be improved concurrently. In this paper, the pick-up during auto-focusing motion is mathematically modelled retaining all its peculiar features. The model turns out a linear time invariant system suitable for a control design namedH${\infty}$ which ensures robust stability in the presence of system uncertainties. Numerical simulations are performed to demonstrate the robustness with appropriate performance specifications being satisfied. In addition, as the implementation issue of it, procedures of temporal discretization as well as model reduction of the controller are also addressed.

• 소음진동
• /
• 제8권4호
• /
• pp.643-653
• /
• 1998

The sub-resonance modes can be easily excited by the assembling tolerance in the asymmetric type optical pick-up actuators, compared with the symmetric type. In this paper, we propose the novel method for reducing the vibration due to the sub-resonance modes whose amplitude can be decreased by adding the damper and increasing the flexibility of holder PCB. Using the finite element method, the change of mode shapes is investigated as the shape of holder PCB is modified. Experimental results support that the propopsed method reduces remarkably the vibration of sub-resonance modes of the optical pick-up actuator.

• 한국소음진동공학회논문집
• /
• 제15권2호
• /
• pp.232-238
• /
• 2005

This paper proposed an optimal plate spring design for the optical pickup suspension. This method requires an analytic solution of plate spring suspension and it can be obtained by Castigliano's theorem and moment equilibrium. However, it is very complex due to the many design variables coupled and some constraints such as pitching angle in focusing motion caused by the characteristics of plate spring. Because of the complex formulation of the analytical solution that is used as the design objective, the genetic algorithm is used to find the optimal design value satisfying design constraints.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.684-687
• /
• 2002

In optical disk drive(ODD), pickup actuator, which comprises a key part of an optical disk drive equipment. must be thin. compact, and high sensitive. Low tilt is also an important requirement for the actuator, since optical disks are to high density. This tilt occurs from around the axis parallel to the tangential and radial direction of the disk. The main reason of the moment is the coupling effect between focus driving system and tracking driving system. This paper analyzed tut quantity due to focusing and tracking force through coupled fields analysts with electromagnetic analysis and structural analysis.