• Korean Chemical Engineering Research
• /
• v.51 no.2
• /
• pp.267-271
• /
• 2013

Test bed studies with highly efficient amine $CO_2$ solvent (KoSol-4) developed by KEPCO research institute were performed. For the first time in Korea, evaluation of post-combustion $CO_2$ capture technology to capture 2 ton $CO_2$/day from a slipstream of the flue gas from a coal-fired power station was performed. Also the analysis of solvent regeneration energy was conducted to suggest the reliable performance data of the KoSol-4 solvent. For this purpose, we have tested 5 campaigns changing the operating conditions of the solvent flow rate and the stripper pressure. The overall results of these campaigns showed that the $CO_2$ removal rate met the technical guideline ($CO_2$ removal rate: 90%) suggested by IEA-GHG and that the regeneration energy of the KoSol-4 showed about 3.0~3.2 GJ/$tCO_2$ which was, compared to that of the commercial solvent MEA (Monoethanolamine), about 25% reduction of regeneration energy. Based on these results, we could confirm the good performance of the KoSol-4 solvent and the $CO_2$ capture process developed by KEPCO research institute. And also it was expected that the cost of $CO_2$ avoided could be reduced drastically if the KoSol-4 is applied to the commercial scale $CO_2$ capture plant.

• Korean Journal of Plant Resources
• /
• v.30 no.2
• /
• pp.152-159
• /
• 2017

The purpose of this study was to obtain basic data for using Aronia as a functional food material. The composition of anthocyanin was characterized and quantitated by LC-MS/MS, HPLC, and UV-VIS spectrophotometer techniques, respectively. The anthocyanin content was analyzed by temperature, time, pH, and the addition of citric acid. The UV-VIS spectrophotometer used for analysis of anthocyanin is less accurate than the LC-MS/MS method used in recent years. In the past, cyanidin-3-Glucoside was reported to be a major anthocyanin that contains Aronia. However, LC-MS/MS analysis in this study confirmed cyanidin-3-galactoside to be the major compound. The anthocyanin content of the Aronia powder began to decrease sharply at a temperature of $65^{\circ}C$ or higher when heated for 24 hours. In an aqueous solution of Aronia, the anthocyanin content was reduced by 50% at $65^{\circ}C$ for 10 hours and decreased by 85% at $85^{\circ}C$ within 10 hours. Above pH 8, the anthocyanin content was reduced by more than 50%. The results of this study will provide useful information to maintain anthocyanin content in the manufacturing process of Aronia. It could also be used to ensure the stability of anthocyanins in similar species of berries.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.402-408
• /
• 2005

This investigation aimed at selecting the optimum catalyst and reaction conditions used in Fenton oxidation for landfill leachate treatment and was carried out at ambient temperature using a lab-scale experiment. The investigation led to the following results: 1) The optimum pH and dose for each iron catalyst were as follows: $Fe^{2+}\;=\;1,200\;mg/L$, $H_2O_2\;=\;1,200\;mg/L$, initial pH=3.0; $Fe^{3+}\;=\;1,200\;mg/L$, $H_2O_2\;=\;1,500\;mg/L$, initial pH=4.5; $Fe^0\;=\;1,200\;mg/L$, $H_2O_2\;=\;900\;mg/L$, initial pH=4.0, respectively. 2) The progress of Fenton oxidation could be instrumentally monitored by measuring redox potential evolution during leachate oxidation, thus, indicating the possibility of an on-line process monitoring. 3) A simple acid-base titration of Fenton-treated leachate proved that a relevant fraction of by- products formed during the treatment was made of acidic compounds in the optimum reaction condition for each catalyst used, thus demonstrating that the higher the extent of Fenton oxidation the greater was the amount of acids formed. 4) With the aim of selecting the optimum catalyst among $Fe^0$, $Fe^{2+}$ and $Fe^{3+}$, removal efficiency of each parameter in the optimum reaction conditions was considered. Although $Fe^{3+}$ was higher than other catalysts($Fe^0$, $Fe^{2+}$) in removal efficiency, $Fe^0$ was a optimum catalyst with a view of cost effectiveness.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.36 no.4
• /
• pp.488-498
• /
• 2007

