• Journal of the Korea Organic Resources Recycling Association
• /
• v.1 no.1
• /
• pp.103-113
• /
• 1993

Every year, over $3.37{\times}10^7$ ton of municipal solid waste is generated in Korea, of which about 28% is organic food waste from restaurant, dining halls and households etc. Methane conversion of the food waste by anaerobic digestion could be a viable approach for energy recovery as well as safe disposal of the waste. However, as food waste is composed of highmolecular complex polymers such as cellulose, lignin and protein, anaerobic digestion of food waste has not been efficient in terms of volumetric loading rate, solid retention time and extent of anaerobic degradation. In this research, the improved anaerobic degradation of food waste was attemped by applying rumen microorganisms to anaerobic digestion. Acidification efficiency of food waste by rumen microorganisms was compared with that of conventional acidogenesis. And optimum acidification conditions by rumen microorganisms were also determined. For the experiments, anaerobic batch reactors of 600 mL was fed with the processed (dried and milled) food waste obtained from a restaurant. Ultimate volatile fatty acid (VFA) yield produced by rumen microorganisms was about 8.4 meq VFA/g volatile solid (VS) that is 95% of the theoretical value. This yield was not much different from that of conventional acidogenesis, but hydrolysis rate was about twice faster. Cumulative VFA concentration increased from 66 meq/L to 480 meq/L, when the initial TS was increased from 1% to 15%. But VFA yield at 15% TS was half of that at 1% TS. This inhibition on the acidification might be caused by the rapid drop of pH and higher concentration of nonionized VFA. Optimal pH and temperature range for the acidification were about 6.0~7.5 and $35{\sim}45^{\circ}C$, respectively.

• Culinary science and hospitality research
• /
• v.22 no.2
• /
• pp.115-124
• /
• 2016

The purpose of this paper is to verify improvement of the basic quality of food resources and make the pork legs as the more advanced food products after taking special processing steps with the mixture of traditional medical herbs and hot water extracted coffee meal. The pH level of the pettitoes(Jokbal) showed the highest rate among the control group but it showed no statistical differences in the moisture content between the control and the pettitoes(Jokbal) processed with coffee waste extract as an additional component. In addition, the levels of crude fat and crude ash showed slight increases as the addition of the amount increase. In case of the proteins, however, tendency of slight was decreased but it was not significantly difference as the amount increases. The sodium rate in the pettitoes(Jokbal) was higher in the additional group than in the control group. Texture analysis showed a tendency of wide decrease in the hardness and chewiness depending on amount of the added coffee waste extract. On the other hand, as for the cohesiveness and springiness, there was no significant difference with the control group. In case of the lightness value, as the amount of added coffee waste extract is increased from 10% to 20% and 30%, the 'L' value was reduced significantly compared to that of the control. And the 'a' value was not significantly different compared to the coffee waste extract foil impregnated furniture control. But the 'b' values were significantly increased in accordance with the result of increasing the amount of control is at the lowest level. The result may come from the influence of coffee waste extract, which affects the color of the pettitoes(Jokbal). According to the sensory evaluation, the pork part with 10% of coffee waste extract showed the highest score in looking, chewiness, smell and preference, resulting in the improvement in quality of the pettitoes(Jokbal).

• Korean Journal of Environmental Agriculture
• /
• v.19 no.1
• /
• pp.13-19
• /
• 2000

Seasonal variations of dominant algae species and the effects of these algae on coagulation and filteration of water treatment were investigated at Chilseo water treatment plant in downstream of Nakdong river from January in 1995 to Desember of 1998. The water quality of Nakdong river was found to be a hyper eutrophic state during the investigation periods. In the measurement, Chlorophyll-a contents ranged $20.7{\sim}180.9{\mu}g/l$ and total nitrogen contents(T-N) and total phosphorus contents(T-P) exceeded more than 3.4mg/l and 0.1mg/l, respectively. The changes in dominant algae species was in the order of Stepanodiscus sp., Asterionella sp., Melosira sp., Microcystis sp. and Synedra sp. from spring to winter. Microcystis sp. especially, was blooming during summer and Synedra sp. and Stepanodiscus sp. during winter. Although most diatomous algae appeared in the water treatment process caused filter clogging and reduced efficiency of coagulation and sedimentation, Synedra sp. and Stepanodiscus sp were revealed as the main trouble algae. Malfunction of water treatment process caused by Synedra sp. and Stepanodiscus sp. started at the algae concentrations of 800cells/ml and 1,820cells/ml, respectively. When chlorophyll-a content was $18.9{\mu}g/l$, the optimum amounts of coagulant were found to be 40mg/l of Alum and 16mg/l of PACS. Under condition of chlorophyll-a content of $154.1{\mu}g/l$, addition of Alum at the level of 75mg/l and PACS at the level of 35mg/l showed the lowest turibidity. The result indicates that increased amounts of the coagulants should be added for a better water treatment as chlorophyll-a contents increased. Addition of Alum at the amount of 60mg/l and 30mg/l of PACS removed Stepanodiscus sp. algae at the rate of 85% and 83%, respectively. In case of Synedra sp., 50mg/l of Alum and 25mg/l of PACS showed removal rates of 79% and 81%, respectively. Synedra sp. algae at the standing crops of 1,500cells/ml started filter clogging and a filtering process was completely inhibited after 8 hours. At this situation the filter clogging by Synedra sp. algae occurred at the depth of 5cm from the top anthracite layer. On the other, other algae did filter clogging at the depth of 10cm.

