• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.275-282
• /
• 2002

High fluidity concrete needs high dosage of superplasticizer to acquire sufficient fluidity and high contents of fine powder and viscosity agents to prevent segregation. But it requires high manufacturing cost and has difficult in quality control. Therefore, in this paper, determination of optimal mixture proportion of segregation type superplasticizer for high fluidity concrete and manufacturing high fluidity concrete by applying developed segregation reducing type superplasticizer are discussed using flowing concrete method. According to test results, as dosage of superplasticizer increases, it shows that fluidity and bleeding increase, while air contents and ratio of segregation resistance decrease. It also shows that adding viscosity agent into it reduce bleeding and improve segregation resistance. Dosage of AE agent into it containing viscosity agent recovers loss of air contents during flowing procedure. Combination of proper contents of superplasticizer, viscosity agent and AE agent make possible to develope segregation reducing type superplasticizer Compressive strength of high fluidity concrete applying flowing method with it is higher than that of base concrete. No differences of compressive strength between compacting methods are found.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.515-516
• /
• 2011

송 배전 및 정보통신 설비, 건축물 등 모든 분야의 설비 및 인명 보호를 위해서는 반드시 필요하고 중요한 것이 접지이며, 접지 설계 시 대상 부지의 정확한 대지고유저항을 측정, 분석하는 것은 가장 중요하다고 할 수 있다. 본 대지고유저항 분석시스템은 이렇듯 중요한 대지고유저항을 기존의 수작업 분석방법이 아닌 시스템 반복계산에 의한 최적 curve 분석방법을 도입, 측정값의 신뢰도 평가 등을 이용한 측정값 분석으로, 분석값의 정확성을 높이고 분석시간을 단축함으로서 보다 정확하고 신속한 접지설계를 가능하도록 한다.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.32 no.1
• /
• pp.21-27
• /
• 1995

초고속선에 관련된 점성유동은 저한성능 향상과 운항자세 제어를 위해 사용되는 다양한 선체부 가물의 저항 예측과 초고속선에 많이 사용되는 물분사 추진장치 입구 형상의 설계 그리고 임펠 러에 이르는 덕트 유동의 예측을 중심으로 관심을 받아왔다. 본 소고에서는 통상적인 선박의 경우와는 구별되는 초고속선 고유의 점성유동 특성에 관하여 간략히 논의하기로 하고 내용을 크게 선체-부가물 점성유동과 물분사 추진장치에 관련되어 있는 덕트유동으로 나누어 기술하 였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.9-15
• /
• 2018

According to the development and use of self-consolidating concrete in field, interest in material properties of early-age concrete is rising. Setting time with hydration process of cement is one of significant indicator to evaluate the early-age material properties of concrete, various nondestructive methods including penetration resistance measurement have been proposed to estimate setting time. This study performed an experimental approach to evaluate setting time delay in mortar adding superplasticizer using electrical resistivity measurement. For this purpose, total nine types of mortar samples were prepared, and its electrical resistivity was monitoring during 24h after mixing. From the experimental result, rising time of electrical resistivity was used to evaluate setting delay of mortar, and penetration resistance was also measured for comparison. In addition, dynamic elastic modulus and compressive strength of 1day mortar were measured to investigate a possibility the use of electrical resistivity measurement for evaluation of early-age material properties.

• Journal of Navigation and Port Research
• /
• v.38 no.4
• /
• pp.335-341
• /
• 2014

Faced with global agenda of greenhouse abatement program including regulations and $CO_2$ emission trading scheme, shipping companies are enforced to a high level of efficiency in fuel consumption. Accordingly shipbuilding companies worldwide are required to develop fuel-efficient ships which otherwise traditionally consume a great amount of fossil fuels. In this dissertation, relevant to the improvement of fuel efficiency for commercial ships, design methodology through the numerical simulations are intensively described. This work consists of derivation of effective hydrodynamic design practice based on the application of longitudinal grooves to effectively improve the pressure distribution around ship hull. The primary objective of the present study is to improve ship resistance performance using longitudinal grooves which originate from long strips on the abdomen of humpback whale. Several groove shapes have been extensively investigated and the proposed shape efficiently controlled the variation of pressure distributions acting on the hull surface.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1244-1249
• /
• 2002

In this study, the physical characteristics of steel-wire sound absorbing materials with different thickness and bulk density is experimentally obtained in terms of the porosity and specific flow resistivity. Based on the experimental results, the following conclusions can be made. The porosities of steel-wire sound absorbing materials are smaller than those of general absorbing materials, which are inversely proportional to the volume densities. For the porosity measurement with a good accuracy, the dynamic correction based on the system compliance should be involved in porosity measurement. In addition, the flow condition for the precise measurement of the specific flow resistivity of steel-wire sound absorbing materials should be limited in the laminar flow region.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1347-1352
• /
• 2001

In this study, the acoustic properties of polyester sound absorbing materials with three different bulk densities were investigated by calculating and measuring the acoustic parameters in terms of characteristic impedance, propagation constant, and absorption coefficient. For the calculations, Delany and Bazley's empirical equation was used together with the experimentally obtained specific flow resistivities under steady flow conditions. For the experimental measurements, the well-known two-thickness method was accessed. The experimentally measured values of characteristic impedance and propagation constant were generally agreed well with the corresponding calculated values. Based on the comparisons between the calculations and measurements, it was found that the magnitude of the absorption coefficient was closely related to the characteristic impedance and the real part of the propagation constant. Especially, the maximum magnitude of the absorption coefficient was depended upon the imaginary part of the propagation constant indicating the phase change of the propagation constant.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.162-166
• /
• 1998

Synthetic fluid, class 7 group 2, as an insulating and cooling material is selected as. specimen, arid it is studied for the physical and electrical properties. Also, Benzotriazole(following as BT A) known as a suppressant of streaming electrification is added to it, and the change of physical and electrical properties by addition of BT A is investigated. From the spectrum of FT-IR, it is confirmed that the absorption peak in wavenumbers $3400{\sim}3450[cm^{-1}]$ is small or disappears when BTA is added. AC breakdown strength and volume resistivity of each specimen are investigated. It is considered that the effective content of BTA is about 10[ppm] for the suppression of electrification in this experiment.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.267-269
• /
• 1997

The electrical properties due to the Benzotriazole(following as BTA) additive in fluids for insulating and cooling the ultra-high voltage transformer is studied in this paper. Specimen having the several contents of BTA, such as 5[ppm]. 10[ppm] and 30[ppm] is used in order to investigate the characteristics on volume resistivity in case of fluid flow in experimental device made in lab. Volume resistivity is decreased with an increase of fluid flow velocity and increased with BTA content in low temperature region, but volume resistivity of specimen contained BTA 10[ppm] is the largest thing over $30[^{\circ}C]{\sim}50[^{\circ}C]$ than the others in experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.4
• /
• pp.423-429
• /
• 2012

Miller cycle is considered as an effective means to meet the regulation on Tier II and to reduce $CO_2$ emission. For this cycle, the amount of intake air supplied should be enough increased. Therefore, the intake system with minimized resistance for air flow is under consideration. In this study, the flow coefficients of intake valves were measured in order to obtain the basic data for the cycle simulation and intake port design. The flow coefficients were measured using the steady-flow test rig. As a test result for the poppet valve used the marine engine with medium speed, the flow coefficients are increased to about 0.62 with the valve lift. In addition it is confirmed that the flow coefficients have the characteristic value irrelevant to the S/B ratio.