• KSBB Journal
• /
• v.14 no.6
• /
• pp.672-676
• /
• 1999

Encapsulated Aspergillus niger was prepared in order to inspect the effect of oxygen supply on the production of citric acid. A. niger cells which had been immobilized in the calcium alginate capsule grew and mycellia penetrated through the capsule membrane after two days of cultivation and covered over all of the capsule after eight days. The mycellia became loose when the nitrogen source was sufficient of oxygen was deficient. The larger amount of encapsulated cells were put into a given growth medium, the smaller quantity of citric acid was produced. The increase of volumetric oxygen transfer coefficient from 1.8 $hr^-$ to 2.55 $hr^-$ in the flask culture accelerated cell growth rate but did not influence the production of citric acid. The high oxygen supply rate($k_La:\;150\;hr^-$) in the concentric air lift reactor hastened the growth of cells and hindered the production of the citric acid. The reduction of nitrogen source level in the growth medium in the concentric air lift reactor increased citric acid production by 40 percent of that of flask cultivation and the culture period was shortened by 3 days. The variation of the geometry of the concentric air lift reactor did not influence the growth rate of encapsulated cells and production rate of citric acid.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.71-78
• /
• 2006

Sun sensors are frequently implemented by satellites for attitude sensing, due to its simple manufacturability and light weight. A modeling of sun sensors has an important effect on the accuracy of satellite attitude determination. This paper addresses a new modeling of a 2-axis miniature fine sun sensor with improved accuracy. Unlike other previous algebraic modeling methods, the newly suggested physical modeling method takes into account the shadowing effect of the slit thickness. It was shown that a newly proposed sun sensor modeling provides a substantial accuracy improvement of 29% compared to the generic algebraic modeling. The proposed sensor modeling was validated using 2-axis fine sun sensors with FOV(Field of View) of ${\pm}60^{\circ}$ mounted on HAUSAT-2 small satellite, currently under development by SSRL(Space System Research Lab.) at Hankuk Aviation University, Korea.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.1
• /
• pp.37-44
• /
• 2016

This study is concerned with the numerical investigation of dynamic characteristics of 2.5MW-class wind turbine gearbox in which the misalignment improvement of plenary gear shafts by the flexible pins and the dynamic impact response are analyzed by the finite element method. The tooth contact between gears is modelled using the line element having the equivalent tooth stiffness and the contact ratio to accurately and effectively reflect the load transmission in the internal complex gear system. The equivalent tooth stiffness is calculated by utilizing the tooth deformation analysis and the impulse torque is applied to the input shaft for the dynamics response characteristic analysis. Through the numerical experiments, the equivalent tooth stiffness model was validated and the misalignment improvement of planetary gear shafts was confirmed from the comparison with the cases of fixed shafts at one and both ends.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.6
• /
• pp.257-264
• /
• 2013

In this study, we have designed the variable amplitude threshold algorithm that can enhance the accuracy of step count using variable amplitude. This algorithm converts the x, y, z sensor values into a single energy value($E_t$) by using SVM(Signal Vector Magnitude) algorithm and can pick step count out over 99% of accuracy through the peak data detection algorithm and fixed peak threshold. To prove the results, We made the noise filtering with the fixed amplitude threshold from the amplitude of energy value that found out the detection error was increasing, and it's the key idea of the variable amplitude threshold that can be adapted on the continuous data evaluation. The experiment results shows that the variable amplitude threshold algorithm can improve the average step count accuracy up to 98.9% at 10 Hz sampling rate and 99.6% at 20Hz sampling rate.

• The korean journal of orthodontics
• /
• v.38 no.5
• /
• pp.304-313
• /
• 2008

Objective: The purpose of this study was to evaluate the stress distribution in bone and displacement distribution of the miniscrew according to the length and number of the miniscrews used for the fixation of miniplate, and the direction of orthodontic force. Methods: Four types of finite element models were designed to show various lengths (6 mm, 4 mm) and number (3, 2) of 2 mm diameter miniscrew used for the fixation of six holes for a curvilinear miniplate. A traction force of 4 N was applied at $0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$ to an imaginary axis connecting the two most distal unfixed holes of the miniplate. Results: The smaller the number of the miniscrew and the shorter the length of the miniscrew, the more the maximum von Mises stress in the bone and maximum displacement of the miniscrew increased. Most von Mises stress in the bone was absorbed in the cortical portion rather than in the cancellous portion. The more the angle of the applied force to the imaginary axis increased, the more the maximum von Mises stress in the bone and maximum displacement of the miniscrew increased. The maximum von Mises stress in the bone and maximum displacement of the miniscrew were measured around the most distal screw-fixed area. Condusions: The results suggest that the miniplate system should be positioned in the rigid cortical bone with 3 miniscrews of 2 mm diameter and 6 mm length, and its imaginary axis placed as parallel as possible to the direction of orthodontic force to obtain good primary stability.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1990.10a
• /
• pp.173-178
• /
• 1990

