• Journal of the Society of Disaster Information
• /
• v.14 no.1
• /
• pp.43-50
• /
• 2018

This study presented 3D Finite Element (FE) analysis of curved beam structures subjected to static and dynamic loading conditions, which is particularly strong ground motions. It was shown that the results obtained from 3D FE analyses was similar to the theoretical solution within 1% convergency error, in order to validate the 3D solid FE models in this study. In particular, it was focusing on development of dynamic characteristics of curved beam structures subjected to three-different seismic ground motions: GyeongJu, Lomaprieta and Northridge earthquakes. Consequently, It was interesting to find that the results obtained from GyeongJu earthquake was detuned due to high frequency effect, but the Von-Mises of the curved beam structure under Lomaprieta earthquake was 647.824 MPa at 45 curvature degree.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.215-225
• /
• 1988

The curved structures in space, such as multi-level interchanges, ramped structures, and circular curved structures can be modelled as helically curved members with constant helix angle. This paper presents a finite element approach for the analysis of the static and the free vibration characteristics of the helically curved members by using the 7th order Hermite interpolation functions. This method is used to find more accurate solution of the static and dynamic responses of them than those of the previous studies.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.116-121
• /
• 2021

A lot of research is being done to develop a high-efficiency heat pump to save energy, and research to reduce or eliminate the phenomenon of frost occurring in the outdoor unit coil is also being conducted at the same time. A curved constant temperature chamber was constructed that can be tested under the same conditions as in the natural state so that the research can be conducted in which frost does not occur on the outdoor unit of the heat pump regardless of the season. Simulations were performed to verity whether such a curved constant temperature chamber has feasibility as an experimental device. For CFD conditions, the length of the straight duct in front of the outdoor unit located in the duct-type constant temperature chamber was 1, 5, 10 and 15 times the diameter of the duct. As a result, it was found that a straight space must be secured 10 times the diameter of the duct.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.9 no.3
• /
• pp.171-182
• /
• 2006

In this study, rainfall-runoff analysis was performed for Yongdam watershed($930km^2$) using KOWACO flood analysis model based on Storage Function Method as lumped hydrologic model and Vflo which was developed for real-time flood prediction by University of Oklahoma. The results shows that, the hydrographs of lumped and distributed model with uncalibrated parameters which estimated from physical or experimental relationship show significant biases from observed hydrographs. However, the hydrograph at Cheoncheon site from the distributed model follows the actual hydrograph to an extent that no more calibration is necessary. It encourages that distributed model can have advantages for application in real-time flood forecasting as physically based distributed hydrologic model which can construct event-independent basin parameter group.

• Computational Structural Engineering
• /
• v.9 no.1
• /
• pp.133-139
• /
• 1996

In this paper, an approximate method is developed to obtain the natural frequencies of the out of plane vibration of circular curved beams. The governing differential equations are derived using the dynamic equilibrium equations with the Timoshenko theory, and solved numerically. The Runge-Kutta method and Regula-Falsi method are used to integrate the differential equations and to determine the natural frequencies, respectively. In numerical examples, the hinged-hinged and clamped-clamped end constraints are considered. For each case, the four lowest natural frequencies are reported as functions of four non-dimensional system parameters.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.949-949
• /
• 2012

유출수문곡선은 강우량, 강우강도, 강우지속시간, 강우이동방향 및 이동속도와 같은 강우발생특성과 강수대의 공간적 이류방향과 유역형상과의 상호작용에 의하여 영향을 받으며, 특히 강우의 이류과정에서 나타나는 시간적, 공간적인 분포는 유출에 영향을 미치는 중요한 인자이다. 일반적으로 유출해석 기본이론은 연속방정식과 운동방정식으로서 운동파가정(kinematic wave analogy)을 기반으로 한 집중수문모형(lumped hydrologic model)에 의하여 수행되고 있지만 집중형 모형은 한 매개변수에 여러 가지의 물리적 과정을 개념화하여 담고 있기 때문에 유출과정에 대한 섬세한 모형화의 제약으로 인하여 강우의 이류과정에 따른 유출변화특성을 모의하기가 어렵다. 본 연구에서는 완전 분포형 수문동력학적 강우-유출 모형을 사용하여 강우의 이류특성을 반영할 수 있는 유출 모델을 구성하고, 강우의 이류특성에 따른 유역 출구에서의 유출수문곡선의 변화과정을 살펴보고 상관관계를 분석하였다.

