• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.467-474
• /
• 2012

UAVs for reconnaissance and intelligence operations require long endurance capability, which demands high efficiency of the propulsion system. The distributed propulsion system(DPS) generates the thrust by replacing a large propulsion system with a number of small propulsion systems. A DPS distributed along the wing span can produce gains in propulsion efficiency by reducing ejection velocity. Also, the ingestion of boundary layers through the distributed DPS inlet and ejecting flow from the outlet can improve the lift to drag ratio of the vehicle. This study investigates the effects of locations and size of the inlet and outlet of the DPS on the blended-wing-body design based on Eppler 337 airfoil, with a CFD tool. The fans in the DPS are modeled as actuator disks for computational efficiency. The best location and aspect ratio of the inlet and outlet are found from lift-to-drag ratio and pitching moment considerations.

• Journal of Aerospace System Engineering
• /
• v.16 no.6
• /
• pp.54-63
• /
• 2022

Recently, electric propulsion aircraft with various propeller mounting positions have been under construction. The position of the propeller relative to the wing can significantly affect the aerodynamic performance of the aircraft. Placing the propeller in front of the wing produces a complex swirl flow behind or around the propeller. The up/downwash induced by the swirl flow can alter the wing's local effective angle of attack, causing a change in the aerodynamic load distribution across the wing's spanwise direction. This study investigated the influence of the distance between a propeller and a wing on the aerodynamic loads on the wing. The swirl flow generated by the propeller was modelled using an actuator disk theory, and the wing's aerodynamics were analysed with the VSPAERO tool. Results of the study were compared to wind tunnel test data and established that both axial and spanwise distance between the propeller and the wing positively affect the wing's lift-to-drag ratio. Specifically, it was observed that the lift-to-drag ratio increases when the propeller is positioned higher than the wing.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.1-9
• /
• 2017

Numerical computations are performed to investigate the effect of pintle stroke on the performance of an internal pintle thruster. Results show that the thrust control ratio was less than 2% and the aerodynamic load ratio was 22% as the pintle stroke increased. The flow past the nozzle throat rapidly expanding because of the shape of the pintle, and a shock wave was generated. Particularly, at the pintle stroke distance of 4 and 5 mm, the shock wave hit the wall of the nozzle, results in peeling bubbles. Depending on the altitude, the thrust increased and the aerodynamic load decreased, but the difference was as small as 1.5%. In the presence of the bore, the reduction of the pintle tip area resulted in a decrease in aerodynamic load.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1017-1024
• /
• 2012

The aerodynamic design and analysis on advanced propeller with blade sweep was performed for recent turboprop aircraft. HS1 airfoil series are selected as a advanced propeller blade airfoil. Adkins method is used for aerodynamic design and performance analysis with respect to the design point. Adkins method is based on the vortex-blade element theory which design the propeller to satisfy the condition for minimum energy loss. Propeller geometry is generated by varying chord length and pitch angle at design point of target aircraft. Advanced propeller is designed by apply the modified chord length, the tip sweep which is based on the geometry of conventional propeller. The aerodynamic characteristics of the designed Advanced propeller were verified by CFD(Computational Fluid Dynamic) and evaluated to be properly designed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.1
• /
• pp.53-61
• /
• 2021

This paper is a preliminary study for the development of a drone for inspection inside a boiler in a thermal power plant, which is a high-temperature environment, and validated whether the drone can fly normally through a high-temperature environment simulation using AirSim. In a high-temperature flight environment, the aerodynamic characteristics of the air density and viscosity are different from room temperature, and the flight performance of the drone is also changed accordingly. Therefore, in order to confirm the change of the aerodynamic characteristics of the propeller according to the temperature change, the propeller analysis and thrust test through JBLADE, and the operation characteristics prediction through the electric propulsion system performance prediction model were performed. In addition, the analysis and performance prediction results were applied to AirSim for simulation, and the aircraft redesigned through the analysis of the results. As a result of the redesign, it was confirmed that about 65% of the maximum power used before the redesign was reduced to 52% to obtain the necessary thrust when hovering in an environment of 80℃.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.184.1-184.1
• /
• 2010

