• Journal of the Korean Geotechnical Society
• /
• v.20 no.4
• /
• pp.57-63
• /
• 2004

The range of stresses experienced in subgrade soils and subbase materials in pavement under working stress conditions is below about 150㎪. Therefore, the deformational characteristics of soils at low confining pressures are important properties in the analysis and design of pavement system. Subgrade soils and subbase materials were collected from the actual pavement projects for testing. To evaluate the effect of confining pressure on modulus of those materials at low confining pressures, RC and FFRC tests were performed. Interestingly, the relationship between modulus of soils and confining pressure is more appropriate in linear space than in logarithm space at low confining pressure. Based on those results, new model fur evaluating the effects of confining pressure on modulus at low confining pressures was proposed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.10a
• /
• pp.439-444
• /
• 1998

• Journal of the Korean Geotechnical Society
• /
• v.17 no.1
• /
• pp.57-65
• /
• 2001

역사적 지진 발생 기록이 풍부하고 양산 단층 영향권 내에 있어 지진 발생 가능성이 높은 경주 지역을 대상으로 지진민감도 분석을 수행하였다. 지형적 특성을 고려한 지반조사와 현장 및 실내 시험을 통하여 대상 지역 지반의 지층 구성과 각 지층의 동적 특성을 분석 평가하고, 이를 토대로 한 지반 응답 해석을 수행하였다. 9개의 시험공을 시추하여 2개소의 크로스홀 시험과 7개소의 다운홀 시험을 실시하였고, 시추부지 포함 13개소에서 SASW 시험도 수행하였다. X선 회절 및 풍화도 분석과 공진주 시험 등의 실내시험도 병행하였다. 이러한 시험 결과를 바탕으로 El Centro 지진에 의한 지표면 최대 가속도를 등가 선형 부지응답해석을 통해 평가한 결과 붕괴방지 수준에서 0.158g~0.286g, 기능수행 수준에서 0.067g~0.116g의 분포를 보였고 퇴적층에 의하여 형성된 경주 시가지 분지 지형에서 증폭정도가 심하다는 것을 알 수 있었다. 해석 결과로 볼 때, 현행 건교부 기준 설계응답스펙트럼은 경우에 따라 지반 운동을 과소평가하고 지반 고유의 공진 현상을 고려하지 못하였다. 이러한 문제를 해결하기 위하여 개선된 지반 분류방법을 소개하였고 부지고유의 지반응답평가의 중요성에 대해 제시하였다.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.2
• /
• pp.21-28
• /
• 2011

Several theoretical soil nonlinear models to predict damping ratio, which is one of the typical dynamic properties of soils, it is impractical to predict damping ratio. The resonant column and torsional shear test(RC-TS) is used to represent the dynamic behavior of soils from intermediate to medium shear strains. A limitation of RC-TS is measure precise shear strain in large strains and the modified equivalent radius($R_{eq}$) was obtained using both modified hyperbolic model and Ramberg-Osgood model. Bonneville clays were tested using RC-TS test to obtain rotation and torque. The measured rotation and torque were then compared with calculated rotation and torque using curve-fitting method. Then, the nonlinear soil model parameters were obtained and the equivalent radius was calculated using the model parameters.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.16 no.4
• /
• pp.27-36
• /
• 2012

The simulation of the field dynamic soil properties for soil modeling in the centrifuge test is important. In this study, the process of soil modeling based on the shear wave velocity profile is developed. From the resonant column test in each confining pressure, the shear wave velocity profile is expected and the modeling condition is determined by comparing it with that in the field. During the dynamic centrifuge test, the bender element test is performed for measuring the in-flight shear wave velocity profile, and the applicability of the proposed method was verified. This modeling method is applied to the centrifuge test of the Hualien Large-Scale Seismic test.

