• Journal of the Korea Concrete Institute
• /
• v.15 no.6
• /
• pp.877-887
• /
• 2003

For a performance-based design of structural walls, it is necessary to develop a rational design method for determining the length and detail of boundary confinement so as to satisfy the given ductility demand. In the present study, the curvature capacity of a structural wall with boundary confinement was estimated considering the effects of various design parameters. The curvature demand of the plastic hinge corresponding to the given design displacement was also determined. By equalizing the curvature capacity to the demand, a design method for determining the length of boundary confinement, was developed. According to the design method, the length of boundary confinement increases as axial compressive load and design displacement increase, and as concrete strength, wall thickness, amount of lateral reinforcement and aspect ratio decrease. A study was performed on details for effective lateral confinement of walls with rectangular cross-section. Based on the findings, design guidelines on spacings of ties and cross-ties were proposed.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.6
• /
• pp.75-81
• /
• 2001

In this paper we analyzed the localization error of near-field detection algorithm in the sea. The near-field detection algorithms using triangulation and wavefront curvature basically assume a signal in two dimension of bearing and range. But the assumption causes localization error because there is three dimension of bearing, range, and depth in the sea. Even through three dimensional effect is considered, the localization error is occurred if multipath propagation in the sea is ignored. To analyze the localization error in the sea, we simulate the near-field localization using acoustic propagation model and focused beamforming considering wavefront curvature. The simulation results indicate that localization error always occurs in the sea and the error varied with sound velocity profile, water depth, bottom slope, source range, etc.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.1
• /
• pp.1-12
• /
• 2005

An analytical procedure to analyze reinforced concrete (RC) beams subject to monotonic loadings is proposed on the basis of the moment-curvature relations of RC sections. Unlike previous analytical models which result the overestimation of stiffnesses and underestimation of structural deformations induced from ignoring the shear deformation and assuming perfect-bond condition between steel and concrete, the proposed relation considers the rigid-body-motion due to anchorage slip at the fixed end. The advantages of the proposed relation, compared with the previous numerical models, are on the promotion in effectiveness of analysis and reflection of influencing factors which must be considered in nonlinear analysis of RC beam by taking into account the nonlinear effects into the simplifying moment-curvature relation. Finally, correlation studies between analytical and experimental results are conducted to establish the applicability of the proposed model to the nonlinear analysis of RC structures.

• The KIPS Transactions:PartB
• /
• v.9B no.6
• /
• pp.727-734
• /
• 2002

Currently. people become interested in the development of measuring instrument related to eyesight. In this study, we developed software of electronic part in automatic refracto-keratometer. If an automatic system, which uses images from an optical instrument, can inform the in-spector of an accurate eyesight measured value after the internal process, the frequency of mistakenly observed value will be reduced considerably. This software is using morphological filtering and gray-level signal enhancing techniques. The morphological filtering is the first process, from images of the optical instrument, to transform an original image which is hard to process into manageable one. The second process is a signal enhancing technique to the first processed image using gray -level thresholding technique and is used to reduce an error caused by the variety in distribution of the gray value of image. Therefore, this software system in electronic part will make more effective eyesight measurement by reducing the error effectively when applied to the optical image which is difficult to get accurate measurement value.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.761-768
• /
• 2010

When cracks occur in reinforced concrete structures, a steel carries all tensile force at crack section, while the concrete between cracks carries a part of the tensile force due to bond, so that the steel is less elongated. This is called the tension-stiffening effect, that plays an important role in verification of a serviceability limit state. But it is a complicated work to use a complex strain distribution between cracks, therefore an average strain is used to calculate deflection and crack width. In Eurocode 2, tension-stiffening effect expressed in the first order form or the second order form is used in calculating an average curvature for deflection. In this study for a flexural member deflection and crack width are calculated using various models for the tension-stiffening effect and the results are compared with the values of Eurocode 2 and KCI provisions. As results, the predicted values using the second order form are appeared to be well agreed with the experimental values and it could secure more analytical consistency.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.420-425
• /
• 2000

The room-temperature shapes of cured unsymmetric composite laminates have out-of-plane warping after autoclave processing. In addition, they exhibit two stable room-temperature configurations due to snap-through phenomena when the side length of laminates exceeds a critical value. The cured shapes of unsymmetric laminates are influenced by many environmental factors. Experiments show that the effect of too-plate cannot be ignored and has significant influence on the cured shape of unsymmetric laminates. In this present study, approximations to the strain fields are used in the expression for the total potential energy and the Rayleigh-Ritz method is applied. The slippage effects resulting from the interaction between the laminates and the tool-plate are considered. By introducing a dimensionless slippage coefficient and correlating the corresponding value with experimental results, the influence of processing parameters is investigated. Modeling is extended to predict curvatures of plate configurations with various aspect ratio.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.239-251
• /
• 1998

