• Journal of the Korean Society of Safety
• /
• v.23 no.2
• /
• pp.81-86
• /
• 2008

Experimental studies have been performed to examine the influences of wall obstructions in a rectangular confinement. Three wall obstacles with blockage ratios ranging from 10 to 30% were used. Temporally resolved flame front images were recorded by a high-speed video camera to investigate the interaction between a propagating flame and the obstacle. The local flame displacement speed and its probability density functions(PDFs) were obtained for the wall obstructions. During the interaction with the sharp-edges of the wall obstacles, the local propagation speed increased. The increase of local speed became larger as the obstruction ratio increased. However, the averaged flame displacement speeds with different blockage ratios were not significantly different within the chamber as shown in the paper of Park et al. The flame front interaction investigated in this work was less dependent of the obstacle obstructions compared to that published in the literature for large L/D.

• Journal of the Korean Institute of Gas
• /
• v.17 no.1
• /
• pp.13-18
• /
• 2013

Experimental studies were carried out to investigate the interactions between the propagating flame fronts and different multiple obstacles within an explosion chamber. The explosion chamber is 600 mm in height, $700{\times}700mm^2$ in cross-section and has a H/L value of 0.86. Three different multiple obstacles with the blockage ratio of 0.43 were replaced within the chamber. The results showed that relatively higher local flame displacement speed was observed with the triangular obstacle while the lower was observed with the circular one. It was found that the local flame displacement speeds behind the obstacle were largely dependent on the obstacle types. It was also found that as the flame interacted with the flow field generated behind the obstacle, the probability density functions(PDFs) of the local flame displacement speed were extensively distributed toward higher speeds.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.5
• /
• pp.381-388
• /
• 2014

Our aim was to simulate ocean waves in a small-size wave flume and observe the motion of a cylindrical floating body placed in an offshore environment. To precisely visualize the oscillation of the body, a set of light-emitting diode illuminators and high-speed charge-coupled device camera were installed in the flume. Spectral analysis was performed of the movement of the floating body. The wave generator and absorbers worked well to simulate stable regular waves. As the period of the oncoming waves changed, the movement of the floating body substantially differed when tethered to a tension-leg mooring cable. In particular, when connected to the tension-leg mooring cable, the natural frequency of the floating body suddenly appeared at 0.391 Hz as the wave period was increased.

• Tunnel and Underground Space
• /
• v.25 no.1
• /
• pp.46-55
• /
• 2015

A water tube with detonating cord was devised to control the blast dust. Water diffusion experiments with different detonating cord positions were conducted during the series of experiments to optimize the design parameters of the tube. Images from high speed camera were analyzed to evaluate the results. AUTODYN program was adopted to simulate the diffusion process of water and compared with the images. Diffusion of water shows cross flow in case of external charge while the internal case shows radial flow. A bubble ring was formed during the numerical analysis of internal charge case as occurred in underwater blast. An additional bubble ring was formed by the reflection pressure from the ground. And the Weber number was determined as sufficient for spray atomization performance of the water tube.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.433-438
• /
• 2011

A machine that makes paper cups has many parts, including a barrel cam, an index, and a turret. When the barrel cam, which is the main operating part of the machine, rotates, it pushes the roller fixed on the index, and paper cups are formed as the turret connected to the index rotates. Therefore, the performance of the machine is affected by the barrel cam. In this study, the program for designing barrel cam, which creates the profile of the cam is developed using MATLAB. This profile is used to develop a 3D CAD model by using a 3D CAD program. Dynamic models containing the barrel cam are created on the basis of the profile and 3D laser scan of the barrel cam. Further, the rotation angle of the index in the machine is measured using a high-speed camera. The rotation angles of the dynamics models are compared to verify the effectiveness of the program.

• Explosives and Blasting
• /
• v.20 no.4
• /
• pp.17-28
• /
• 2002

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting, Accidents were sometimes reported due to the flying chips of fragmented materials In building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and non-woven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of apartment buildings.

• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.68-74
• /
• 2008

Measurements were performed to investigate the effects on flame and pressure development by varying locations of multiple obstacles in a top-venting explosion chamber. The chamber dimension was 1000 mm in height with a $700\;{\times}\;700\;mm^2$ cross-section and a rectangular vent area of $700\;{\times}\;700\;mm^2$. Three different multiple obstacles with blockage ratio of 30% were used by changing from 200 mm, 500 mm to 800 mm in heights within the chamber. Temporally resolved flame front images were recorded by a high speed camera to investigate the interaction between the propagating flame and the obstacles. The results showed that the triangular bar caused the fastest flame developments at given times whereas the lowest was obtained with the cylindrical bar. It was also found that local flame displacement speeds of different obstacles were sensitive to the locations of obstacles. The local speed becomes larger in going from 200 mm, to 500 mm and to 800 mm in heights. The obstacles in height of 800 mm yielded the highest overpressure whereas the lowest was in height of 200 mm.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.21 no.2
• /
• pp.133-138
• /
• 2010

Background and Objectives : High-speed imaging can be useful in studies of linguistic and artistic singing styles, and laryngeal examination of patients with voice disorders, particularly in irregular vocal fold vibrations. In this study, we introduce new laryngeal imaging systems which are commercially available high speed cameras connected with a laryngoscope. Materials and Method : The laryngeal images were captured from three different types of cameras. First, the adapter was made to connect with laryngoscope and Casio EX-F1 to capture the images using $2{\times}150$ Watt Halogen light source (EndoSTROB) at speeds of 1,200 tps (frame per second)($336{\times}96$). Second, Phantom Miro ex4 was used to capture the digital laryngeal images using Xenon Nova light source 175 Watt (STORZ) at speeds of 1,920 fps ($512{\times}384$). Finally, laryngeal images were captured using MotionXtra N-4 with 250 Watt halogen lamp (Olympus CLH-250) light source at speeds of 2,000tps ($384{\times}400$) by connecting with laryngoscope. All images were transformed into the Kymograph using KIPS (Kay's image processing Software) of Kay Pentex Inc. Results: Casio EX-F1 was too small to adjust the focus and screen size was diminished once the images were captured despite of high resolution images. High quality of color images could be obtained with Phantom Miro ex4 whereas good black and white images from Motion Xtra N-4 Despite of some limitations of illumination problems, limited recording time capacity, and time consuming procedures in Phantom Miro ex4 and Motion Xtra N-4, those portable devices provided high resolution images. Conclusion : All those high speed cameras could capture the laryngeal images by connecting with laryngoscope. High resolution images were able to be captured at the fixed position under the good lightness. Accordingly, these techniques could be applicable to observe the vocal fold vibration properties in the clinical practice.

• Journal of Korea Multimedia Society
• /
• v.9 no.5
• /
• pp.585-594
• /
• 2006

Due to the size limit, the voice coil motor (VCM) is adopted in most of the mobile phone camera to control auto-focus instead of step motor. The optical system using the VCM has the property that the focus values are varying even though the same current is induced. It means that an error of the lens position was taken placed due to the characteristics of the VCM. In this paper, a algorithm was proposed to compensate the lens position error using the step size and the search count of each stage. In the proposed algorithm -7 step middle searching stage is inserted the conventional searching algorithm for the fast auto-focus searching and the final searing step size was set to +1 for the precise focus control, respectively. In the experimental results, the focus values was found more fast in the proposed algorithm than the conventional. And more the image quality by the proposed algorithm was superior to that of the conventional.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.12
• /
• pp.2341-2347
• /
• 2016

In this paper, we implement monitoring system for grain sorting using a high-speed FPGA and embedded LINUX. The proposed system is designed by base on web server and web-based applications while existing system was designed by base on stand-alone mode.The interface the Web server with high speed hardware of FPGA is designed on the implemented monitoring system. The proposed system has the advantages of multi-tasking on Linux web server and real-time high speed on FPGA also. The control logic of a high speed rate line-scan CCD camera, the method of center of gravity, HSL decoding and the interface on the Web server are implemented in FPGA. The implemented monitoring system has the advantage of being able to control the grain monitoring, system failure and recovery remotely by web application. As a result, we can upgrade the performance of sorting quality compared by existing system.