• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.6
• /
• pp.91-97
• /
• 2015

The limit values of mechanical properties(MPs) of HTPB/AP/Al Solid Propellant was reviewed according to the rocket motor development procedures and the in-process values of MPs were analyzed by the tool of Process Capability Index. Based on finding the dependency among MPs, the optimization is proposed for reducing the properties defects and for improving the rocket grain safeties.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.57-62
• /
• 2013

A crack in a solid propellant increases the area of burning surface, which leads to excessive burning that causes motor failure. Therefore, it is necessary to evaluate fracture toughness of solid propellants. However, it is very difficult to measure fracture toughness of solid propellants because of the nonlinear mechanical behavior. In this study, evaluation of fracture toughness on a solid propellant was carried out under the assumption that the solid propellant is a linear viscoelastic material. Actual displacements from fracture toughness tests using CCT specimens were converted into pseudo-elastic displacements by using stress relaxation characteristics and fracture toughness was evaluated using ASTM E399 standard. Also, effects of test temperature and speed on the fracture toughness were considered.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.206-209
• /
• 2010

The visualization device for hybrid rocket is fabricated to investigate the combustion phenomena. Visualization device were composed with ignition system, oxidizer supply system, control system and data acquisition system, combustion visualization system. GOX as oxidizer and HDPE, Paraffin-LDPE Blending, Paraffin sd were used. As results, combustion phenomena and fuel droplet entrainment were observed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.3
• /
• pp.48-55
• /
• 2014

In present study, design and hot fire tests of the pryostarter are conducted. To prevent the turbopump RPM overshoot, regressive mass flow rate profile is applied. Sudden decrease of the mass flow rate at the end of the propellant burning is realized as well. Firing test results show good agreements with the design requirements. Through the study with ignition substance variations, combustion products and ignition performances are improved.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.246-250
• /
• 2006

In general, combustion characteristic of hybrid propulsion was shown with the regression rate depending on only massflow rate of oxidizer But this empirical relation was not represented well effect of the thermo-chemical properties of solid fuel. So, in this study, the combustion characteristics was studied with the mass transfer number(B number) of solid fuel instead of regression rate with various fuel. The PMMA, PP, and PE were used as fuel, and gas oxygen as oxidizer in this experiment. The mass flowrate of gas oxigen was controlled by the several chocked orifices that have different diameter, and the oxidizer supply range was $3.66\sim45.3g/sec$. As result, the empirical relation for mass flux of solid fuel was obtained with mass transfer number, and mass flux of oxidizer as follow; $\dot{m}^{'}_f\;=\;0.0175G^{0.55}B^{0.4}$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.62-68
• /
• 2009

The interaction between wall blowing and oxidizer flow can generate a very complicated flow characteristics in combustion chamber of hybrid rockets. LES analysis was conducted with an in-house CFD code to investigate the features of turbulent flow without chemical reactions. The numerical results reveal that the flow oscillations at a certain frequency exists on the fuel surface, which is analogous to those observed in the solid propellant combustion. However, the observation of oscillating flow at a certain frequency is only limited to a very thin layer adjacent to wall surface and the strength of the oscillation is not strong enough to induce the drastic change in temperature gradient on the surface. The visualization of fluctuating pressure components shows the periodic appearance of relatively high and low pressure regions along the axial direction. This subsequently results in the oscillation of flow at a certain fixed frequency. This implies that the resonance phenomenon would be possible if the external disturbances such as acoustic excitation could be imposed to the oscillating flow in the combustion chamber.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.4
• /
• pp.40-49
• /
• 2001

The basic research on AKM(Apogee Kick Motor) for space launch vehicle was carried out. AKM which will be used as 3rd stage solid rocket motor in 3-stage Korean Sounding Rocket(III) has been developing. KM is a solid rocket motor using composite propellant based on HTPB and is composed of composite motor case and submerged nozzle. To develop KM rocket motor satisfing a given set of requirement, firstly the full-scale KM with diameter 520mm was designed, then sub-scale motors reduced about 60% were manufactured and tested. Full-scale ground firing test is accomplished two times.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.114-122
• /
• 2000

Bullet impact tests for solid rocket motor were performed and its results wert described. Two motors were made of composite and steel for case material, respectively and their reactions to the bullet impact were compared. Throughout the tests it had been tried to setup the procedure of bullet impact test and criteria of the judgment for the reactions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.10-17
• /
• 2013

This paper describes a study on after-burning suppressant in a solid propellant to reduce the plume formed outside of rocket nozzles, which could expose the launch site and the flight track. The minimum smoke propellant to enhance the stealth ability was formulated in terms of the kinds and the effects of after-burning suppressant on the ballistic performance and the amount of primary smoke. A after-burning suppressant, $K_2SO_4$ of about 1.1% weight content was found to show profound reduction of the rocket plume, giving negligibly slight increase in pressure exponent of burning rate. Also minimum smoke propellant with less than 1.1% of $K_2SO_4$ corresponds to A-class satisfaction in primary smoke by AGARD standard.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.2
• /
• pp.46-53
• /
• 2010

The purpose of this paper is to study combustion characteristics with the different phase of oxidizer in hybrid rocket combustion. HDPE(High Density Polyethylene) as fuel and $GN_2O$(Gas $N_2O$), $LN_2O$(Liquid $N_2O$) as oxidizer were used to perform the experiments. An investigation was performed for a change of the regression rate, pressure of combustion chamber and combustion efficiency according to the variation of oxidizer phase. In case of using $LN_2O$ as oxidizer, the regression rate is not significantly different from using $GN_2O$ as oxidizer. It is considered that combustion energy is much larger than latent heat energy which was used in the evaporation of liquid oxidizer. However propulsion performance efficiency for $LN_2O$ showed lower value than for $GN_2O$. By increasing the flow rate of liquid oxidizer, heat transfer needed for vaporization of liquid oxidizer was increased, which resulted in the growth of combustion instability.