• The Journal of the Korea Contents Association
• /
• v.10 no.8
• /
• pp.426-432
• /
• 2010

A level-set finite-element method is employed to investigate the free surface flow of two conceptual fish passage designs. While one design has a right-angled entrance from the reservoir to the fish passage chute, the other has a curved-shaped entrance. The numerical results are validated with hydraulic experiments through comparison of the free surface location and the pressure distribution in the spillway. It is observed that the right-angled design yields a curved free surface and pressure distribution in the vicinity of the entrance due to large strains, whereas the curved-shaped design yields a smooth flow transition with small strains. The subatmospheirc pressure distributions near the spillway ogee crest for both designs exhibit similar flow patterns. It is concluded that the curved-shaped design is more favorable for fish passage because of the feature of a smooth flow transition with small strains.

• Journal of The Korean Association For Science Education
• /
• v.35 no.1
• /
• pp.121-130
• /
• 2015

Identifying students' achievement level and reflecting it on educational policy making or instructional improvement by analyzing the results of nationwide standardized assessment is an integral part of accountability in education. On the basis of this premise, we analyzed the characteristics of National Assessment of Educational Achievement (NAEA) items for middle school science subject conducted from 2010 to 2013 by using the option response rate distribution curve, the fittest graph estimated from the response rate of correct/incorrect options by achievement score. Furthermore, we classified the type of option response rate curve in terms of correct and incorrect options. Results of the analysis of option response curve showed that five types of correct option response curve (S-shaped, J-shaped, straight-shaped, F-shaped, and step-shaped) and 4 types of incorrect option response curve (down-slope, flat, mound, and up-slope) were identified. The most common type of items was the combination of S-shaped correct option response curve and down-slope incorrect option response curve, which are considered as appropriate items to discriminate the students according to achievement level. Moreover, correct option response was found to be correlated with incorrect option response. Based on the results, we also discussed some implications on teaching-learning method and classroom assessment in science education.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.189-189
• /
• 2004

본 논문은 CNC 밀링머신을 이용한 절삭가공 등 2축시스템의 위치제어 시스템을 대상으로 한다. 기존의 제어방식은 크게 독립축제어와 상호결합제어로 분류할 수 있다. 독립축제어는 두 축의 통합된 운동을 각각의 독립된 축에 대한 추적제어를 수행하여 원하는 공구경로의 위치 정밀성을 향상시키고자 하는 것이고, 상호결합제어는 지령경로에 대한 추적성능보다는 현재의 윤곽오차를 감소시키는 방향으로 제어입력을 인가하여 가공윤곽의 오차를 감소시키는데 주목적이 있다. 또한 최근의 작업공정의 고속화 경향은 윤곽오차를 감소시키면서도 추적성능이 우수한 제어방식을 요구하고 있다.(중략)

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.30 no.1
• /
• pp.66-73
• /
• 2007

일반 투자안의 의사결정에서와 마찬가지로 산업설비의 경제성 분석에서도 가장 중요한 결정 요소 중의 하나가 설비의 생존곡선 추정이다. 설비의 자산 가치가 감소하는 원인은 여러 가지가 있으나, 여러 원인 중 물리적 훼손이 과거의 산업설비에서는 가장 중요한 원인이었으므로 기존의 생존모형 분석에서는 lows 생존곡선을 이용하여 설비의 생존곡선을 추정하였다. 그러나 새로운 기술상의 변화로 인한 첨단 생산시스템의 설비교체 분석 시에는 적합지 않다. 따라서, 본 연구에서 제안된 혼합형 Weibull 함수를 이용하여 설비의 폐기 형태를 추정함으로써 설비들의 실제적인 생존곡선을 정확하게 파악할 수 있다.