• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.2
• /
• pp.8-15
• /
• 2006

To reduce costs and address other practical concern related to architectural lighting, we have been involved in various aspects of advanced daylighting design and control. If we look toward future building trends, we see that the advanced has already successfully deployed such complex lighting control systems. This paper takes a broad view of what advanced manufacturers have done to develop energy efficient lighting control technologies such as sensors, lumen maintenance, time of day scheduling, peak demand reduction and so forth. First of all strategies, daylighting controls would also need to be commissioned to respond to the specific daylighting signature of the zone. To translate the daylight in term of the amount of energy savings, an electric lighting system is designed and automatic on-off control system integrated with the contribution of daylighting has been applied to the operating of the artificial lighting. The lighting analysis program, Lumen-Micro predicts the optimal layout of conventional fluorescent and incandescent lighting fixtures to meet the designed lighting level and calculates unit power density, which translates the demanded amount of lighting energy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.360-369
• /
• 2008

The solar cells should be operated at the maximum power point because its output characteristics were greatly fluctuated on the variation of insolation, temperature and load. It is necessary to install an inverter among electric power converts by means of the output power of solar cell is DC. The inverter is operated supply a sinusoidal current and voltage to the load and the interactive utility line. In this paper, the proposes a photovoltaic system is designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper is operated in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature for solar cell has typical dropping character. The single phase PWM voltage source inverter is consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be develop continuously by connecting with the source of electric power for ordinary using. It can be cause the efect of saving electric power, from 10 to 20%. The single phase PWM voltage source inverter operates in situation, that its output voltage is in same phase with the utility voltage. The inverter are supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• The KIPS Transactions:PartB
• /
• v.15B no.1
• /
• pp.37-44
• /
• 2008

With the growing proliferation of mobile computing devices, several industrial and academic research groups have a vigorous studying to remote control for various appliances with mobile devices such as Notebooks, PDAs, and Smartphones in home network environments. We can utilize the good points of mobile devices such as portability and usability so that we can remote control and manage the mobile devices connected on home networks anytime, anywhere. However, mobile devices use different languages. Therefore, they cause some problems because their interfaces and the methods of operation are different each other. To solve these problems, there are two consideration. First, we may be solved development of the user interface and difficulty of maintenance in order to control various heterogeneous devices. Second, we may provide the user interface which is dynamically adapting user's preferences and device characteristics. To satisfy these considerations, we describe the design of an adaptive user interface for home network environments using the UIML (User Interface Markup Language) based on XML (eXtensible Markup Language) and the profile information of the user and device. Therefore, we present several implementation examples that show how the framework can form the basis of prototypical applications.

• Journal of Animal Science and Technology
• /
• v.50 no.4
• /
• pp.561-572
• /
• 2008

Responses of real-time control parameters, such as ORP, DO and pH, to the conditions of biological animal wastewater treatment process were examined to evaluate the stability of real-time control using each parameter. Also an optimum index for supplemental carbon source addition based on NOx-N level was determined under a consideration of denitrification rate by endogenous respiration of microorganism and residual organic matter in liquor. Experiment was performed with lab-scale sequencing batch reactor(SBR) and working volume of the process was 45L. The distinctive nitrogen break point(NBP) on ORP-and DO-time profiles, which mean the termination of nitrification, started disappearing with the maintenance of low NH4-N loading rate. Also the NBP on ORP-and DO-time profiles was no longer observed when high NOx-N was loaded into the reactor, and the sensitivity of ORP became dull with the increase of NOx-N level. However, the distinctive NBP was constantly occurred on pH(mV)-time profile, maintaining unique profile patterns. This stable occurrence of NBP on pH(mV)-time profile was lasted even at very high NOx-N:NH4-N ratio(over 80:1) in reactor, and the specific point could be easily detected by tracking moving slope change(MSC) of the curve. Revelation of NBP on pH(mV)-time profile and recognition of the realtime control point using MSC were stable at a condition of over 300mg/L NOx-N level in reactor. The occurrence of distinctive NBP was persistent on pH(mV)-time profile even at a level of 10,000mg/L STOC(soluble total organic carbon) and the recognition of NBP was feasible by tracing MSC, but that point on ORP and DO-time profiles began to disappear with the increase of STOC level in reactor. The denitrfication rate by endogenous respiration and residual organic matter was about 0.4mg/L.hr., and it was found that 0.83 would be accepted as an index for supplemental carbon source addition when 0.1 of safety factor was applied.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.4 s.316
• /
• pp.60-69
• /
• 2007