The purposes of this study were to: a) provide evidences concerning the effects of emotional leadership b) examine the impacts of emotional leadership on employee-related variables, 'job satisfaction', 'organizational commitment', 'organizational performance' and 'turnover intention', and c) identify a conceptual framework underlying emotional leadership. A survey was conducted from August 23 to November 3, 2005 to collect data from mid-level managers in food service company headquarters (N=219). Statistical analyses were completed using SPSS Win (12.0) for descriptive, reliability, factor and correlation analyses and AMOS (5.0) for confirmatory factor analysis and structural equation modeling. The main results of this study were as follows. First, the managers gave the highest point to their leaders in the emotional leadership competence 'organizational awareness : reading the currents, decision networks, and politics at the organizational level' and gave the lowest point in the emotional leadership competence 'influence: wielding effective tactics for persuasion'. Second, the means of job satisfaction was above the midpoint (3 points). Employees' job satisfaction with 'coworkers' was relatively high. However, the extents of satisfaction with 'payroll' 'promotion', and 'work environment' were relatively low. Third, the organizational commitment was above the midpoint (3 points). In the organizational commitment, 'loyalty' factor was higher than 'commitment' factor. Fourth, the means of organizational performance was above the midpoint. The highest organizational performance variable was 'internal efficiency; trying to reduce cost' and the lowest organizational performance variable was 'internal fairness ; equitable treatment and all are treated with respect with no regard to status and grade'. Fifth, most respondents intended on 'thinking of quitting ; towards turnover process'. Sixth, the test of hypothesis using structural equation modeling found that emotional leadership produced p[Isitive effects on job attitude and job performance. Emotional leadership enhanced job satisfaction and organizational commitment, and in turn, employees' attitude positive effects on organizational performance; emotional leadership also had a direct impact on organizational performance

• KDI Journal of Economic Policy
• /
• v.13 no.2
• /
• pp.97-127
• /
• 1991

This paper investigates the roles and the limitations of the Korean antitrust agencies-the Office of Fair Trade (OFT) and the Fair Trade Commission (FTC) during the making of the major industrial policies of the 1980's. The Korean antitrust agencies played only a minimal role in three major industrial policy-making issues in the 1980's- the enactment of the Industrial Development Act (IDA), the Industrial Rationalization Measures according to the IDA, and the Industrial Readjustment Measures on Consolidation of Large Insolvent Enterprises based on the revised Tax Exemption and Reduction Control Act. As causes for this performance bias in the Korean antitrust system, this paper considers five factors according to the current literature on implementation failure: ambiguous and insufficient statutory provisions of the Monopoly Regulation and Fair Trade Act (MRFTA); lack of resources; biased attitudes and motivations of the staff of the OFT and the FTC; bureaucratic incapability; and widespread misunderstanding about the roles and functions of the antitrust system in Korea. Among these five factors, bureaucratic incompetence and lack of understanding in various policy implementation environments about the roles and functions of the antitrust system have been regarded as the most important ones. Most staff members did not have enough educational training during their school years to engage in antitrust and fair trade policy-making. Furthermore, the high rate of staff turnover due to a mandatory personnel transfer system has prohibited the accumulation of knowledge and skills required for pursuing complicated structural antitrust enforcement. The limited capability of the OFT has put the agency in a disadvantaged position in negotiating with other economic ministries. The OFT has not provided plausible counter-arguments based on sound economic theories against other economic ministries' intensive market interventions in the name of rationalization and readjustment of industries. If the staff members of antitrust agencies have lacked substantive understanding of the antitrust and fair trade policy, the rest of government agencies must have had serious problems in understanding the correst roles and functions of the antitrust system. The policy environment of the Korean antitrust system, including other economic ministries, the Deputy Prime Minister, and President Chun, have tended to conceptualize the OFT more as an agency aiming only at fair trade policy and less as an agency that should enforce structural monopoly regulation as well. Based on this assessment of the performance of the Korean antitrust system, this paper evaluate current reform proposals for the MRFT A. The inclusion of the regulation of conglomerate mergers and of business divestiture orders may be a desirable revision, giving the MRFTA more complete provisions. However, given deficient staff experties and the unfavorable policy environments, it would be too optimistic and naive to expect that the inclusion of these provisions alone could improve the performance of the Korean antitrust system. In its conclusion, this paper suggests several policy recommendations for the Korean antitrust system, which would secure the stable development and accumulation of antitrust expertise for its staff members and enough understanding and conformity from its environments about its antitrust goals and functions.

• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.339-345
• /
• 2013

This study is to derive from the required performances and the optimum mix proportion of the roof concrete placed in the in-ground LNG storage tank with a capacity of 200000 $m^3$, and propose the actual data for site concrete work. The concrete placing work without sliding and segregation in the fresh concrete condition is very important because the slope of domed roof is varied in the large range by its curvature. Also the control of hydration heat and the strength development at test ages are classified with massive section about 1.4 m thick and considered to the pre-stressing work and removal of air support after concrete placing work. Considering above condition, slump range is selected $100{\pm}25$ mm under the slope $20^{\circ}$ and $150{\pm}25$ mm over the slope $20^{\circ}$ s until 60 minutes of elapsed time. Also, the roof concrete is satisfied with compressive strength range including design strength at 91 days (30 MPa), pre-stressing work at 7 days (10 MPa), air support removal work at 21 days (14 MPa). Replacement ratio of limestone powder is determined by confined water ratio test and main design factors include water-cement ratio (W/C), sand-aggregate ratio and dosage of admixture. As test results, the optimum mix proportion of the roof concrete used low heat cement is as followings. 1) Replacement ratio of limestone powder 25% by confined water ratio test 2) Water-cement ratio 57.8% 3) Sand-aggregate ratio 42.0%. Also, test results for the adiabatic temperature rising test is satisfied with its criteria and shown the lower value compared to preceding storage tank (TK-13, 14). These required performances and the optimum mix proportion is to apply the actual construction work.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.307-313
• /
• 2005

Electromigration behavior in the Sn96.5Ag3.0Cu0.5 solder lines was investigated and compared Sn96.5Ag3.0Cu0.5 with eutectic SnPb. Measurements were made for relevant parameters for electromigration of the solder, such as drift velocity, threshold current density, activation energy, as well as the product of diffusivity and effective charge number (DZ$\ast$). The threshold current density were measured to be $2.38{\times}10^4A/cm^2$ at $140^{\circ}C$ and the value represented the maximum current density which the SnAgCu solder can carry without electromigration damage at the stressing temperatures. The electromigration energy was measured to 0.56 eV in the temperature range of $110-160^{\circ}C$. The measured products of diffusivity and the effective charge number, DZ$\ast$ were $3.12{\times}10^{-10} cm^2/s$ at $110^{\circ}C$, $4.66{\times}10^{-10} cm^2/s$ at $125^{\circ}C$, $8.76{\times}10^{-10} cm^2/s$ at $140^{\circ}C$, $2.14{\times}10^{-9}cm^2/s$ at $160^{\circ}C$ SnPb solder existed incubation stage, while SnAgCu did not have incubation stage. It was thought that the diffusion mechanism of SnAgCu was different from that of SnPb.