• Management & Information Systems Review
• /
• v.35 no.1
• /
• pp.51-68
• /
• 2016

In this paper, we aim to analyze the effect of accounting policy change subsequent to the adoption of K-IFRS in Korea, whereby the firms are required to recognize impairment losses on goodwill on a periodic basis rather than to amortize over a specific period. As a principle-based accounting standard, the K-IFRS expands the scope of fair value measurement with a view to enhance the relevance and timeliness of accounting information. In the same vein, intangibles with indefinite useful life, of which goodwill is an example, are subject to regulatory impairment tests at least once a year. Related literature on the impact of mandatory change in goodwill policy document that impairment recognition is more likely to be practiced opportunistically, mainly because managers have a greater discretion to conduct the tests under K-IFRS. However, existing literature examined the frequency and/or magnitude of the goodwill impairment before versus after the K-IFRS adoption, failing to notice the impairment symptoms at individual firm level. Borrowing the definition of impairment symptoms suggested by Ramanna and Watts(2012), this study performs a series of tests to determine whether the goodwill impairment recognition achieves the goal of communicating timelier information under the K-IFRS regime. Using 947 firm-year observations from domestic companies listed in KRX and KOSDAQ markets from 2008 to 2011, we document overall delays in recognizing impairment losses on goodwill after the adoption of K-IFRS relative to prior period, based on logistic and OLS regression analyses. The results are qualitatively similar in robustness tests, which use alternative proxy for goodwill impairment symptom. Afore-mentioned results indicate that managers are likely to take advantage of the increased discretion to recognize the impairment losses on goodwill rather than to provide timelier information on impairment, inconsistent with the goal of regulatory authority, which is in line with the improvement of timeliness and relevance of accounting information in conjunction with the full implementation of K-IFRS. This study contributes to the extant literature on goodwill impairment from a methodological viewpoint. We believe that the method employed in this paper potentially diminishes the bias inherent in researches relying on ex post impairment recognition, by conducting tests based on ex ante impairment symptoms, which allows direct examination of the timeliness changes between before and after K-IFRS adoption.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.18 no.4
• /
• pp.186-194
• /
• 2013

We investigated the concentrations and distribution patterns of 17 polychlorinated dibenzo-p-dioxins/dibenzofurans(PCDD/Fs), 12 dioxin-like polychlorinated biphenyls(DL-PCBs) and 24 polybrominated diphenyl ethers(PBDEs) in sediments from Ulsan Bay in Korea. The concentrations of PCDD/Fs, DL-PCBs, and PBDEs in 33 sediment samples ranged from 0.11 to 4.86($1.81{\pm}1.04$) pg $WHO_{2005}$-TEQ $g^{-1}$ dry weight(dw), 0.06 to 44.2($4.02{\pm}7.99$) pg $WHO_{2005}$-TEQ $g^{-1}$ dw, and 2.81 to 63.8($19.4{\pm}13.9$) ng $g^{-1}$ dw, respectively. DL-PCBs had dominant contributions(mean, 88%) of total TEQ concentrations in sediment. The concentrations of target compounds in inner locations were higher than those in outer locations in Ulsan Bay (p<0.05). The dominant contribution of highly chlorinated DD/Fs in sediment was associated with combustion process from industrial complexes. Distribution pattern of DL-PCBs was similar with those of commercial PCB products. BDE209 was a dominant congener in sediment, suggesting high use amount of commercial deca-BDE product in surrounding areas.

