• Journal of computational fluids engineering
• /
• v.21 no.4
• /
• pp.85-89
• /
• 2016

Wing is the most important part of aircraft which produces lift. In general when aircraft takes off or lands, high lift is required and additional devices are adopted in front and aft-side of wing, which constitute so-called multi element airfoils. The objective of this research is to develop a specialized grid generation program to help engineers in reducing human labor and eliminating time-consuming process for mesh regeneration by deforming the initially-given grid system with efficient deforming method. This paper describes briefly about the mesh deformation methods, and provides some results to verify the quality of deformed mesh and eventually correctness of current approach.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.206-209
• /
• 2011

During landing approach, an airplane could experience dynamic unstable motion by the combination of a gust and elevator control to cancel the disturbances. This situation is dangerous and could lead to a loss of an airplane. In this paper, numerical analysis was used to study the effect of pitch oscillating 2-D high lift devices in a landing condition. Experimental data on a pitching naca0012 airfoil was used for code validation. Dynamic characteristics of an airfoil, single slotted flap for mid-class passenger aircraft were analyzed. Unsteady Navier-Stokes analysis was performed with Spalart-Allmaras turbulence model for separation dominant low speed flow. As a result, flow hysteresis of a flapped airfoil was more complex than that of an oscillating airfoil. So, dynamic analysis of a flap in a landing condition is very important for operational safety.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.58-62
• /
• 2016

본 연구에서는 지면효과의 영향을 비행체의 형상에 따라 비교하기 위해 에어포일, 플랩을 장착한 에어포일 그리고 플라잉디스크를 EDISON_CFD를 통해 해석하고자 한다. 받음각 $0^{\circ}$, $5^{\circ}$, $10^{\circ}$에 대하여 마하수 0.18, 단위 길이 당 레이놀즈수 $3.78{\times}10^{-5}/m$의 유동조건에서 2차원 범용 소프트웨어인 KFLOW_EDISION_13의 S-A Turbulent Model을 이용하여 지면과의 높이를 형상 코드길이를 기준으로 0.25c, 0.5c, 1c, 3c로 변경하면서 해석을 수행하였다. 그 결과 세 형상 모두 일반적인 지면효과인 지면과 가까울수록 양력계수는 증가, 항력계수는 감소하여 양항비가 증가하는 경향을 보여주었다. 하지만 일부 예외적인 부분을 확인하여 분석을 실시하였다.

• Journal of Aerospace System Engineering
• /
• v.7 no.3
• /
• pp.1-6
• /
• 2013

Numerical optimization of two dimensional high lift configuration was performed with flow solver and optimization method based on RSM(Response Surface Model). Navier-Stokes solver with Spalart-Allmaras turbulence model was selected for the simulation of highly complex and separated flows on the flap. For the simultaneous optimization of both flap shape and setting (gap/overlap), 10 design variables (eight variables for flap shape variation and two variables for flap setting) were chosen. In order to generate the response surface model, 128 experimental points were selected for 10 design variables. The objective function considering maximum lift coefficient, lift to drag ratio and lift coefficient at specific angle of attack was selected to reduce flow separation on the flap surface. The present method was applied to two dimensional fowler flap in landing configuration. After applying the present method, it was shown that the optimized high lift configuration had less flow separation on the flap surface and lift to drag ratio was suppressed over entire angle of attack range.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.78-83
• /
• 2010

In the present paper, a flap was optimized to maximize the lift. A 2-element fowler flap system was utilized for optimization with an initial shape of general aviation airfoil and a flap shape designed by Wentz. Response surface method and Hicks-Henne shape function were implemented for optimization. 2-D Navier-Stokes method was used to solve flow field around aGA(W)-1 airfoil with a fowler flap. Commercial programs including Visual-Doc, Gambit/Tgridand Fluent were used. Upper surface shape and the flap gap were optimized and lift for landing condition was improved considerably. The original and optimized flaps were tested in the KARI's 1-m low speed wind tunnel to examine changes in aerodynamic characteristics. For optimized flap tests, the similar trend to prediction could be seen but stall angle of attack was lower than what was expected. Also, less gap than optimized design delayed stall and produced better lift characteristics. This is believed to be the effect of turbulence model.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.5
• /
• pp.10-16
• /
• 2003

