• Food Science of Animal Resources
• /
• v.23 no.1
• /
• pp.28-31
• /
• 2003

The incidence of PSE pork by lairage time, use of electric probe, stunning voltage condition and carcass chilling rate was compared. The incidence of PSE pork was 22.2% when pigs were held in lairage overnight without electric probe, whereas it was 59.3% when held in lairage for < 1.5 hr with electric probe before slaughter. The incidence of PSE pork was 42.37% when pigs were treated with 230 V of stunning condition, and was 66.67% when treated with 500V of stunning condition. The incidence of PSE pork was 52.2% when the ultimate carcass internal temperature was controlled higher than 38$^{\circ}C$ with the slow chilling(-5$^{\circ}C$ for 70 min), and was 39.6% when controlled lower than 30$^{\circ}C$ with the fast chilling(-15$^{\circ}C$ for 70 min). Results indicated that the incidence of PSE pork was decreased by 37.1% with lairage overnight and without use of electric probe, 24.3% with low voltage stunning treatment and 12.6% with fast chilling. However, the incidence of PSE pork was not significantly correlated with carcass weight.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.44-48
• /
• 2011

본 연구에서는 구조물 상치에 에어챔버를 설치하여 챔버 내부의 공기주입량에 따라 흘수심을 조절 할 수 있는 유공 및 투수성부유식방파제를 사용하였으며, 부유식방파제의 흘수심구간에 유공을 두어 내부의 흐름에 따른 에너지소산 효과를 수리모형실험을 통하여 분석하였다. 기존 연구에 의하여 선행되어진 부유식방파제의 형상은 구조물 제체의 입사면과 투과면이 막힌 형태의 연구가 대다수였으나, 계류라인의 장력에 따른 부체의 안정성을 고려하여 본 수리모형실험에서는 입사면 흘수심구간과 투과면 흘수심구간에 유공 및 투수층을 두어 진행하는 입사파랑을 일부 흡수하도록 하였다. 또한, 부유식방파제 흘수심단면의 내부에서 흐름변화에 의한 에너지소산 효과와 입사면과 투과면의 유공률 변화에 따른 방파성능을 무공 부유식방파제와 비교하며 효율성을 분석하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.5
• /
• pp.479-487
• /
• 2023

Recently, the destructive power of typhoons is continuously increasing owing to global warming. In a situation where the installation of floating wind turbines is increasing worldwide, concerns about the huge loss and collapse of floating offshore wind turbines owing to strong typhoons are deepening. A new type of disconnectable mooring system must be developed for the safe operation of floating offshore wind turbines. A new submersible mooring pulley considered in this study is devised to more easily attach or detach the floating of shore wind turbine with mooring lines compared with other disconnectable mooring apparatuses. To investigate the structural safety of the initial design of submersible mooring pulley that can be applied to an 8MW-class floating type offshore wind turbine, scale-down structural models were developed using a 3-D printer and structural tests were performed on the models. For the structural tests of the scale-down models, tensile specimens of acrylonitrile butadiene styrene material that was used in the 3-D printing were prepared, and the material properties were evaluated by conducting the tensile tests. The finite element analysis (FEA) of submersible mooring pulley was performed by applying the material properties obtained from the tensile tests and the same load and boundary conditions as in the scale-down model structural tests. Through the FEA, the structural weak parts on the submersible mooring pulley were reviewed. The structural model tests were conducted considering the main load conditions of submersible mooring pulley, and the FEA and test results were compared for the locations that exceeded the maximum tensile stress of the material. The results of the FEA and structural model tests indicated that the connection structure of the body and the wheel was weak in operating conditions and that of the body and the chain stopper was weak in mooring conditions. The results of this study enabled to experimentally verify the structural safety of the initial design of submersible mooring pulley. The study results can be usefully used to improve the structural strength of submersible mooring pulley in a detailed design stage.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.5
• /
• pp.215-226
• /
• 2018