• Korean journal of food and cookery science
• /
• v.23 no.5
• /
• pp.589-600
• /
• 2007

Recently, with the rapid expansion of the franchise restaurants, ensuring food safety has become essential for restaurant growth. Consequently, the need for food safety training and related material is in increasing demand. In this study, we identified potentially hazardous risk factors for ensuring food safety in restaurants through a food safety monitoring tool, and developed training materials for restaurant employees based on the results. The surveyed restaurants, consisting of 6 Korean restaurants and 1 Japanese restaurant were located in Seoul. Their average check was 15,500 won, ranging from 9,000 to 23,000 won. The range of their total space was 297.5 to $1322.4m^2$, and the amount of kitchen space per total area ranged from 4.4 to 30 percent. The mean score for food safety management performance was 57 out of 100 points, with a range of 51 to 73 points. For risk factor analysis, the most frequently cited sanitary violations involved the handwashing methods/handwashing facilities supplies (7.5%), receiving activities (7.5%), checking and recording of frozen/refrigerated foods temperature (0%), holding foods off the floor (0%), washing of fruits and vegetables (42%), planning and supervising facility cleaning and maintaining programs of facilities (50%), pest control (13%), and toilet equipped/cleaned (13%). Base on these results, the main points that were addressed in the hygiene training of restaurant employees included 4 principles and 8 concepts. The four principles consisted of personal hygiene, prevention of food contamination, time/temperature control, and refrigerator storage. The eight concepts included: (1) personal hygiene and cleanliness with proper handwashing, (2) approved food source and receiving management (3) refrigerator and freezer control, (4) storage management, (5) labeling, (6) prevention of food contamination, (7) cooking and reheating control, and (8) cleaning, sanitation, and plumbing control. Finally, a hygiene training manual and poster leaflets were developed as a food safety training materials for restaurants employees.

• Geophysics and Geophysical Exploration
• /
• v.13 no.1
• /
• pp.80-87
• /
• 2010

This study was conducted to develop a reservoir modelling workflow to reproduce the heterogeneous distribution of effective permeability that impacts on the performance of SAGD (Steam Assisted Gravity Drainage), the in-situ bitumen recovery technique in the Athabasca Oil Sands. Lithologic facies distribution is the main cause of the heterogeneity in bitumen reservoirs in the study area. The target formation consists of sand with mudstone facies in a fluvial-to-estuary channel system, where the mudstone interrupts fluid flow and reduces effective permeability. In this study, the lithologic facies is classified into three classes having different characteristics of effective permeability, depending on the shapes of mudstones. The reservoir modelling workflow of this study consists of two main modules; facies modelling and permeability modelling. The facies modelling provides an identification of the three lithologic facies, using a stochastic approach, which mainly control the effective permeability. The permeability modelling populates mudstone volume fraction first, then transforms it into effective permeability. A series of flow simulations applied to mini-models of the lithologic facies obtains the transformation functions of the mudstone volume fraction into the effective permeability. Seismic data contribute to the facies modelling via providing prior probability of facies, which is incorporated in the facies models by geostatistical techniques. In particular, this study employs a probabilistic neural network utilising multiple seismic attributes in facies prediction that improves the prior probability of facies. The result of using the improved prior probability in facies modelling is compared to the conventional method using a single seismic attribute to demonstrate the improvement in the facies discrimination. Using P-wave velocity in combination with density in the multiple seismic attributes is the essence of the improved facies discrimination. This paper also discusses sand matrix porosity that makes P-wave velocity differ between the different facies in the study area, where the sand matrix porosity is uniquely evaluated using log-derived porosity, P-wave velocity and photographically-predicted mudstone volume.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.672-677
• /
• 2012

Lipids in microalgal biomass were recovered by using pyrolysis method. The pyrolysis experiments of two Chlorella sp. KR-1 samples, which have triglyceride contents of 10.8% and 36.5%, respectively were carried out at $600^{\circ}C$ to investigate the effects of lipid contents in the cells on the reaction characteristics. The conversion and liquid yield of the lipid-rich sample were higher than those of the lipid-lean sample since its carbon to hydrogen ratio was low. There were low molecular weight organic acids, ketones, aldehydes and alcohols in the liquid products from both KR-1 samples, but the pyrolysis oil of the lipid-rich sample was abundant in free fatty acids, particularly palmitic acid, oleic acid and stearic acid while the content of nitrogen containing organic compounds was low. The microalgal pyrolysis oil had two layers composed of the light hydrophobic fraction and the heavy hydrophilic fraction. The light fraction might be originated from triglycerides and the heavy fraction might be from carbohydrates and proteins. In the light fraction of the liquid products, there were considerable linear alkanes such as pentadecane and heptadecane as well as free fatty acids, implying that deoxygenation reaction including decarboxylation was occurred during the pyrolysis. The yield of the liquid products from the pyrolysis of the KR-1 sample having triglyceride content of 36.5% was 56.9% and the light fraction in the liquid products was 68.2%. Also more than 80% of the light fraction was free fatty acids and pure hydrocarbons, thus showing that most triglycerides could be extracted in the form of suitable raw materials for biofuels.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.27-36
• /
• 2007

