• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4D
• /
• pp.511-518
• /
• 2011

Truck weight data are essential for road infrastructure design, maintenance and management. WIM (Weigh-In-Motion) system provides highway planners, researchers and officials with statistical data. Recently high speed WIM data also uses to support a vehicle weight regulation and enforcement activities. This paper aims at developing axle load estimating models with high speed WIM data collected from national highway. We also suggest a method to estimate axle load using simple regression model for WIM system. The model proposed by this paper, resulted in better axle load estimation in all class of vehicle than conventional model. The developed axle load estimating model will used for on-going or re-calibration procedures to ensure an adequate level of WIM system performance. This model can also be used for missing axle load data imputation in the future.

• 한국ITS학회:학술대회논문집
• /
• 2010.05a
• /
• pp.151-156
• /
• 2010

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.15-16
• /
• 2010

The field experiments and analyses were performed to apply Post-Tensioned Prestressed Concrete Pavement(PTCP) at the Weigh-in-Motion(WIM) sensor installed sections. The experimental results showed that PTCP could be acceptable for WIM sections because the displacements were negligibly smaller at the cutting location for sensor installation.

• 한국도로학회:학술대회논문집
• /
• 2003.10a
• /
• pp.303-310
• /
• 2003

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.139-146
• /
• 2010

This research was conducted to analyze the behavior of the post-tensioned concrete pavement (PTCP) system in which weigh-in-motion (WIM) sensors were installed. One lane of PTCP was constructed after removing the existing asphalt pavement. The frictional resistance between the slab and the underlying layer should be small enough for the PTCP slab to properly have prestresses by tensioning. By performing an experimental construction of PTCP, the friction effects and the longitudinal displacements of PTCP under environmental loads were investigated. Based on the knowledge obtained from the experiments, the actual PTCP sections including WIM sensors were constructed and the curling behavior of the system was investigated. As a result, the behavior of the PTCP system was not affected by the existence of WIM sensors, and the appropriate PTCP system when installing WIM sensors in it could be developed.

• 한국도로학회:학술대회논문집
• /
• 2010.03a
• /
• pp.223-228
• /
• 2010

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.123-132
• /
• 2011

The purpose of this study is to calculate and propose rational multi-lane loading factors for bridge design considering the probability of simultaneous truck passing in adjacent lanes and real truck weights. The probability of simultaneous truck passing is calculated by analyzing video image taken at various locations in highways and national roads. Weigh-In-Motion system data at two locations are used, which is combined with the probability of multiple presence to calculate the multi-lane loading factors for typical 2 lane and 5 lane bridges. Statistical properties of multi-lane loading factors are also calculated assuming that locations for video images and WIM data represent the overall traffic condition in the country. Results are compared with various design codes in the world and they show that the values are between the current Korea Bridge Design Code and AASHTO LRFD specification or Eurocode and are similar to Canadian Code.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1731-1740
• /
• 2013

The design life and durability of the bridges are strongly affected by the Gross Vehicle Weight(GVW) of heavyweight trucks. The Weigh-In-Motion(WIM) systems are typically used to collect information on truck total weight and speed. The statistical analysis of the GVW measured using High Speed WIM systems showed that most of heavy vehicles were from Vehicle Type 7, 10, and 12. The analysis was also carried out to determine goodness of fit with theoretical probability distributions. The normal distribution was shown to best describe the overall distribution of GVW. The top 10% of the GVW appeared to best fit by the Weibull 3 probability distribution.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.2
• /
• pp.147-156
• /
• 1996

In this paper we proposed a beam steering equation for the planar slotted waveguide array antenna. The tilt angle measured from the rotating axis and the aperture distribution of the antenna were the most important factors for the beam steering. From the equation, we calculated the frequency and phase distribution of the aperture for any desired beam direction. And we developed a high speed control algorithm delivering the phase data to the phase shifters of a one-dimensional phased array antenna. To reduce complexity of the control circuit and the phase delivery time, we proposed the serial phase repeating method. Because of its simplicity, we expect it can be useful for a large 2- dimensional fully phased array antenna.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.69-78
• /
• 2009

Korea has achieved significant economic growth with building the Gyeongbu Expressway. As the number of new road construction projects has decreased, it becomes more important to maintain optimal status of the current road networks. One of the best ways to accomplish it is weight enforcement as active control measure of traffic load. This study is to develop High-speed Weigh-in-motion System in order to enhance efficiency of weight enforcement, and to analyze patterns of overloaded trucks on highways through the system. Furthermore, it is to review possibilities of developing overweight control system with application of the HS-WIM system. The HS-WIM system developed by this study consists of two sets of an axle load sensor, a loop sensor and a wandering sensor on each lane. A wandering sensor detects whether a travelling vehicle is off the lane or not with the function of checking the location of tire imprint. The sensor of the WIM system has better function of classifying types of vehicles than other existing systems by detecting wheel distance and tire type such as single or dual tire. As a result, its measurement errors regarding 12 types of vehicle classification are very low, which is an advantage of the sensor. The verification tests of the system under all conditions showed that the mean measurement errors of axle weight and gross axle weight were within 15 percent and 7 percent respectively. According to the WIM rate standard of the COST-323, the WIM system of this study is ranked at B(10). It means the system is appropriate for the purpose of design, maintenance and valuation of road infrastructure. The WIM system in testing a 5-axle cargo truck, the most frequently overloaded vehicle among 12 types of vehicles, is ranked at A(5) which means the system is available to control overloaded vehicles. In this case, the measurement errors of axle load and gross axle load were within 8 percent and 5 percent respectively. Weight analysis of all types of vehicles on highways showed that the most frequently overloaded vehicles were type 5, 6, 7 and 12 among 12 vehicle types. As a result, it is necessary to use more effective overweight enforcement system for vehicles which are seriously overloaded due to their lift axles. Traffic volume data depending upon vehicle types is basic information for road design and construction, maintenance, analysis of traffic flow, road policies as well as research.