Floating wind turbines have been suggested as a feasible solution for going further offshore into deeper waters. However, floating platforms cause additional unsteady motions induced by wind and wave conditions, so that it is difficult to predict annual energy output of wind turbines by using conventional power prediction method. That is because sectional inflow condition on a rotor plane is varied by unsteady motion of floating platforms. Therefore, aerodynamic simulation using Vortex Lattice Method(VLM) were used to investigate the influence of motion on the aerodynamic performance of a floating offshore wind turbine. Simulation with individual motion of offshore platform were compared to the case of onshore platform and carried out according to the wave height and the wave angular frequency.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.395-398
• /
• 2007

In nature, the swallowtail butterfly is known to be a versatile flyer using gliding and flapping efficiently. Furthermore, it has long tails on the hind-wing that may be associated with the enhancement of the gliding performance. In the present study, we investigate the aerodynamic property of swallowtail butterfly wing in gliding. We use an immersed boundary method and conduct a numerical simulation at the Reynolds numbers of 1,000 - 3,000 based on the free-stream velocity and the averaged chord length for seven different attack angles. As a result, we clearly identify the existence of the wing-tip and leading-edge vortices, and a pair of the streamwise vortices generated along the hind-wing tails. Interestingly, at the attack angle of $10^{\circ},$ hairpin vortices are generated above the center of the body and travel downstream.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.1 no.1
• /
• pp.166-188
• /
• 1998

본 논문에서는 쿼터니온 궤환 개념이 기존의 오일러각 궤환 개념에 비해 추력벡터제어(Thrust Vector Control) 방식을 사용하는 전술 유도탄 자세제어에 보다 효과적으로 적용될 수 있음을 보인다. 오일러각 궤환 방식을 택한 기존의 자세제어기에서 오일러각 궤환 부분을 쿼터니온 궤환으로 적절히 바꾸어 주게 되면 자세명령 크기 변화에 따른 시간응답 특성의 변화를 줄일 수 있으며, 쿼터니온 궤환 방식을 택할 경우, 우주비행체 자세제어 분야에서 활발히 연구되고 있는 고유축(Eigen Axis) 회전에 의한 자세변환을 수행할 수 있는 자세제어기 설계가 가능하다. 고유축 회전은 최단경로에 의한 자세변환 개념이므로, 이러한 능력을 갖춘 자세제어기는 신속한 자세변환이 필요한 전술 유도탄의 초기비행에 매우 효과적으로 이용될 수 있다. 더욱이, 제어법칙에 공력모멘트를 보상하는 항을 추가하게 되면 변화가 심한 공력 모멘트가 유도탄의 회전운동에 미치는 영향을 줄일 수 있어 고유축 회전성능을 보다 개선시킬 수 있다. 우선, 오일러각 궤환보다 쿼터니온 궤환이 유리한 점을 논하고, 쿼터니온 궤환에 근거한 자세제어기의 설계 개념과 제안된 제어기에 의해 구성되는 폐루우프에 대한 안정성 문제를 다룬 후, 시뮬레이션을 통해 그 타당성을 검증한다.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.169-175
• /
• 2000

A design method for transonic turbine blades is developed based on Navier-Stokes equations. The present computing process is done on the four separate steps, 1.e., determination of the blade profile, generation of the computational grids, cascade flow simulation and analysis of the computed results in the sense of the aerodynamic performance. The blade shapes are designed using the cubic polynomials under the control of the design parameters. Numerical methods for the flow equations are based on Van-Leer's FVS with an upwind TVD scheme on the finite volume. Applications are made to the VKI transonic rotor blades. Computed results are analyzed with respect to the aerodynamic performance and are compared with the experimental data.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.2
• /
• pp.59-64
• /
• 2010

A design method of Sirocco fan is developed for constructing 3-D impeller and scroll geometries, and for predicting both the aerodynamic performance and the noise characteristics of the designed fan. The aerodynamic blading design of fan is conducted by blade angle, camber line determinations and airfoil thickness distribution, and then the scroll geometry of fan is designed by using logarithmic spiral. The aerodynamic performance of designed fan is predicted by the meanline analysis with flow blockage, slip and pressure loss correlations. Based on the predicted performance data, fan noise is predicted by two models for cutoff frequency and broadband noise sources. The present predictions for the performance and the noise level of actual fans are well agreed with measurement results.