본 연구에서는 비대칭 박벽단면을 갖는 곡선보의 안정성해석을 수행할 수 있는 이론 및 엄밀해를 제시하기 위하여, 3차원 연속체로부터 유도된 평형방정식으로부터 선형화된 가상일의 원리를 적용하였다. 박벽단면의 구속된 ？(warping)과 곡률효과를 고려하고 유한한 회전각의 2차항을 포함하는 곡선보의 변위장을 도입하여 단면에 대해 적분함으로써 도심축에 대한 박벽 곡선보의 총포텐셜에너지를 유도하였다. 또한, 단순지지되고 일축대칭 단면을 갖는 박벽원형 곡선보의 면내 및 면외좌굴에 대한 엄밀해를 유도하기 위하여, 면내에 대해서는 균일압축을 받는 원형아치의 역대칭 좌굴모드에 대한 좌굴하중을 유도하고 면외좌굴에 대해서는 균일압축 및 순수휨을 받는 아치의 처짐함수를 가정하여 곡선보의 횡좌굴하중에 대한 일반해를 제시하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.468-468
• /
• 2012

레이더 강우를 적극적으로 활용하기 위해서는 레이더 강우에 포함된 각 오차들에 대한 특성을 파악하고 정량화하는 것이 무엇보다 중요하다. 본 연구에서는 레이더 반사도의 오차구조를 파악하고 그러한 오차구조를 갖는 반사도로부터 표출한 CAPPI의 거리오차를 보정하였다. 이러한 거리오차 파악을 위해서는 참 값으로 가정할 수 있는 기준 반사도가 필요하며 본 연구에서는 VPR 모형으로부터 기준 반사도인 지상 반사도를 추정하였다. 그 결과 일정한 VPR 모형을 적용하게 되면 거리와 상관없이 오차는 일정하고 오직 고도에 의해서만 영향을 받는다. 그러나 일정 고도에서의 반사도 표출 방법인 CAPPI는 지구곡률효과로 인해 실제로 거리가 멀어 질수록 관측 고도가 높아진다. 이에 따라서 오차는 거리가 멀어질수록 커지게 된다. 이는 실제 호우사상에 적용한 결과에서도 유사하게 나타났다. 강릉 기상 레이더의 경우 1.5km CAPPI는 약 100km까지 1.5km 고도를 유지하다 그 이상부터 고도가 점점 높아진다. CAPPI의 오차를 거리에 따라 분포시킨 결과에서도 100km까지는 어느 정도 일정한 오차를 보이다 그 이상부터 오차가 점점 증가하는 것으로 나타났다. CAPPI의 오차를 2차원 평면으로 나타낸 결과에서도 호우가 전반적으로 퍼져있는 시점부터 원거리에서 큰 오차를 보이고 있다. 이는 오차의 평균에서 더욱 명확히 나타났다. 이와 같이 CAPPI는 원거리 자료에서 오차가 크게 나타나고 있다. 이에 CAPPI에 포함된 거리오차를 VPR 모형을 이용하여 보정하였다. 그 결과 원거리에서의 오차가 감소하였음을 확인하였다.

• Proceedings of the Korean Society of Coastal and Ocean Engineers Conference
• /
• 2000.09a
• /
• pp.95-102
• /
• 2000

선형분산을 가정한 Berkhoff(1972)의 완경사방정식은 단일주기파(monochromaticwave)에 대해 심해로부터 천해까지 수심에 제한 없이 파랑의 변형을 해석할 수 있으나 식의 유도과정 중 바닥이 완경사(｜∇h｜/kh≪1) 라는 가정을 도입함으로써, 바닥곡률항(∇$^2$h)과 바닥경사의 제곱항(｜∇h｜$^2$)으로 대표되는 고차수심효과를 무시하였다. (중략)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.3
• /
• pp.751-756
• /
• 1991

본 연구에서는 Ashwell이 제시한 변형률요소를 전단효과를 고려한 두꺼운 곡 선보 요소에 적용 하였다. 막 변형률, 곡률, 전단변형률 각각에 독립된 변형률 함수 를 가정하여 미분 방정식의 일반해를 구하면 정확한 강체변위의 표현은 물론, 강성과 잉현상을 피할 수 있고 얇은 곡선보에서 두꺼운 곡선보에 이르기까지 보의 해석에 있 어서, 2절점으로 구성되는 적은 자유도수에서 높은 정확도를 보여주는 간편하고도 효 율적인 요소를 개발하고자 하였다.