• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.234-234
• /
• 2003

• Journal of Aerospace System Engineering
• /
• v.12 no.4
• /
• pp.106-111
• /
• 2018

Hydrodynamic ram phenomenon could be generated by external threats such as impact and blast in the aircraft. High strain rate deformation caused by the hydrodynamic ram phenomenon is one of the main factors to influence structural survivability. Mechanical properties of composite structure change rapidly under conditions of high strain rate. Therefore, it is necessary to experimentally investigate the influence of strain rates for aircraft structural survivability. In this paper, tensile tests of composite material were conducted for low and high strain rates to investigate the influence of the various strain rates. Tensile modulus increases more compared to tensile strength at high strain rate under hydrodynamic ram condition. Regression analysis was conducted to predict tensile modulus at various strain rates because it is one of the main damaging factors for composite structures under high strain rate conditions. Also, the mechanical properties of composite materials were acquired and analyzed under high strain rate conditions. It is hypothesized that the results from this study would be used for designing aircraft composite structures and evaluation considering structural survivability.

• Geotechnical Engineering
• /
• v.4 no.3
• /
• pp.27-34
• /
• 1988

Soils behave non-linearly at high strain. This study investigated the non-linear behavior of silty sands (Mixture of Ottawa Sand and Quartz Powder) by resonant column tests. The results were ·compared with Ramberg-Osgood's non-linear equation. From the tests, it was shown that the change of shear modulus and damping ratio was more sharp at low fine content, high void ratio and low confining pressure. It was also found that famberg-Osgood parameter, R was approximately 2.0, however the range of C varied from 200 to 3200.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.47-47
• /
• 2004

충격하중을 받는 재료의 거동에 관한 연구는 공학의 넓은 분야에 깊은 관계를 가지고 있다. 특히 동적하중을 받는 경계조건 하에서 사용되는 구조물을 정밀하게 설계 제작하는 필요성이 고조됨에 따라 여러 재료들의 고변형률 속도로 변형될 경우에 대한 역학적인 성질이 중요한 과제로 떠오르고 있다. 구조물의 건전성과 신뢰성을 향상시키기 위해서는 구조물이 실제적으로 받는 여러 조건의 하중하에서의 실험적으로 정밀하게 획득된 정확하고, 완벽한 재료 물성치가 필요하다. (중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.849-853
• /
• 2002

A specific experimental method, the split Hopkinson pressure bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain-rate of the order of 103/s~104/s. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from varying structures under dynamic loading are determined using a Split Hopkinson Pressure Bar technique.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.7
• /
• pp.60-68
• /
• 2004

High velocity impacts are accompanied with large deformations, which generate a large amount of heat due to plastic works, resulting in a significant temperature rise of the material. Because the elevated temperature affects the dynamic properties of materials, it is important to predict the temperature rise during high-stram-rate deformations. Both existing vacancies and excess vacancies are credited to the stored energy, yet it is difficult to distinguish one from another in contribution to the stored energy using macroscopic level materials models. In this study, an atomistic material model for fee materials such as copper is set up to calculate the stored energy using molecular dynamics (MD) simulations. It is concluded that excess vacancies play an important role for the stored energy during a high-strain-rate deformation.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.1
• /
• pp.196-204
• /
• 2003

Mechanical properties of the materials used for transportations and industrial machinery under high strain rate loading conditions such as seismic loading are required to provide appropriate safety assessment to these mechanical structures. The split Hopkinson Pressure Bar (SHPB) technique with a special experimental apparatus can be used to obtain the material behavior under high strain rate loading conditions. In this paper, dynamic deformation behaviors of the aluminum alloys such as A12024-T4, A16061-T6, and A17075-T6 under both high strain rate compressive and tensile loading conditions are determined using the SHPB technique.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1306-1313
• /
• 2004

This paper addresses a theoretical approach to calculate the amount of the stored energy during high strain-rate deformations using atomistic level simulation. The dynamic behavior of materials at high strain-rate deformation are of great interest. At high strain-rates deformations, materials generate heat due to plastic work and the temperature rise can be significant, affecting various properties of the material. It is well known that a small percent of the energy input is stored in the material, and most of input energy is converted into heat. However, microscopic analysis has not been completed without construction of a material model, which can simulate the movement of dislocations and vacancies. A major cause of the temperature rise within materials is traditionally credited to dislocations, vacancies and other defects. In this study, an atomistic material model for FCC such as copper is used to calculate the stored energy.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.158-165
• /
• 2003

A specific experimental method, the Split Hopkinson pressure bar (SHPB) technique has been widely used to determine the dynamic material properties under the impact compressive loading conditions with strain rate of the order of 10$^3$/s∼l0$^4$/s. In this paper, dynamic deformation behaviors of rubber materials widely used for the isolation of vibration from structure under varying dynamic loading are determined by using plastic SHPB technique. A transition point to scope with the dynamic deformation behavior of rubber-like material is defined in this paper and used to characterize the specifics of the dynamic deformation of rubber materials.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.107-112
• /
• 2003

Mechanical properties of the materials used for transportations and industrial machinery under high strain rate loading conditions such as high impact loading are required to provide appropriate safety assessment to varying dynamically loaded mechanical structures. The Split Hopkinson Pressure Bar(SHPB) technique with a special experimental apparatus can be used to obtain the material behavior under high strain rate loading conditions. In this paper, the dynamic deformation behavior of a brass under both high strain rate compressive loading conditions has been determined using the SHPB technique.