• Journal of Life Science
• /
• v.17 no.4 s.84
• /
• pp.510-514
• /
• 2007

This study was carried on cool and RT(room temperature) storage of unhulled rice. In RT storage of an analysis of coefficient relation, high significant positive coefficients were observed in toyo index and breakdown, setback and protein content. high significant negative coefficients were showed setback and breakdown, breakdown and protein content. In cool storage of an analysis of coefficient relation, high significant positive coefficients were observed in toyo index and amylose content and gelatinization start temperature and protein content and high significant negative coefficients were showed toyo index and whiteness, toyo index and gelatinization start temperature, gelatinization start temperature and amylose content. In RT storage of a path coefficient analysis, a highest positive direct influence was observed in amylose content and a highest negative direct influence was protein content. Positive indirect influence was high revealed breakdown and protein content and negative indirect influence was gelatinization start temperature and Mg/K ratio. In cool storage of a path coefficient analysis, a highest positive direct influence was whiteness and a highest positive indirect influence was gelatinization start temperature. Positive indirect influence was high revealed gelatinization start temperature and amylose content, negative indirect influence was whiteness and gelatinization start temperature. In RT storage of Multiple regression equation of Toyo index based on physicochemical properties of unhulled rice, a highest coefficient of determination was revealed among five facters of whiteness, protein content, Mg/K ratio, amylose content and gelatinization start temperature. In cool storage of Multiple regression equation of toyo index based on physicochemical properties of unhulled rice, highest coefficient of determination was revealed among five facters of moisture content, amylose content, gelatinization start temperature, breakdown and setback.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.56-65
• /
• 2022

Copper is one of the non-ferrous metals used in the electrical/electronic manufacturing industries due to its superior properties particularly the high conductivity and less resistivity. The effluent generated from the surface finishing process of these industries contains higher copper content which gets discharged in to water bodies directly or indirectly. This causes severe environmental pollution and also results in loss of an important valuable metal. To overcome this issue, continuous R & D activities are going on across the globe in adsorption area with the purpose of finding an efficient, low cost and ecofriendly adsorbent. In view of the above, present investigation was made to compare the performance of a plant root (Datura root powder) as a bio-adsorbent to that of the synthetic one (Tulsion T-42) for copper adsorption from such effluent. Experiments were carried out in batch studies to optimize parameters such as adsorbent dose, contact time, pH, feed concentration, etc. Results of the batch experiments indicate that 0.2 g of Datura root powder and 0.1 g of Tulsion T-42 showed 95% copper adsorption from an initial feed/solution of 100 ppm Cu at pH 4 in contact time of 15 and 30 min, respectively. Adsorption data for both the adsorbents were fitted well to the Freundlich isotherm. Experimental results were also validated with the kinetic model, which showed that the adsorption of copper followed pseudo-second order rate expression for the both adsorbents. Overall result demonstrates that the bio-adsorbent tested has a potential applicability for metal recovery from the waste solutions/effluents of metal finishing units. In view of the requirements of commercial viability and minimal environmental damage there from, Datura root powder being an effective material for metal uptake, may prove to be a feasible adsorbent for copper recovery after the necessary scale-up studies.

• Clean Technology
• /
• v.28 no.2
• /
• pp.131-137
• /
• 2022

The semiconductor process currently emits various by-products and unused gases. Emissions containing pollutants are generally classified into categories such as organic, acid, alkali, thermal, and cabinet exhaust. They are discharged after treatment in an atmospheric prevention facility suitable for each exhaust type. The main components of organic exhaust are volatile organic compounds (VOC), which is a generic term for oxygen-containing hydrocarbons, sulfur-containing hydrocarbons, and volatile hydrocarbons, while the main components of alkali exhaust include ammonia and tetramethylammonium hydroxide. The purpose of this study was to determine the combustion characteristics and analyze the NO_X reduction rate by maintaining a direct combustion and temperature to process organic and alkaline exhaust gases simultaneously. Acetone, isopropyl alcohol (IPA), and propylene glycol methyl ether acetate (PGMEA) were used as VOCs and ammonia was used as an alkali exhaust material. Independent and VOC-ammonia mixture combustion tests were conducted for each material. The combustion tests for the VOCs confirmed that complete combustion occurred at an equivalence ratio of 1.4. In the ammonia combustion test, the NO_X concentration decreased at a lower equivalence ratio. In the co-combustion of VOC and ammonia, NO was dominant in the NO_X emission while NO₂ was detected at approximately 10 ppm. Overall, the concentration of nitrogen oxide decreased due to the activation of the oxidation reaction as the reaction temperature increased. On the other hand, the concentration of carbon dioxide increased. Flameless combustion with an electric heat source achieved successful combustion of VOC and ammonia. This technology is expected to have advantages in cost and compactness compared to existing organic and alkaline treatment systems applied separately.