• Membrane Journal
• /
• v.26 no.3
• /
• pp.205-211
• /
• 2016

Performance of pyrophyllite-based ceramic membranes newly developed were investigated. Membrane fouling caused by microbial suspensions taken from a full-scaled MBR system at domestic wastewater treatment plant was observed at different airflow rate and distance between each membrane. For the pyrophyllite support, pore size was about $1.0{\mu}m$, but surface coating with $Al_2O_3$ solution decreased the pore size with the reduction of the pure water permeability. With the MLSS taken from the full-scaled MBR system (6 g/L), the fouling rate was decreased by increasing airflow rate under $20L/m^2{\cdot}hr$ of setpoint flux. However, the effectiveness of the airflow rate on the fouling control depends strongly upon the gap between each membrane. At fixed airflow rate, the fouling rate was decreased by increasing the gap between each pyrophyllite membrane. Nevertheless, further increasing the membrane distance from 3.5 to 5.4 cm resulted in higher fouling rate. Similar result was observed with the $Al_2O_3$ coated-pyrophyllite membrane. Nevertheless, the fouling rate was lower with the coated membrane than that observed with the uncoated pyrophyllite support. Regardless of surface coating, the suspended solids were removed almost completely and the surface coating on the pyrophyllite support improved organic rejection with PEG solution (MW : 8000 kDa) tested.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.157.1-157.1
• /
• 2005

• Membrane Journal
• /
• v.21 no.1
• /
• pp.62-71
• /
• 2011

Highly enriched oxygen is used in energy-efficient combustion due to decreased non-flammable nitrogen, while high purity nitrogen is used for explosion proof in the LNG ships and keeping the freshness of green stuffs. Membrane technology can be used in these $O_2$ and $N_2$ generation with low energy consumption. In this study, PES was used as a membrane material and 1-methyl-2-pyrollidone (NMP) and acetone were employed as a good solvent and nonsolvent addictive (swelling agent to PES), respectively. Dope solutions were prepared by changing the content of acetone (0, 6.5, 15, 25, 31.5 wt%) in 37 wt% PES solutions. Hollow fiber spinning was performed at 0~10 cm of air-gap distances for each dope solution. $O_2/N_2$ selectivity and permeability were investigated by comparing of hollow fibers coated or not by silicons. $O_2/N_2$ selectivity increased and permeance of $O_2$ and $N_2$ decreased with increasing air-gap height independently of acetone addictions. Optimized PES hollow fibers were obtained with 37/6.5/56.5 wt% PES/acetone/NMP dope solution and 10 cm air-gap, which showed 7.3 of $O_2/N_2$ selectivity and 4.3 GPU of $O_2$ permeability after silicon coating.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.4
• /
• pp.103-111
• /
• 2009

Moisture is one of the important design factors that affects to the changes of physical properties and air permeability in the composting matrix. This study examines the effects of moisture during the wetting and drying procedure on physical properties like bulk density, particle size, free air space and air permeability in the sawdust used as the bulking agent in composting process. During both procedures of wetting and drying of the water, with increasing moisture content, bulk density and particle size increased, but FAS decreased. In the range of near 40 to 60% moisture content on a wet basis, particle size and FAS in wetting procedure were larger and higher than those in drying procedure. During wetting procedure, pressure drop continuously decreased ranging from near 20 to 60% moisture content, despite of decreasing FAS as a consequence of increasing moisture, and then over the range of 60% moisture content, pressure drop rapidly increased to the saturated moisture condition while the pore space was filled with the water. On the other hand, during drying procedure, pressure drop decreased from the saturated condition to 40% moisture content. In the recommended range of 50 to 60% moisture content for composting operation, pressure drop in wetting procedure were lower than in drying procedure. For the enhancement of the air permeability in the composting matrix, the wetting procedure was proper than the drying procedure, and the optimum moisture content for the efficient composting operation was appeared to be near 60%.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.187-195
• /
• 2001

승용차 실내소음은 소음의 전달 방법에 따라 구조기인소음(structure-borne noise)과 공기기인소음(air-borne noise)으로 구별된다. 구조기인 소음은 차체에 전달된 외력이 차체를 통하여 전달되고 전달된 차체의 진통이 최종적으로 차실을 이루는 패널의 진동을 일으켜 승객에 전달되는 소음이며 공기기인소음은 발생한 소읍이 공기를 타고 전파되어 차실을 투과하여 승객의 귀에 전달되는 소음을 말한다. 구조기인소음을 일으키는 기진력으로 엔진의 관성 및 폭발력, 노면의 입력, 구동계 진동, 풍력 등이 있다. 발생된 기진력은 엔진 마운트, 서스펜션 등을 통하여 차체에 전달되고 최종적으로 대쉬, 루프 등의 패널을 떨게 만들며 이러한 진동은 50∼500Hz 대역에서 차실 공간의 음향 특성에 따라 가감되어 저주파 실내 소음을 발생시킨다. 500Hz 이상 대역의 실내소음은 일반적으로 공기기인 소음이 대부분을 차치하게 된다.(중략)