The human eye usually experiences a loss of color sensitivity when it is subjected to high levels of luminance, and perceives a discrepancy in color between high and normal-luminance displays, generally known as a hue shift. Accordingly, this paper models the hue-shift phenomenon and proposes a hue-correction method to provide perceptual matching between high and normal-luminance displays. The value of hue-shift is determined by perceived hue matching experiments. At first the phenomenon is observed at three lightness levels, that is, the ratio of luminance is the same between high and normal-luminance display when the perceived hue matching experiments we performed. To quantify the hue-shift phenomenon for the whole hue angle, color patches with the same lightness are first created and equally spaced inside the hue angle. These patches are then displayed one-by-one on both displays with the ratio of luminance between two displays. Next, the hue value for each patch appearing on the high-luminance display is adjusted by observers until the perceived hue for the patches on both displays appears the same visually. After obtaining the hue-shift values, these values are fit piecewise to allow shifted-hue amounts to be approximately determined for arbitrary hue values of pixels in a high-luminance display and then used for correction. Essentially, input RGB values of an image is converted to CIELAB values, and then, LCh (lightness, chroma, and hue) values are calculated to obtain the hue values for all the pixels. These hue values are shifted according to the amount calculated by the functions of the hue-shift model. Finally, the corrected CIELAB values are calculated from corrected hue values, after that, output RGB values for all pixels are estimated. For evaluation, an observer's preference test was performed with hue-shift results and Almost observers conclude that the images from hue-shift model were visually matched with images on normal luminance display.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.6
• /
• pp.482-488
• /
• 2011

Seadike is a coastal structure constructed in the rear region of the foreshore to maximize its usability by preventing direct effect of wave. The expected construction field is determined under the design wave and tidal condition where minor wave overtopping is anticipated. Thus, the location of seadike is generally fixed at the highest site of the surrounding area with seadike crest height controlling the permissible range of wave overtopping volume. But a lot of times, frontal sand beach of the seadike continuously deforms due to incident waves, resulting failure in maintaining its initial slope. The erosion and deposition of the seadike front cause changes in the crest height and volume of wave overtopping and decrease in the setting depth of the seadike, which endangers seadike region as a result. In this study, the relation of local scouring and setting depth of the seadike front in the run-up region is examined by using 2D hydraulic model tests and numerical simulations by modified SBEACH model. As a result, the study learned that if appropriate boundary condition is applied to the modified SBEACH model, it is possible to create practical estimations on the local scouring at the seadike foot when erosive waves flow into the region.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.280-291
• /
• 2023

Purpose: As fire accidents happen at the production and storage sites of superabsorbent polymers for convenience of daily life, an experimental study was conducted to secure basic data to establish practical preventive measures against them. Method: The sample container (20cm width × 20cm length) was made into a rectangular cuboid with the heights of 3cm, 5cm, 7cm, and 14cm, respectively, to allow access to the infinite flat plane. The front and back of the container were covered with a 300-mesh stainless steel mesh for one-dimensional heat transfer. The sample container was placed in the center of the thermostatic bath, which was heated to a predetermined temperature by setting the thermostat program in advance, and it was determined to be 'ignited' when the central temperature of the sample rose by more than 20℃ above the set temperature, and "unignited" when it was maintained at an approximate value of the set temperature. Result: The critical autoignition temperature was calculated to be 217.5℃ when the height of the sample container was 3 cm, 212.5℃ when it was 5 cm, 202.5℃ when it was 7cm, and 187.5℃ when it was 14cm. The ignition induction time to reach the maximum temperature was 34hours for 3cm, 76hours for 5cm, 143hours for 7cm, and 318hours for 14cm. Conclusion: ① As the size of the container increased, the autoignition temperature decreased and the induction time to reach the maximum temperature increased. ② An apparent activation energy was calculated to be 44.92kcal/mol, with a correlation of 96.93%.

• Proceedings of the Korean Information Science Society Conference
• /
• 2001.10c
• /
• pp.202-204
• /
• 2001