A recent study showed that MTBE can be degraded by Fenton's Reagent (FR). The treatment of MTBE with FR, however, has a definite limitation of extremely low pH requirement (optimum pH $3{\sim}4$) that makes the process impracticable under neutral pH condition on which the ferrous ion precipitate forming salt with hydroxyl anion, which result in the diminishment of the Fenton reaction and incompatible with biological treatment. Consequently, this process using only FR is not suitable for in-situ remediation of MTBE. In order to overcome this limitation, modified Fenton process using NTA, oxalate, and acetate as chelating reagents was introduced into this study. Modified Fenton reaction, available at near neutral pH, has been researched for the purpose of obtaining high performance of oxidation efficiency with stabilized ferrous or ferric ion by chelating agent. In the MTBE degradation experiment with modified Fenton reaction, it was observed that this reaction was influenced by some factors such as concentrations of ferric ion, hydrogen peroxide, and each chelating agent and pH. Six potential chelators including oxalate, succinate, acetate, citrate, NTA, and EDTA were tested to identify an appropriate chelator. Among them, oxalate, acetate, and NTA were selected based on their remediation efficiency and biodegradability of each chelator. Using NTA, the best result was obtained, showing more than 99.9% of MTBE degradation after 30 min at pH 7; the initial concentration of hydrogen peroxide, NTA, and ferric ion were 1470 mM, 6 mM, and 2 mM, respectively. Under the same experimental condition, the removal of MTBE using oxalate and acetate were 91.3% and 75.8%, respectively. Optimum concentration of iron ion were 3 mM using oxalate which showed the greatest removal efficiency. In case of acetate, $[MTBE]_0$ decreased gradually when concentration of iron ion increased above 5 mM. In this research, it was showed that modified Fenton reaction is proper for in-situ remediation of MTBE with great efficiency and the application of chelatimg agents, such as NTA, was able to make the ferric ion stable even at near neutral pH. In consequence, the outcomes of this study clearly showed that the modified Fenton process successfully coped with the limitation of the low pH requirement. Furthermore, the introduction of low molecular weight organic acids makes the process more available since these compounds have distinguishable biodegradability and it may be able to use natural iron mineral as catalyst for in situ remediation, so as to produce hydroxyl radical without the additional injection of ferric ion.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.37 no.2
• /
• pp.114-123
• /
• 2009

To investigate the possible use of plants for landscaping in reclaimed soil, a planting pilot system experiment was performed over the course of four years in reclaimed dredging area with four species: Alnus firma, Alnus hirsuta, Pinus thunbergii, and Pyrachantha angustifolia for 4 years. The physicochemical characteristics of the tested soil showed that it was sandy through coming from a reclaimed dredging area. The average pH of the tested soil was 7.16(slight alkali), and electric conductivity(EC) was relatively low, $294{\mu}S/cm$, even though it came from a saltwater area. To test the effect of planting density vs. phytomass by plant specie from a planting basin, the experiment was designed using four plant species with high and low planting densities over 4 years. The planting conditions of the growth of landscape tree species exhibited growth height as follows: A. hirsuta, A. firma, P. thunbergii, and P. angustifolia, whill the DBH followed the order of A. hirsuta, A. firma, and P. thunbergii. The total phytomass of each plant was higher at low density planting areas than high density planting area in terms of total phytomass production and growth distribution in the reclaimed dredging area. Total phytomass per unit area increased as follows: A. hirsuta, A. firma, P. thunbergii, and P. angustifolia. The total phytomass per each tested plant was 2 times higher in low density planting areas than high density planting areas. Total phytomass per unit area, however, was similar or slighty higher in high density planting areas compared to low density areas. Among the tested plants, A. hirsuta showed the highest phytomass, implying that A. hirsuta adapted very well to the reclaimed area and has the capability of a fast growth, nitrogen fixation tree, and utilizing insoluble nutrients through inoculated root nodule bacteria. The yield of phytomass per individual in low density Alnus species was greater than that of the high density. However, those per unit areas had no difference in the density-dependent planting. The ratio of belowground to aboveground was $0.21{\sim}0.26$. Thus, it could be concluded that the Alnus species are potential candidates for ornamental tree species in reclaimed dredging areas. This study offers baseline data for the use of ornamental tree species in reclaimed dredging areas. Additional research is required for different ornamental species in order to increase phytomass of a planting conditions based on reclaimed dredging areas.