로터-베어링축계는 증기및 가스터빈, 터보 발전기, 압축기등 거의 모든 산업 기계류에서 동력 전달의 기본 도구로써 사용되고 있다. 즉 회전에 의한 동력 의전달은 비교적 간단히 대용량의 동력을 효율적으로 전달할 수 있다. 이에 따라 회전기계류에 대한 연구는 산업 혁명 이후 꾸준히 발전되어 온바, 특히 근래에 들어와 산업기계류의 경쟁이 치열하여짐에 따라 산업기계류의 고정 밀화, 고속화, 고신뢰화 요구가 증대하고 있는 현실을 비추어 볼때, 산업 기 계류의 근간을 이루고 있는 로터-베어링 축계의 안정성을 포함한 진동에 관 한 문제는 회전기계류 설계의 주요 기술로써 연구.개발의 필요성이 매우 높 다 하겠다. 회전축계 진동 관련 연구는 두 분야로 대별될 수 있는데 언밸런 스(Unbalance)에 의한 Synchronous진동과 여러가지 원인에 의해 계의 불안 정성을 유발시키는 Nonsynchronous진동으로 나눌 수 있다. 본 연구에서는 이들 연구의 기본이 되는 회전축-베어링계 동특성 해석 프로그램을 개발하 였다. 여러가지 방법이 있으나 여기서는 Holzer가 비틀림 진동에 적용하고, Mykiestad(2)와 Prohl(3)에 의하여 회전축의 횡 진동에 적용된 이후 Lund(4) 등에 의하여 베어링의 영향등이 첨가된 전달 매트릭스 (Transfer Matrix) 방 법을 이용하여 임계속도(Critical Speed), 모우드 형태(Mode shapes)를 예측 하고 불안정 판정(Instability Criteria)등을 할 수 있는 프로그램을 개발하였 다. 특히 Murphy(1)의 다항식 방법(Polynomial Method)에 기본을 두어 기존 의 전달 매트릭스가 가지고 있던 반복, 수렴 시간 문제와 빠뜨리는 임계속도 예측에 대한 개선을 이루었으며 기존 논문과 실험 결과와의 비교 검토를 통 하여 개발된 프로그램의 신뢰성을 검토하였다. 특히, 각종 회전 기계의 소형 화, 경량화 추세에 따라 지반이나 케이싱이 경량이거나 유연하여 회전축과 동적으로 연성된 경우 회전축-베어링-지반으로 이루어진 2중구조의 회전축 계 동특성을 해석할 수 있는 프로그램을 개발하므로서 회전 기계류의 진동 전반에 걸친 문제점에 대한 그 원인과 현상을 명확히 분석하여 국내의 전기 계류의 보다 신뢰성있는 설계 및 제작자료를 확보하는데 기여할 수 있게 하 였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.4
• /
• pp.423-429
• /
• 2013

The performance of a vertical-type wind power generator system was predicted by CFD analysis. In the analysis, the reaction torque was calculated for a given rotational speed of the blades. The blade torque of a wind power system was obtained for various rotational speeds, and the generation power was calculated using the obtained torque and the rotational speed. The optimum generator specification, therefore, could be decided using the relationship between the generated power and the rotational speeds. The effects of the number of blades and blade shapes on the generation power were also investigated. Finally, the analysis results were compared with the experimental results.

• Journal of Energy Engineering
• /
• v.11 no.4
• /
• pp.299-305
• /
• 2002

The present experimental and numerical investigations are performed on the characteristics of transitional flow in a concentric annulus with a diameter ratio of 0.52, whose outer cylinder is stationary and inner one rotating. The pressure losses and skin-friction coefficients have been measured for the fully devel-oped flow of water and that of 0.2％ CMC-water solution at a inner cylinder rotational speed of 0∼600 rpm, respectively. The transitional flow has been examined by the measurement of pressure losses to reveal the relation of the Reynolds and Rossby numbers with the skin-friction coefficients. The occurrence of transition has been checked by the gradient changes of pressure losses and skin-friction coefficients with respect to the Reynolds numbers. The increasing rate of skin-friction coefficient due to the rotation is uniform for laminar flow regime, whereas it is suddenly reduced for transitional flow regime and, then, it is gradually decreased for turbulent flow regime.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.5
• /
• pp.83-90
• /
• 1999

In this paper, we studied resolution to the FBP and BFP image reconstruction algorithms for ultrasonic diffraction tomography. In order to analyze the resolution to the tomographic images which can be reconstructed from the modified FBP image reconstruction algorithm by using fixed coordinate system and BFP image reconstruction algorithm which is suitable for plane structure object, we derived ambiguity functions to these algorithms and then analyzed lateral and depth resolution through simulation respectively. Simulation results show that the lateral and depth resolution to the FBP image reconstruction algorithm and the BFP image reconstruction algorithm was determined 0.27 λ, 0.70 λ and 0.39 λ, 0.98 λ at the 3dB respectively. These results imply that modified FBP and BFP image reconstruction algorithms for diffraction tomography is useful in the tomographic image reconstruction.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.12
• /
• pp.1160-1165
• /
• 2011

This study is focused on the structural dynamic responses, i.e., vibration analysis results of the high-accuracy observation multi-axial camera, which is installed and operated for the UAV (Unmanned Aerial Vehicle) and helicopter etc. And, the authors newly suggest a modeling technology of the ball bearing applied to the camera by using three-axis spring elements. The vibration analysis results well agreed to the randum vibration test results. Also, the vibration responses characteristics of the multi-axial camera through the time history analysis of the random vibration were analyzed and evaluated. The above results can be applied to the FE-modeling of the ball bearings used for the space cameras.