To investigate the jet effect on circulation control, a segment of model was prepared and inserted horizontally across the test section of the cavitation tunnel. The hydrodynamic forces acting on the model were measured under the 2 dimensional flow behavior. Circulation flow control requires higher flow rate of water jet than boundary layer control does. Jet injection is effective in increasing lift coefficient and the increments reach to 160% in a certain combination of parameters such as an angle of attack, jet flow rate and flap angle. The blown water jet not only reduces form drag but also thrust effect, which is sometimes greater than the form drag in specific conditions.

• Journal of computational fluids engineering
• /
• v.16 no.4
• /
• pp.47-54
• /
• 2011

A rotating propeller of turboprop aircraft gives much effect on the aerodynamic characteristics of wing such as lift, moment and stall. Specially propeller effect on the wing surface is much more dominant when aircrafts are in landing or take-off conditions. In the present paper, three dimensional Navier-Stokes simulations for the interaction of propeller and wing were carried out for medium sized turboprop aircraft. For rotating propeller, unsteady sliding mesh method was used to simulate a relative motion between moving and static bodies. For the power effect analysis in landing and take off configurations, double slotted flap was also considered and the aerodynamic characteristics were investigated. It was shown that the propeller slipstream enhanced the lift slope including maximum lift by eliminating local flow separation region and this enhancement was more dominant with high lift device.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.6 s.237
• /
• pp.755-762
• /
• 2005

To evaluate the aerodynamic efficiency of TR-S2 configuration designed by SUDC, wind tunnel tests of $40\%$ scaled model were done in KARI LSWT. The aerodynamic characteristics of plain and Semi-Slotted Flaperon were compared, and vortex generators were installed to improve flow pattern along the wing surface. Effects of the control surface such as elevator, rudder, aileron, and incidence angle of horizontal tail are measured for various testing conditions. Test results showed that Semi-Slotted Flaperon produced more favorable lift, lift/drag, and stall margins and application of vortex generator would be best choice to enhance wing performance. Longitudinal, lateral and directional characteristics of TR-S2 were found to be stable for the pitch and yaw motions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.6
• /
• pp.10-17
• /
• 2006

NACA23012익형에 대하여 synthetic jet을 이용하여 박리 제어를 수행하였다. 공력특성의 향상을 위해 앞전 droop과 plain flap의 박리 부근에 synthetic jet을 위치시켰다. 고 받음각에서 앞전 박리의 발생으로 인한 실속을 앞전 droop의 작동과 이때 발생하는 앞전 박리를 synthetic jet으로 효과적으로 지연시킬 수 있고, 또한 실속 특성을 개선 할 수 있음을 확인하였다. 양력의 향상을 위하여 plain flap을 장착하였고, 이때 발생하는 박리를 synthetic jet으로 지연시켜 제어면의 작동 효율을 증가 시킬 수 있음을 확인하였다. 앞전 droop과 plain flap으로 구성된 간단한 고양력 장치에 발생하는 박리를 synthetic jet으로 제어함으로 실속을 지연시킴과 동시에 실속 특성을 향상시키고, 최대 양력의 증가로 fowler flap에 버금가는 공력특성을 확보할 수 있음을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.10 s.253
• /
• pp.1012-1018
• /
• 2006

To evaluate the aerodynamic efficiency of TR-S4 configuration, wind tunnel tests of 40% scaled model were done in KARI LSWT. TR-S4 configuration has different nacelle shape, larger EO/IR camera and aftward wing location compared with TR-S2. Component build-up test after adding each element of model is performed. Also effects of horizontal tail incidences, Flaperon and Aileron deflection. on aerodynamic characteristics are measured. Test results showed that TR-S4 configuration has favorable stability characteristics in longitudinal, lateral and directional for the pitch and yaw motions.