• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.5-17
• /
• 1995

기술과 과학이 끊임없이 발달되고 있는 가운데 생산기술과 생산공업도 비약적으로 발달되고 있다. 공작기계에 대한 요구사항은 일반적으로 고정도화, 고속도화 그리고 고능률화 나아가서는 자동화이다. 다시 말해서 더욱 좋은 품질(고정도화)과 저렴한 가격(고능률화)의 제품을 빨리 사용자에게 공급(고속화)할 수 있고, 다양한 제품을 만들 수 있는 공작기계가 요구되는 것이다. 고능률화 또는 고속화를 위해서는 고속절삭가공을 실현해야하며 그러기 위해서는 Spindle(주축)의 회전수를 높이고 각 축의 이송 속도가 빨라야 되며 절삭 이송을 고속화하여야 한다. 그리고, 머시닝센터에서는 공구를 자동으로 교환하는(ATC)을 신속히 해야 한다. 이와 같은 고속 공작기계에 대한 요구는 점점 많아지고 있으며 공작기계전시회가 열릴때마다 고속도화는 점점 진전되고 있다. 최근에는 주축의 회전수가 10,000$min^{-1}$은 보통이고 최고 40,000$min^{-1}$이상에 도달하고 있다.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.38-47
• /
• 2002

Machining quality has been improved with the development of cutting tools. However, it is difficult to obtain a high degree of quality in machining a deep pocket with a long end mill, since machining accuracy is mainly dependent on the stiffness of the cutting tool and tool holder. To improve machining quality in machining a deep pocket using an end mill, the performance by cutting condition compare with others. Owing to this problem, it is necessary to select suitable tool and holder in the deep pocket machining. In this study, the hydraulic holder for the high speed machining is introduced and the performance of that is compared with others according to cutting conditions. The cutting parameters involved were; slenderness ratio in the range of 3 to 6 (L/D), radial depth of cut from 0.01 to 0.05 mm. Cutting force and surface roughness, precision of form were observed during the experiment to investigate cutting state.

• 한국기계가공학회지
• /
• 제10권5호
• /
• pp.20-25
• /
• 2011

In this paper, we reviewed the spindle system's motor and bearing and its mode safety for optimal design of a high speed spindle system that exceeds DmN value of 1,500,000. We could verify that it has a separation margin during critical speed by performing critical speed analysis. Also, we have selected an optimal sensoring installation location and actually manufactured & installed the sensor by identifying the stress concentration position in the axial load through finite element analysis to install the built-in piezo electric type load sensor to the spindle housing that can measure and monitor the machining load during high speed rotation of the spindle. Reproducibility is also verified by calibrating the error through the sensor's sensitivity adjustment after comparing the output between the plate dynamoneters and the load sensor to confirm the reproducibility of the load sensor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.115-119
• /
• 1992

산업의 발전과 더불어 새로운 재료의 개발에 대한 요구가 날로 증가하고 있으며 이와 같은 요구에 부응하기위하여 각종의 신소재가 개발되고있다. 이들 신소재 중에서 섬유강화 복합재료는 높은 비탄성과 비강도특성 때문에 구조물의 경량화가 요구되는 우주선, 항공기 등에 주로 이용 되어 왔으며 최근에는 복합재료의 가격이 저렴해 지면서 이 재료의 높은 비탄성과 감쇠특성을 이용하고자 스포츠용품 및 기계 부품에도 섬유강화 복합재료의 이용이 증가 되고 있다. 항공기나 고속회전체의 부품을 복합재료로 제작하였을 경우 복합재료를 다른 금속이나 다른 복합재료부품에 접합(joining)시켜야 하는데 이 때문에구조물의 효율은 Joint에서 주로 죄우된다. Joint를 제작하기 위해서는 복합재료의 표면을 가공한 수 Adhesive를 이용하거나 Bolt로 체결하기 위해 구멍 뚫기 작업이 필요하여 드릴링을 하였을때 이 재료가 매우 연마성이 강하여 심한 공구마멸을 일으키며, 드릴의 입구와 출구쪽에서 각 ply들의 박리 현상이 발생하고, 드릴가공된 벽면으로부터 섬유 또는 레진의 탈락현상등이 발생하는 결점을 가지고 있다. 따라서 본 연구에서는 이러한 결점을 최소화하여 고정밀도의 높은 생산성을 얻기위한 가공기술에 대한 자료를 만들고 최적 절삭조건 및 복합재료가공용 드릴의 설계를 위한 지침을 제시하고자 고속도강 표준드릴을 사용하여 유리섬유 에폭시 복합재료및 탄소섬유 에폭시 복합재료의 드릴링 실험에서 절삭조건이 가공면 생성, 공구마멸, 절삭력에 미치는 영향에 대하여 조사하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.343-348
• /
• 2000