• Journal of the Korean Society for Railway
• /
• v.16 no.5
• /
• pp.386-393
• /
• 2013

In this study, the so-called repeated plate load bearing test (RPBT) used to get $E_{v2}$ values in order to check the degree of compaction of subgrade, and to get design parameters for determining the thickness of the trackbed foundation, is investigated. The test procedure of the RPBT method is scrutinized in detail. $E_{v2}$ values obtained from the field were verified in order to check the reliability of the test data. The $E_{v2}$ values obtained from high-speed rail construction sites were compared to converted modulus values obtained from resonant column (RC) test results. For these tests, medium-size samples composed of the same soils from the field were used after analyzing stress and strain levels existing in the soil below the repeated loading plates. Finite element analyses, using the PLAXIS and ABAQUS programs, were performed in order to investigate the impact of the strain influence coefficient. This was done by getting newly computed $I_z$ to get the precise strain level predicted on the subgrade surface in the full track structure; under wheel loading. It was verified that it is necessary to use precise loading steps to construct nonlinear load-settlement curves from RPBT in order to get correct $E_{v2}$ values at the proper strain levels.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.288-291
• /
• 2011

최근 아스팔트 혼합물의 배합설계법은 기존에 주로 사용하던 빔 및 마샬 배합설계법에서 수퍼페이브 배합설계법으로 점차적으로 바뀌고 있는 추세이다. 수퍼페이브의 배합설계과정에서 중요한 사항 중의 하나는 선회다짐기를 사용하는 다짐방법이다. 아스팔트 포장은 노상 위에 보조기층, 기층, 표층의 순으로 구성되는데 노상은 포장 아래 약 1.0 m의 흙부분으로 포장과 일체로 구성되며 포장체에 작용하는 하중을 최종적으로 지지하는 층이다. 따라서, 수퍼페이브 배합설계법에서 사용하는 선회다짐기를 포장과 일체로 구성되는 노상의 다짐시험에도 적용한다면 각각의 포장층에 같은 원리의 다짐방법을 적용한다는 큰 의미가 있을 것으로 판단된다. 본 논문에서는 일반 노상토에 시멘트와 플라이애시를 첨가한 강화노상토를 선회다짐기를 이용하여 시편을 제작하였고, 각 시편에 대한 탄성계수를 1축압축시험, 공진주시험, LFWD를 이용해 각각 측정하여 각 결과물들의 상관관계를 추정하고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.9
• /
• pp.57-66
• /
• 2009

In the preliminary investigation (Park et al., 2009), the use of compressional wave velocity and its measurement techniques were proposed as a new quality control measure for trackbed fills. The methodology follows exactly the same procedure as the density control, except the density being replaced by the compressional wave velocity involving consistently with resilient modulus of design stage. The specifications for the control also include field compaction water content of optimum moisture content ${\pm}2%$ as well as the compressional wave velocity. In this sequel paper, crosshole and resonant column tests were performed as well direct-arrival method and laboratory compressional wave measurements to verify the practical applicability of a methodology far the new quality control procedure based upon compressional wave velocity. The stress-modified crosshole results reasonably well agree with the direct-arrival values, and the resonant column test results also agree well with the field crosshole results. The compressional wave velocity turned out to be an excellent control measure for trackbed fills both in the theoretical and practical point of view.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.65-73
• /
• 2000

An elasto-plastic constitutive model was proposed, in which the behavior at small-to-large strain level can be modeled. The proposed model is based on the anisotropic hardening description with the generalization of isotropic hardening rule and the total stress concept. From a mathematical approach it was proved that the model includes the previous successful models. The model was verified by a series of resonant column tests, torsional shear tests and triaxial tests, and the proposed model predicted small-to-large strain behavior more consistently and accurately than the hyperbolic model and the Ramberg-Osgood model for a weathered granitic soil. In addition, the nonlinearity under small strain condition was predicted appropriately for the torsional shear test results.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.55-63
• /
• 2007

Deformational characteristics of subgrade soils are important properties in the mechanistic analysis and design of pavement system. In this study, to evaluate the effect of specimen construction methods on deformational characteristics of subgrade soils in Korea, resonant column tests were performed for specimens constructed by various methods. Specimen construction method affected to the modulus value but the variation in the normalized modulus reduction curve was almost identical. The effects of specimen construction method on modulus are decreased with increasing confining pressure. The average maximum variation in the modulus value with different specimen construction methods was estimated as 16.8%. The differences in the modulus value of the specimens with same water content and dry density conditions that made by gyratory compaction and impact compaction were very small within 5.2%. The impact compaction method was proposed as a specimen construction method for determining the design input parameter testing considering that impact compaction method is much simpler and require less expensive specimen construction equipment and setup than gyratory compaction method.