• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.11-11
• /
• 2000

액체렘제트 엔진에서는 고온·고속의 공기가 공기흡입구로 유입되기 때문에 고성능 램제트 연소기의 설계를 위하여 실제 비행조건을 모사할 수 있는 고온 고속의 공기 발샐장치가 필요하다. 본 연구에서는 수소연소에 의해 Vitiated Air를 발생시키도록 설계된 Vitiated Air Heater(VAH)를 제작하였으며, VAH의 성능평가를 통하여 80∼120m/s 와 400∼800K 범위에서 손쉽게 속도와 온도의 조절이 가능하고 균일한 속도 및 온도분포로 대기공기와 같은 Vitiated Air를 얻을 수 있었다. 그리고 VAH을 연결하여 Dump형 연소기의 특성을 실험하였다. 액체 램제트 엔진에 있어서 공기흡입구가 하나인 Dump형 연소기에 주요변수로서 흡입공기의 온도와 공연비를 변화시키면서 연소기내의 화염형상을 관찰하고, 온도분포를 계측하였으며 Injection 위치에 따른 화염현상을 관찰하였다. 각 경우의 연소효율을 계산하여 실험범위에서의 최적 연소조건을 제시하였다.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.612-617
• /
• 2015

초음속 흡입구는 고속 비행에서 발생하는 충격파를 이용하여 제트엔진 내부에 유입되는 공기를 압축시키는 구조로써 주로 램제트와 스크램제트 엔진에 적용되어 연구개발이 진행되어 왔으며 현재는 미사일의 추진체 개발에도 응용되고 있다. 초음속 영역에서의 흡입구는 cone 모양의 스파이크 구조를 통해 경사충격파가 생성되어 외부에서의 공기압축을 먼저 거치게 된다. 본 연구에서는 EDISON CFD를 이용하여 외부압축 초음속 흡입구 주위의 공기유동을 해석하고 Cubbison, R.W.의 풍동실험 결과와 비교 분석하였다. 초음속 흡입구 주위의 유동을 2D 축대칭 압축성 유동으로 가정하고 EDISON CFD의 2D_Comp_P 솔버를 사용하여 수치해석을 수행하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.13-13
• /
• 2000

램제트 엔진에 대한 기초 연구로서 양쪽 대칭의 공기 흡입구를 갖는 2차원 형태의 램제트엔진 연소기를 제작하여 그 특성을 분석하였다. 실험은 흡입공기의 연소실내 유입각도와 연소실내의 도움 위치에 따른 연소실 형상을 바꾸어가며 연소기내의 유동특성을 살펴보았다. 이를 위하여 고속 유동장의 2차원 평면 속도 분포를 측정할 수 있는 two color PIV 기법을 개발하였다. 이 기법은 다른 색의 두 레이저빔을 사용하여 방향성의 문제를 해결하며, 이미지의 색 분리에 따른 거의 완벽한 cross-correlation이 가능하며 높은 single-to-noise 비를 얻게 됨으로써 dynamic range의 증가가 가능해지며, 조사 영역 안에 존재해야 하는 입자 쌍의 수가 줄어들게 된다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.1
• /
• pp.67-83
• /
• 2005

The evolution of hypersonic scramjet engines was reviewed from the 1960s to the present. Concepts of hypersonic air-breathing propulsion systems based on scramjet engine, such as combined-cycle engine, were described and compared with other high-speed propulsion systems. The development history of scramjet engines over the past 40 years odd was introduced with priority given to the efforts in the United States, and the current status of scramjet technology was reviewed through the recent development programs in several developed countries.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.115-128
• /
• 2006

A technical analysis of current scramjet and combined-cycle engine is presented. Substantial research has been pursued to characterize the operation mechanism of scramjet propulsion, especially in the areas of flame stabilization and system integration, dramatically over the years in support of both military and space access application. Major technology that had significant impact on the maturation of scramjet propulsion technology are dual combustion ramjet, dual mode ramjet, and combined cycle engine to cover a typical wide rage of flight, up to flight Mach number 10. Notable are the fundamental and practical techniques, for instance, scram propulsion itself, thermal relaxation and protection using endothermic fuel and/or CSiC composit materials, and design/manufacture of movable intake and nozzle, to realize high speed propulsion system in near future.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.95-104
• /
• 2002

A two color PIV technique has been developed for visualization of complex and high speed flow in a ramjet combustor. Two color PIV has the advantages that velocity distribytions in high speed flowfields can be measured simply by varying the time interval between two different laser beams and a directional ambiguity problem can be solved by color separation, and then a singnal-to-noise ratio can be increased through nearly perfect cross-correlation. As a basic research of the ramjet engine, a 2-D shaped combustor with two symmetric air intakes has been manufactured and an experimental study has been conducted using a two color PIV technique. The flow characteristics such as recirculation zones and two intake air mixing have been investigated varying inlet angles and dome heights. It is found that the size and air mass ratio of reciculation zones are affected mainly by an inlet angle, but not much by a dome height.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.197-207
• /
• 2004

The developing Smart UAV in KARI supposes high speed flight as like a conventional plane, as well as vertical takeoff and landing as like a helicopter. Therefore, the air intake system should be designed to provide the sufficient air flow to the engine and the maximum possible total pressure recovery at the engine intake screen over a wide range of flight conditions. For this purpose, we designed the intake system using a pitor type intake model and plenum chamber. In this paper, we designed the intake model and analyzed the performance of designed intake system using the general-purpose commercial CFD code, CFD-ACE+. The analysis results of the total pressure variation and the velocity distribution were illustrated in this paper. The pressure recovery and distortion coefficient at a plane coincident with the compressor inlet were calculated and streamline variation through the intake system was investigated at the worst flight condition as well as the standard flight condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.54-63
• /
• 2006

Ejector system are used to transport a low momentum flow to the higher pressure flow by the momentum change between high and low momentum flows. This system is used to simulate the high altitude and Mach number condition over altitude 20 km and Mach 4 of the supersonic test facility. We applied the design and the performance analysis technique(EISIMP code) of the Ramjet Test Facility(RJTF) air system in JAXA to the ejector system of the ramjet test facility in KARI. After preliminary design of the ejector system, we performed a computational study using FLUENT and investigated shock structures and flow characteristics of the ejector system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.3
• /
• pp.67-75
• /
• 2019

The laminar burning velocity of endothermic fuel surrogates is measured in this study, in order to investigate combustion characteristics of aviation fuel after being used as coolant in an active cooling system of a hypersonic flight vehicle. A Bunsen burner was manufactured such that the laminar burning velocity can be taken for two types of surrogate fuels, SF-1 and 2. The results showed that the burning velocity of surrogate fuels was faster at high equivalence ratio conditions than that of the reference fuel (RF), and specifically, the velocity of SF-1 had the maximum value at the highest equivalence ratio compared with those of SF-2 and RF.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.72-86
• /
• 2006

A technical review of current ramjet propulsion is presented. In addition to summarize the current status of ramjet technology, new key techniques like Boosting technique easily adapting total impulse of booster, flame stabilization technique with minimized ramjet combuster length, variable nozzle-inner-surface technique realizing wide flight-envelop, and thermal protection technique for long operating time are identified. Actually various Ramjet propulsion technology has been matured and expanding to both military and combined cycle application. Yet many opportunities remain to be challenged by future generations of explorers to utilize s typical ramjet propulsion system for multi-purpose(multi-platform and multi-target) missiles, for example, American JSSCM and Russian Yakhont missiles, improving both reliability of techniques and downsizing development cost of new propulsion system.