In this paper, to estimate the dynamic behavior of a submerged floating tunnel(SFT) by underwater explosion(UE), the SFT is modeled and analyzed by the explicit structural analysis package LS-DYNA. The section of SFT near to explosion point is modeled to shell and solid elements using elasto-plasticity material model for concrete tubular section and steel lining. And the other parts of the SFT are modeled to elastic beam elements. Also, mooring lines are modeled as tension-only cable elements. Total mass of SFT is including an added mass by hydrodynamic effect. The buoyancy on the SFT is considered in its initial condition using a dynamic relaxation method. The accuracy and the feasibility of the analysis model aree verified by the results of series of free field analysis for UE. And buoyancy ratio(B/W) of SFT, the distance between SFT and an explosion point and the arrangement of mooring line aree considered as main parameters of the explosion analysis. As results of the explosion analysis, the dynamic responses such as the dent deformation by the shock pressure are responded less as more distance between SFT and an explosion point. However, the mooring angle of the diagonal mooring system can not affect the responses such as the horizontal displacement of SFT by the shock pressure.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.813-820
• /
• 2010

The spread mooring system for FPSO is developed to explore deep sea area, in which swell is dominant. It is known that the tension response of mooring lines in this sea area shows bimodal spectrum. Assuming normal distribution of tension profile and Rayleigh distribution of tension amplitude, the power spectral density function (PSD) of the mooring tension under the bimodal stationary random process is applied for the calculation of spectrum fatigue. Three popular methods, which are simple summation method, combined spectrum method and Jioa-Moan method, are used to combine fatigue damages from bimodal spectrum characteristics. Each damage value is compared with damage using Rainflow Cycle Counting (RCC) method which is believed to be close to exact solution. Vanmarcke' parameter and RMS(Root Mean Square) ratio are employed to assess relative damage variations between from RCC method and from three combination methods. Finally the most reliable fatigue damage combining method for spread mooring system is suggested.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.1
• /
• pp.40-53
• /
• 1996

In this paper, the wave drift damping is studied. An approximate method is adopted to calculate the wave drift damping for the sake of practical applications. By assuming the ship's forward speed to be low, the Green function and the velocity potential are expanded asymptotically with respect to the Brard number(${\tau}$) and terms up to the first order of ${\tau}$ are retained. Mean wave drift forces are computed straightforwardly. The wave drift damping is estimated as the change rate of the mean wave drift force with respect to the ship's speed. In order to validate the present method, Series 60(Cb=0.7) ship is exemplified for forward speed of Fn=0, 0.02 and 0.04. To predict the wave drift damping experimentally, three geosym models of the Esso-Osaka tanker are used. Also the effect of drift angle on the wave drift damping is also considered. Comparisons between numerical and experimental results show reasonable agreements.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.1
• /
• pp.45-54
• /
• 2008

"Summer Deadweight Tonnage(SDWT)" is used as the criteria of the berthing capacity when establishing port entry limits under current guideline. The important factors affecting to the maximum ship size of possible berthing are mass, length and breath of the ship rather than deadweight. Therefore this guideline should be modified to ensure safety and efficient operation of berth. This study aimed to propose a rational guideline to adjust the berthing capacity. In order to decide proper berthing capacity, three berths of Port of Ulsan were selected and systematic evaluations for the safety of passage transit, berthing maneuvers, ship motions at berth and stabilities of structures were conducted. Small changes of ship size had little effect on those characteristics and little significant differences were found according to the increase of ship size at the same displacement. The evaluation results of the increasement of 50% of berthing capacity at 20,000 DWT, 25% at 40,000 DWT and 13% at 150,000 DWT were within the design criteria in which the berths were built. Therefore, if the channel width, diameter of turning circle, berth length and mooring arrangements are satisfied with the criteria, the current berth limitations should be adjusted by the displacement. as substitute for the deadweight.