• Solar Energy
• /
• v.14 no.2
• /
• pp.29-37
• /
• 1994

Radiative charaacteristics of glass windows and porous absorbing media which can be used for a solar air heater are determined through the measurements of spectral transmittances. Those in the visible range are measured by the UV-IR spectrometer. Refractive index of glass are obtained by the comparison of the measured transmittances and the correlations derived from the electromagnetic theory and are compared to the theoretical ones calculated from the classical dispersion theory. Absorption and back-scattering coefficients of 15-mesh stainless wire screens are calcuated by the comparison of the measured transmittances and the correlations derived from the two flux model.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.362-366
• /
• 1999

Membranes for biosensor were prepared from poly(vinyl chloride) (PVC)l derivatives using the solution casting method, and their gas permeabilities were studied. The polymer membranes dried slowly in air showed higher permeability coefficients than those dried in vacuum. The permeabilily coefficients of carboxylated poly(vinyl chloride) (CPVC) membranes for $O_2$ and $CO_2$ decreased as the pressure of the feed gas increased. The addition of dioctylphthalate (DOP) enhanced the permeation rates for $O_2$ and $CO_2$. For example, the permeability coefficients of CPVC membranes containing 30 wt. % DOP for $O_2$ and $CO_2$ at 100 psig were 2.03 and 0.96 Barrer, respectively, which were about 4~5 times higher than those of the membranes without DOP. Poly(vinyl chloride-co-vinyl acetate-co-vinyl alcohol) (Syn-PVCAcAl) obtained by hydrolysis of poly(vinyl chloride-co-vinyl acetate (PVCA) showed a higher permeability coefficient for $CO_2$ in the presence of DOP than that for commercial PVCAcAl, but did not show any significant difference in permeability for $O_2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.468-474
• /
• 2020

Metal ducts for transporting air conditioning and heating inside ships have recently been replaced by cloth ducts that have the advantage of delivering air evenly to the compartments, with excellent noise reduction in major compartments, such as combat command rooms, steering rooms, and sound detector cabins. Since the performance requirements of fabric ducts for vessels are strict, and the entire length of the ducts was imported from Korea, the government wants to create economic effects through localization of fabric ducts. Air permeability and fire prevention performance tests verified the applicability to naval vessels of fabric ducts developed by Hyundai Heavy Industries and HiDact, and performance requirements presented in the POS were verified. As a result of the tests, the fabric ducts met the requirements for air permeability and fireproof performance.

• Journal of Fashion Business
• /
• v.11 no.4
• /
• pp.92-100
• /
• 2007

The most emphasized materials in the modern fashion are the elastic materials with the advent of sportswear. In the area of elastic materials, the technology of foaming plastics became main research area. As novel materials, latex and neoprene based fabrics are emerging for the elastic material, among those elastic material staged by renowned fashion designers. We searched those works through literature and pictures, and examined the physical properties. Neoprene composite with filament knit fabrics are excellent in strength and water-proof. Latex fabrics gave smooth feel and elastic feel. These may be adequate for aesthetic textile material. Based on these characteristics, these techno-texitiles will find broad applications in the fashionable materials.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.44-48
• /
• 2011

본 연구에서는 구조물 상치에 에어챔버를 설치하여 챔버 내부의 공기주입량에 따라 흘수심을 조절 할 수 있는 유공 및 투수성부유식방파제를 사용하였으며, 부유식방파제의 흘수심구간에 유공을 두어 내부의 흐름에 따른 에너지소산 효과를 수리모형실험을 통하여 분석하였다. 기존 연구에 의하여 선행되어진 부유식방파제의 형상은 구조물 제체의 입사면과 투과면이 막힌 형태의 연구가 대다수였으나, 계류라인의 장력에 따른 부체의 안정성을 고려하여 본 수리모형실험에서는 입사면 흘수심구간과 투과면 흘수심구간에 유공 및 투수층을 두어 진행하는 입사파랑을 일부 흡수하도록 하였다. 또한, 부유식방파제 흘수심단면의 내부에서 흐름변화에 의한 에너지소산 효과와 입사면과 투과면의 유공률 변화에 따른 방파성능을 무공 부유식방파제와 비교하며 효율성을 분석하였다.