The term‘High Speed Machining’has been used for many years to describe end milling with small diameter tools at high rotational speeds. typically 10,000 - 100,000 rpm. The process was applied in the aerospace industry for the machining of light alloys, notably aluminium. In recent years, however, the mold and die industry has begun to use the technology for the production of components, including those manufactured from hardened tool steels. And the end-mill is an important tool in the milling process. A typical examples for the end mill is the milling of pocket and slot in which a lot of material is removed from the workpiece. Therefore the proper selection of cutting parameters for end milling is one of the important factors affecting the cutting cost. The one of the advantages of HSM is cutting thin-wall part of light alloy like Al (thinkness about 0.3mm). In this paper, firstly, we study characteristics of HSM, and then, we choose the optimal parameters(cutting forces) and investigate various machining strategies to cut thin-wall part by experiment.

• 한국정밀공학회지
• /
• 제16권5호통권98호
• /
• pp.11-18
• /
• 1999

Recently high speed machining is being studied actively to reduce machining time and to improve machining precision. To perform efficient high speed machining, evaluation of high speed machinability must be studied preferentially and it can be identified by investigation of cutting force. To measure cutting forces in high speed machining, dynamometer which has high natural frequency was newly designed using 3-axes piezo force sensor. For newly designed dynamometer, calibration is conducted with sensitivity of force sensor modulated and proper preload and interference force are investigated experimently. Also, cutting force signals of newly designed dynamometer are compared with those of conventional one in high speed cutting experiment and its superiority is confirmed. Then using newly designed dynamometer, high speed machinability is evaluated about cutting force and tool wear in various cutting conditions.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.84-89
• /
• 2001

In recent years, there is increasing demand of esthetic design and complex function in aerospace, automobile and die/mold industry, which brings into limelight high-precision, high-efficient machining of sculptured surface. This paper deals with the establishment of the optimal tool path on free form surface in high speed ball end milling. Ball end milling is widely used for free form surface die and mold. In this machining, the cutting direction was changed with tool path. The cutting characteristics, such as cutting force and surface form are varied according to the variation of cutting directions. In this paper, the optimal tool path with down cutting in free form surface cutting is suggested.

• 한국기계가공학회지
• /
• 제5권4호
• /
• pp.59-64
• /
• 2006

High Speed Machining(HSM) reduces machining time and improves surface accuracy because of the high cutting speed and feedrate. Development of HSM makes it allowable to machine difficult-to-cut material and use small-size-endmill. It is however limited to cutting condition and tool material. In the machining operation, it is important to check main parameter of tool life and select optimal cutting condition because tool breakage can interrupt progression of operation. In this study, cutting parameters are determined to 3 factors and 3 levels which are a spindle speed, a feedrate and a width of cut. Experiment is designed to orthogonal array table for L9 with 3 outer array using Taguchi method. Also, it is proposed to inspect significance of the optimal factors and levels by ANOVA using average of SN ratio for tool life. Finally, estimated value of SN ratio in the optimal cutting condition is compared with measured one in the floor shop and reduction of loss is predicted.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.81-86
• /
• 2010

This paper investigated into process characteristics of AlTiN coated layers for machining to the direction of upper and lower in plastic mold material (KP-4) with the cemented carbide ball endmill with the diameter of 8mm coated AlTiN layers (1~4) step by step using machining center. The material used in experiments was KP-4 that was machined by three types of inclined angles; $15^{\circ}$, $30^{\circ}$ and $45^{\circ}$ As estimated mechanical properties of AlTiN coated layers, it was shown the most result in the condition of three layered coating that the coating that the coating depth, the hardness of the coated layer and the surface roughness of the coated layer were $13{\mu}m$, Hv 3027.3 and $0.042{\mu}m$, respectively. The cutting component was better at the condition of upper direction than that of lower direction in all experimental conditions and indicated to be less which the bigger angle of the material was increased the effective diameter of the tool.

• 한국기계가공학회지
• /
• 제21권5호
• /
• pp.34-39
• /
• 2022

The ion implantation technology changes the chemical state of the surface of a material by implanting ions on the surface. It improves the wear resistance, friction characteristics, etc. Plasma ion implantation can effectively reinforce a surface by implanting a sufficient amount of plasma nitrogen ions and using the injection depth instead of an ion beam. As plasma ion implantation is a three-dimensional process, it can be applied even when the surface area is large and the surface shape is complicated. Furthermore, it is less expensive than competing PVD and CVD technologies. and the material is The accommodation range for the shape and size of the plasma is extremely large. In this study, we improved wear resistance by implanting plasma nitrogen ions into a carbide end mill tool, which is frequently used in high-speed machining