• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.752-755
• /
• 2011

이종재료의 열전달문제 수치해석시 추가적으로 만족시켜야 하는 계면경계조건들의 존재와 계면경계로 인한 불연속면의 처리는 근사함수의 구성 뿐만 아니라 수치기법의 개발 자체를 어렵게 만든다. 본 논문에서는 계면경계의 불연속성을 모델링하는 특수한 함수를 포함하고 계면경계조건을 항상 만족시킬 수 있는 근사함수를 구성하고, 계면경계문제의 강형식을 직접 이산화하며 고속으로 해를 계산할 수 있는 이동최소제곱 차분법을 제시한다. 계면경계조건이 매입된 이동최소제곱 차분법으로 이종재료의 열전달문제를 해석한 결과, 높은 정확성과 효율성을 갖는 것을 확인할 수 있었다.

• Composites Research
• /
• v.16 no.2
• /
• pp.18-25
• /
• 2003

The tensile properties of short nylon6 fiber reinforced NR and SBR have been investigated as functions of fiber aspect ratio(AR), diameter ratio(DR), interphase condition, and fiber content. The tensile strength increased with increasing fiber AR(20 min.) and good interphase conditions. The short-fiber(DR=3 and AR=20 min.) reinforced SBR did not show the dilution effect for all interrhase conditions. And the short-fiber(DR=3 and AR=20min.) reinforced NR did not show the dilution effect except for the no-coating. The tensile moduli were significantly improved due to fiber AR. fiber content, and good interphase at same DR. The better interphase condition showed the higher pull-out force at same DR. Also, the stress analysis near the fiber end carried out using axisymmetric FEA to be convinced of the reinforcing mechanism. It is found that the fiber AR, interphase and DR have an important effect on tensile properties.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.55-58
• /
• 2009

본 논문에서는 독립적으로 구성된 유한요소 모델을 결합하기 위하여 계면에서 불일치 격자들을 처리하는 기법을 소개하고자 한다. 불일치 격자들로 인하여 요소들의 침투와 틈이 발생할 수 있고 일반적인 유한요소를 사용하면 계면에서 변위의 연속성과 하중전달 조건들을 만족시키기가 불가능하게 되는데 계면에서 정의된 계면요소를 사용하여 결합을 위한 조건들을 만족시킬 수 있게 된다. 요소들의 침투와 틈이 없는 연속적인 계면을 정의하고 여기에 부합하는 계면요소를 구성하며 유한요소 형상함수와 다른 계면요소 형상 함수를 사용하게 되면 독립적으로 구성된 분리 영역들을 자연스럽게 결합할 수 있게 된다. 계면요소는 연속성, 적합성, 완전성 등에서 유한요소와 유사한 특성을 갖으며 추가적인 자유도 없이 불일치 격자를 결합하게 된다. 계면요소법을 사용하여 분리된 영역의 결합이나 전체-국부 해석 그리고 유체-구조물 상호작용해석 등에 적용되어 유용한 방법으로 사용될 수 있게 된다.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.49-55
• /
• 2016

The effects of post-annealing and temperature/humidity conditions on the interfacial adhesion energies of atomic layer deposited RuAlO diffusion barrier layer for Cu interconnects were systematically investigated. The initial interfacial adhesion energy measured by four-point bending test was $7.60J/m^2$. The interfacial adhesion energy decreased to $5.65J/m^2$ after 500 hrs at $85^{\circ}C$/85% T/H condition, while it increased to $24.05J/m^2$ after annealing at $200^{\circ}C$ for 500 hrs. The X-ray photoemission spectroscopy (XPS) analysis showed that delaminated interface was RuAlO/$SiO_2$ for as-bonded and T/H conditions, while it was Cu/RuAlO for post-annealing condition. XPS O1s peak separation results revealed that the effective generation of strong Al-O-Si bonds between $AlO_x$ and $SiO_2$ interface at optimum post-annealing conditions is responsible for enhanced interfacial adhesion energies between RuAlO/$SiO_2$ interface, which would lead to good electrical and mechanical reliabilities of atomic layer deposited RuAlO diffusion barrier for advanced Cu interconnects.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.712-715
• /
• 2009

본 연구에서는 고밀도, 고촉진 가스하이드레이트 생성 촉진제 (promoter)의 개발을 위하여 음이온성 멀티체인형 게면활성제를 제조하였다. 또한 각 계면활성제의 알킬그룹의 길이에 따라 같은 조건에서의 계면활성제의 촉진 효과를 비교하였다. $1^{\circ}C$에서 35bar,40bar로 압력을 달리하여 비교 실험하여 메탄 하이드레이트 생성속도를 측정하고, 각 조건에서의 계면활성제의 촉진 효과를 비교하였다. 알킬그룹의 길이가 짧을수록, 압력이 높을수록 촉진 속도가 빠르다. 또한 기존의 상용화된 SDS(Sodium dodecyl sulfate)보다 본 연구에서 제조한 C10의 음이온성 멀티체인형 계면활성제가 SDS 대비하여 소량으로도 충분한 효과를 나타냄을 확인하였다.

