• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.3
• /
• pp.45-52
• /
• 2006

In this paper, we analyze on the effect of LCR filter to mitigate transient overvoltage on the high voltage induction motor fed by H-bridge cascaded 7-level inverter. The switching surge voltage that it was occurred in inverter appears transient overvoltage at the motor input terminal. the transient overvoltage becomes the major cause to occur the insulation failure by serious voltage stress in the stator winding of high voltage induction motor. The effect of transient overvoltage appears more serious in high voltage induction motor than low voltage induction motor. We selected LCR filter for reduction of the transient overvoltage. Consequently, we demonstrated that the LCR filter connected to the invertor output terminals greatly reduces the transient voltage stress and ringing. The results of simulation show the suppression of transient overvoltage at the motor end of a long cable. using EMTP

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.145-151
• /
• 2010

Voltage unbalance is regarded as a power quality problem of significant at the user application. Although the voltages are quite well balanced at the transmission system, the voltage level of utilization can be unbalanced due to the unequal system impedances and the unequal distribution of single phase loads. Capacitor is generally used for power-factor compensation and reducing harmonics of non linear load with reactor. If voltage unbalance exists, current unbalance is generated and it will be reflected in the capacity variance. When the reactor and condenser are used at the same location, generally its trouble rate is high. And it is very important checking out that how the variance of voltage, current and capacity of condenser is proceeded by the voltage unbalance. In this paper, we calculated that voltage, current and capacity of condenser are within the tolerance limit of official regulations in the event of voltage unbalance with/without reactor.

• Korean Journal of Optics and Photonics
• /
• v.11 no.1
• /
• pp.25-32
• /
• 2000

Comparisons are made between the first hyperpolarizability $\beta$ of pure N-(4-nitrophenyl)-(L)-prolinol (NPP) and poly (methyl metacrylate) (PMMA) or poly-p-(phenylene terephthalates) (PPT) with NPP side group determined with two different methods, electric-field-induced second-harmonic generation (EFISHG) and hyper-Rayleigh scattering (HRS) methods. Both techniques yield the same values within the experimental errors for pure NPP and NPP-PMMA in 1,1,2,2-tetrachloroethane solution. But the measured results of NPP-PPT polymer in 1,1,2,2-tetrachloroethane solution are showing that the first hyperpolarizability was enhanced with an enhencement of a factor 9.7 in EFISHG and a factor 2.4 in HRS relative to pure NPP. These results indicate that nonlinear optical chromophores organized as side groups of polymers with a rigid backbone contribute coherently to the secondorder nonlinear response of the polymer in the dc electric field as polar polymer chains. hains.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.5
• /
• pp.457-465
• /
• 2011

The fault analysis and detecting algorithm for a 3 phase diode rectifier is proposed. The 3 phase dioderectifier is used for the AC power rectifier of the PWM inverter. The input power or diode faults cause theripples of the DC voltage, degradation of the control performance and life shortening of the DC link capacitor.In this paper, the ripple of the DC voltage is mathematically analyzed for the earth fault of input power andopen circuit fault of the diode, respectively. The fault detection and type of fault can be obtained by comparingthe average DC voltage and the instant DC voltage which is sampled with 6 times of grid frequency. Theproposed method can be easily applicable and doesn't require additional circuit. The experimental and simulationresults are presented to verify the validity of the proposed method.

• Journal of Navigation and Port Research
• /
• v.42 no.6
• /
• pp.427-436
• /
• 2018

In this study, experimental and numerical analysis were performed on the survivability of a long pipe-type buoy structure in waves. The buoy structure is an articulated tower consisting of an upper structure, buoyancy module, and gravity anchor with long pipes forming the base frame. A series of experiment were performed in the ocean engineering basin of KRISO with the scaled model of 1/ 22 to evaluate the survivability of the buoy structure at West Sea in South Korea. Survival condition was considered as the wave of 50 year return period. Additional experiments were performed to investigate the effects of current and wave period. The factors considered for the evaluation of the buoy's survival were the pitch angle of the structure, anchor reaction force, and the number of submergence of the upper structure. Numerical simulations were carried out with the OrcaFlex, the commercial program for the mooring analysis, with the aim of performing mutual validation with the experimental results. Based on the evaluation, the behavior characteristics of the buoy structure were first examined according to the tidal conditions. The changes were investigated for the pitch angle and anchor reaction force at HAT and LAT conditions, and the results directly compared with those obtained from numerical simulation. Secondly, the response characteristics of the buoy structure were studied depending on the wave period and the presence of current velocity. Third, the number of submergence through video analysis was compared with the simulation results in relation to the submergence of the upper structure. Finally, the simulation results for structural responses which were not directly measured in the experiment were presented, and the structural safety discussed in the survival waves. Through a series of survivability evaluation studies, the behavior characteristics of the buoy structure were examined in survival waves. The vulnerability and utility of the buoy structure were investigated through the sensitivity studies of waves, current, and tides.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.4
• /
• pp.325-331
• /
• 1999