• Journal of Navigation and Port Research
• /
• v.46 no.6
• /
• pp.491-500
• /
• 2022

It has been noted that an accurate estimation of wind loads on offshore structures such as an FLNG (Liquefied Natural Gas Floating P roduction Storage Offloading Units, LNG FPSOs) with a large topside plays an important role in the safety design of hull and mooring system. Therefore, the present study aims to develop a computational model for estimating the wind load acting on an FLNG. In particular, it is the sequel to the previous research by the author. The numerical computation model in the present study was modified based on the previous research. Numerical analysis for estimating wind loads was performed in two conditions for an interval of wind direction (α), 15° over the range of 0° to 360°. One condition is uniform wind speed and the other is the NPD model reflecting the wind speed profile. At first, the effect of sand-grain roughness on the speed profile of the NPD model was studied. Based on the developed NPD model, mesh convergence tests were carried out for 3 wind headings, i.e. head, quartering, and beam. Finally, wind loads on 6-degrees of freedom were numerically estimated and compared by two boundary conditions, uniform speed, and the NPD model. In the present study, a commercial RANS-based viscous solver, STAR-CCM+ (ver. 17.02) was adopted. In summary, wind loads in surge and yaw from the wind speed profile boundary condition were increased by 20.35% and 34.27% at most. Particularly, the interval mean of sway (45° < α <135°, 225° < α < 315°) and roll (60° < α < 135°, 225° < α < 270°) increased by 15.60% and 10.89% against the uniform wind speed (10m/s) boundary condition.

• Journal of Korean Society of Archives and Records Management
• /
• v.6 no.2
• /
• pp.157-184
• /
• 2006

Presidential records which have produced during a presidency as a national center are the evidence of the presidency and main historical records. We have the responsibility to establish fundamental systems to produce such main historical records and to manage such main historical records which could help people and history to judge the presidency based upon the evidence of their activities. The historical appraisal could be achieved not by memory but by evidence. A draft of a proposed law on the management of presidential records which includes the establishment of presidential libraries for the presidential records Mecca is being moored at the National Assembly now. The presidential library is to be considered as a multi-functional national institution which is carrying out the role as an Archives, Museums and Center for the education. In addition, it is imperative for a presidential library to provide user-oriented services to enrich the usability and the value of records, recognizing the change of administration paradigm from a supplier-oriented system to a customer-oriented system. This dissertation, in order to develop presidential library service programs focusing on customers rather than the convenience of administration, reviewed programs of the U.S. presidential libraries as a developed case and proposes guidelines and applicable samples for the development of the Korean presidential library service programs.

• Journal of Animal Environmental Science
• /
• v.15 no.3
• /
• pp.251-262
• /
• 2009

In this research dairy cattle barn facilities what are 4,198 houses hold over 50 heads were surveyed by scale and province. Full-time farms hold over 50 heads breed total 344,514 heads. Each of Farms holds 50 to 99 heads were 79.8 percent and breed average 82.1 heads. Dairy cattle barns were constructed september 1995 averagely. Each of barns have $1,740.0\;m^2$ scale. The construction type of dairy cattle barn was almost litter barn type 84.0%, freestyle type 5.1%, mooring+litter ground type 17.3% and other types 4.4%. The litter barn type was popular in small farms. But in large farms, freestyle type was popular than small farms. The construction type of dairy cattle barn was almost litter barn type 84.0%, freestyle type 5.1%, moohng+ltter ground type 17.3% and other types 4.4%. Type of dairy cattle robotic milking system was pipeline 41.5%, herringbone 22.8% and tandem 35.8%. The pipeline type was popular in small farms which have 50~99 heads. But in large farms which have over 200 heads, tandem type was popular than small farms. Proportion of floor type of dairy cattle barn was almost litter type 94.9%. Scraper type was popular in large farms than in small farms. Proportion of roof type of dairy cattle barn was slate 32.5%, vinyl 16.3%, sunlight 11.1%, panel 10.9, zinc plate 8.8 and steel plate 8.3%. Roof type was lots of slate type before 1995. But vinyl type is increasing after 1995. Proportion of wall type of dairy cattle barn was almost open type 83.3% and winch-curtain 26.8%. Utilization period of dairy cattle barn was 9.2 years about milker, 7.9 years about automatic feeder, 9.2 years about waterer and 10.4 years about electric facilities. In this results, there were lots of improvements about automatic feeder.