가상 세계의 공유 개념은, 특히 사용자들이 인터넷 같이 대규모 네트웍을 통해 지역적으로 분산된 경우는 복제가 수용할 수 있는 상호작용 성능을 제공하기 때문에 각 사용자의 사이트에 정보를 복제함으로써 확장된다. 그러나, 다수의 동시 갱신은 replicas간의 일관되지 않은 뷰를 일으키게 될 것이다. 따라서, 동시성 제어가 복제자들간에 일관된 상태를 유지하도록 하기 위한 중요한 요소가 된다. 우리는 단지 대상 객체의 주변에 있는 사용자들만이 소유권 요청을 다중 전송하게 하는 확장성 있는 예측기반 동시성 제어 스킴을 제안했었다. 이 작업에서, 우리는 모든 사용자들이 동일한 속도론 가지고 가상 세계를 이동한다고 가정했다. 이것은, 그러나, 좀더 사실성을 더하기 위해 사용자가 가상 세계와 상호작용을 할 매 그들의 이동속도를 변경하도록 하는 네트웍 게임같은 네트웍 가상 환경에서는 너무 common 하다. 본 논문은 다양한 속도를 가진 사자를 지원하기 위한 확장을 제안한다. 확장된 스킴은 다른 속도의 수만큼의 다중 Entity Radii를 가지며 각 속도를 가진 사용자에게 분리된 큐를 할당한다. 각 큐는 다음 소유자 후보를 예측하기 위해 동시에 예측을 수행하고 선택된 후보들간에서 최소의 Predicted Collision Time을 가지는 최종 후보자가 선택된다. 이는 사용자의 속도에 기반을 둔 적절한 Entity Radius를 사용함으로써 소유권의 timely advanced transfer과, 다른 이돔 속도와 latency를 가지는 사용자들 간의 간섭을 줄임으로써 공정(공평)한 소유권 양도, 그리고 불필요한 소유권 전송을 줄임으로써 놓은 예측 정확도를 제공한다.성을 지닌 AMMQL 학습법은 로봇축구와 같이 끊임없이 실시간적으로 변화가 일어나는 다중 에이전트 환경에서 특히 높은 효과를 볼 수 있다. 본 논문에서는 AMMQL 학습방법의 개념을 소개하고, 로봇축구 에이전트의 동적 위치 결정을 위한 학습에 어떻게 이 학습방법을 적용할 수 있는지 세부 설계를 제시한다.다.으로서 hemicellulose구조가 polyuronic acid의 형태인 것으로 사료된다. 추출획분의 구성단당은 여러 곡물연구의 보고와 유사하게 glucose, arabinose, xylose 함량이 대체로 높게 나타났다. 점미가 수가용성분에서 goucose대비 용출함량이 고르게 나타나는 경향을 보였고 흑미는 알칼리가용분에서 glucose가 상당량(0.68%) 포함되고 있음을 보여주었고 arabinose(0.68%), xylose(0.05%)도 다른 종류에 비해서 다량 함유한 것으로 나타났다. 흑미는 총식이섬유 함량이 높고 pectic substances, hemicellulose, uronic acid 함량이 높아서 콜레스테롤 저하 등의 효과가 기대되며 고섬유식품으로서 조리 특성 연구가 필요한 것으로 사료된다.리하였다. 얻어진 소견(所見)은 다음과 같았다. 1. 모년령(母年齡), 임신회수(姙娠回數), 임신기간(姙娠其間), 출산시체중등(出産時體重等)의 제요인(諸要因)은 주산기사망(周産基死亡)에 대(對)하여 통계적(統計的)으로 유의(有意)한 영향을 미치고 있어 $25{\sim}29$세(歲)의 연령군에서, 2번째 임신과 2번째의 출산에서 그리고 만삭의 임신 기간에, 출산시체중(出産時體重) $3.50{\sim}3.99kg$사이의 아

• Korean Journal of Food Science and Technology
• /
• v.26 no.3
• /
• pp.199-203
• /
• 1994

Software for refrigerator capable of both rapid fermentation and suitable storage of Kimchi was developed and its performance was investigated. Refrigerator system consists of an insulated fermentation room, heater, damper for the control of outer cold air and two sensors for recognizing temperature of heater and fermentation room, which control temperature and time period of affecting Kimchi fermentation. Effects of fermentation at different NaCl concentration and three fermentation function keys were studied; At key I, time which was elapsed to edible ripening state, pH 4.5 and total acid 0.6%, was about $3{\sim}4$, $4{\sim}5$ and $11{\sim}12$ days, respectively. At key II, time was about $2{\sim}3$, $3{\sim}4$, and $10{\sim}11$ days, and at key III, about 2, 3 and $9{\sim}10$ days, respectively. Effect of storage at three fermentation function keys was all maintained to the level of a palatable pH range until 14 days. Sensory evaluation of Kimchi showed also significant difference in a taste.

• Journal of Energy Engineering
• /
• v.8 no.4
• /
• pp.592-604
• /
• 1999

The steady state and dynamic characteristics of large cell area MCFC stacks were analyzed to solve the problems such as temperature difference generated in stacks and pressure difference between anode and cathode. Manipulated variables (current density, duel utilization rate, oxidant utilization rate) and controlled variables (temperature difference, anode and cathode pressure difference) which had an important effect on the MCFC stack performance were determined using operation results of two types of MCFC stacks (5kW (3,000 $\textrm{cm}^2$, 20 ea). 3kW (6,000 $\textrm{cm}^2$, 5ea)). The stability and transfer function representing system dynamics were obtained by steady state gain rate which showed the relative change between MVs and CVs. The transfer function was a 3$\times$3 matrix and a typical first order system without time delay. The optimal operating condition of large cell area MCFC stacks could be determined by analyzing dynamic characteristics. In case of a 5 kW MCFC stack, pressurized operation with recycle flow should be used to control the outlet temperature less than 68$0^{\circ}C$ and to control the MCFC system effectively. MIMO control or decoupler should be used to remove the interaction between MVs and CVs. This result will be used as important data in determining the control structure design and operation mode of large cell area MCFC systems in the future.