In a utility interactive photovoltaic generation system. a PWM inverter is used for the connection between the p photovoltaic arrays and the utility. The dc current becomes pulsated when the conventional inverter system operates i in the continuous current mode and de current pulsation causes the distortion of the accurrent waveform. This paper p presents the reduced pulsation of de input current by operating the inverter with buck-boost chopper in the d discontinuous conduction mode. The dc current which contains harmonic component is analyzed by means of s separating into two terms of a ripple component and a direct component. The constant dc current without p pulsation is supplied from photovoltaic array to the inverter. The proposed inverter system provides a sinusoidal ac c current for domestic loads and the utility line with unity power factor.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.110-117
• /
• 2002

This paper proposes a optimization of the design variables of linear motor for the improvement of thrust. Especially, this paper treats the shoe, which can be good to flow of a magnetic flux in linear motor. Firstly, this paper uses a space harmonic analysis method(SHAM) based on Fourier series, for analyzing the characteristics of core type linear motor, including slot structure and shoe. And compare the magnetic flux densities of linear motor at air gap with the results of the SHAM and the Finite Element Method(FEM). Secondly, this paper uses a genetic algorithm, which is good to find the global solutions. The design variables are the pole pitch of magnet, the pitch of slot, the height of slot, the width of shoe and the width of magnet. The maximum thrust with optimum design variables is about 247 N which is improved about 16%.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.1
• /
• pp.73-81
• /
• 1999

A new slip power recovery system applying a switch mode converter to the rotor circuit of the wound rotor induction machine is proposed and investigated in this paper. With the analysis of the steady-state performances of the proposed system, it can be shown that the speed can be controlled by the duty ratio of the converter switch and the several characteristics of a conventional system can be also improved. In particular, the low power factor and the harmonic components in the line current, which are the main disadvantages of the conventional system, is significantly improved, and linear speed regulation can be obtained. Theoretical and experimental results are presented and illustrated to demonstrate the satisfactory working of the proposed system.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.3
• /
• pp.316-322
• /
• 2009

This paper presents an analytical design method of a passive harmonic filter for a three-phase diode rectifier and uses a new transfer function approach in the analysis and design. The transfer function approach derives an analytical formulation of an utility system including passive filters with a basis of Laplace transform and provides a graphical formulation so that a visualized insight into an interaction between individual filter and system response can be attainted. Harmonic impedance, voltage division and current division transfer function are used as a design tool, which makes a calculated filter parameters to satisfy IEEE-519 distortion limits. A simple five-step design procedure is introduced in the filter design, which consists of system analysis, selection of PCC(Point of Common Coupling), filter specification calculation, appropriate filter design for system and filter implementation. Philosophy governing the design procedure is based on a numerical/graphical iterative solution, trial and error with visualization feed-back based on "algebra on the graph". Finally, performance of the designed passive harmonic filter is verified by experiment and shows that 5th, 7th, 9th, 11th and 13th harmonics are decreased within IEEE-519 distortion limits, respectively.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.12
• /
• pp.622-628
• /
• 2005

This paper is given a full detail of mathematical analyses of input current and output voltage for a novel active type power factor correction (PFC) converter. These are compared with harmonics components of input current for a conventional PFC converter. The proposed PFC converter is constructed in using a new loss-less snubber circuit to achieve a soft switching of control device. Also the proposed converter for discontinuous conduction mode (DCM) eliminates the complicated circuit control requirement and reduces the size of components. The input current waveform in the proposed converter is got to be a sinusoidal form of discontinuous pulse in proportion to magnitude of ac input voltage under the constant duty cycle switching. Therefore, input power factor is nearly unity and the control method is simple. Particularly, the stored energy of loss-less snubber capacitor is recovered with input side and increases input current from resonant operation. The result is that input power factor of the proposed converter is higher than that of conventional PFC converter. Some simulative results on computer and experimental results are included to confirm the validity of the analytical results.