• Composites Research
• /
• v.13 no.3
• /
• pp.30-37
• /
• 2000

The dynamic properties of short-fiber reinforced Chloroprene rubber have been studied as functions of interphase conditions and fiber content. The loss factor generally decreased with fiber content and showed different patterns according to interphase conditions. The better interphase condition showed the lower loss modulus, $E_2$. Also, the dynamic ratio decreased with fiber content and rapidly decreased in the case of double coatings, i.e., model C. Therefore, the short-fiber reinforced rubber could have the better isolation in frequency ratio($\sqrt{2}$ min.) compared to frequency ratio($\sqrt{2}$ max.). And we have investigate the possibility of applying short-fiber reinforced rubber to automotive engine mount.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.4
• /
• pp.215-222
• /
• 2019

The heat conduction problem with discontinuous material coefficients generally consists of the conservative equation, boundary condition, and interface condition, which should be additionally satisfied in the solution procedure. This feature often makes the development of new numerical schemes difficult as it induces a layered singularity in the solution fields; thus, a special approximation is required to capture the singular behavior. In addition to the approximation, the construction of a total system of equations is challenging. In this study, a wedge function is devised for enriching the approximation, and the interface condition itself is embedded in the moving least squares(MLS) derivative approximation to consistently satisfy the interface condition. The heat conduction problem is then discretized in a strong form using the developed derivative approximation, which is named as the interface immersed MLS difference method. This method is able to efficiently provide a numerical solution for such interface problems avoiding both numerical quadrature as well as extra difference equations related to the interface condition enforcement. Numerical experiments proved that the developed numerical method was highly accurate and computationally efficient at solving the heat conduction problem with interfacial jump as well as the problem with a geometrically induced interfacial singularity.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.123-127
• /
• 2003

액상실리콘으로 이루어진 초고압전력케이블용 프리몰드 접속재의 반도전-절연체 계면접합체를 다양한 제조조건과 조합별로 제조하여 계면접착력에 대한 영향을 검토하였다. 후가교적용 시 계면접착력이 강화되며 grade조합에 따른 특성차이가 존재하였다. 하지만 고온 장시간의 후가교 조건에서는 계면간의 화학적 결합력의 저하로 인해 오히려 접착력이 낮아지기도 하였다. 절연 RTV와의 계면접착성은 S-1재료가, 절연 LSR의 경우에는 S-3 재료가 가장 우수하였으며 도전안정성 측면에서도 S-3 재료가 상대적으로 유리하였다. 매입형 전극체를 제조하여 절연파괴거동을 연구한 결과 계면접착성과의 직접적인 상관관계는 크지 않음을 알 수 있었다.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.2
• /
• pp.23-30
• /
• 2001

Column tests were carried out to examine the effect of surfactant solution conditions on the surfactant-enhanced remediation of soil columns contaminated by toluene. The conditioned parameters of the surfactant solution for the column tests were concentration, pH, temperature and flow rate. The test results revealed that an optimum condition was achieved for 4% (v/v) of concentration, 10 of pH, $20^{\circ}C$ of temperature and 4 mL/min of flow rate respectively. The removal of 95% of toluene was obtained when optimal conditions of each surfactant solution parameter were simultaneously met. This was a marked improvement and removal efficiency increased by 6-19% compared to that with unadjusted conditions. The optimum range of these parameters may be useful for a surfactant-based remediation in the aquifer contaminated by toluene.

• Economic and Environmental Geology
• /
• v.35 no.2
• /
• pp.149-154
• /
• 2002

Column tests were carried out to examine the effect of surfactant solution conditions on surfactant-enhanced remediation of contaminated soil. The selected conditions of the surfactant solution were concentration and pH. 1,2,4-trichlo-robenzene (TCB) was chosen as the model hydrophobic organic substances. Sodium diphenyl oxide disulfonate (DOSL) and octylphenoxypoly ethoxyethanol (OPEE) surfactants were selected for this study. Two Iowa soils, Fruitfield sand and Webster clay loam, were leached with surfactant solution. The test results revealed that an optimum condition was achieved for 4 %(v/v) of concentration and 10 of pH, respectively. The maximum recoveries of added TCB (93-98%) were obtained when optimal conditions of each surfactant solution parameter were simultaneously met. The optimum conditions of these parameters may be useful for surfactant-assisted remediation in soil contaminated by TCB.