• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.184-184
• /
• 2011

선로의 레일은 재료적인 특성과 현장의 많은 주변 요소에 의한 불확실성이 매우 높은 시스템으로 결함의 위험이 상존한다. 결함 발생과 조치에 따라 영업손실로 이어지므로 레일 결함 발생과 동시에 적절한 조치가 요구된다. 따라서 레일결함 발생 시 레일교환시기를 파악하는 것이 선로관리비용을 줄일 수 있으며 레일교환에 대한 신속한 판단을 위함 관리기준을 정립하는 것이 요구된다. 현재 국내에서 고속선의 경우 관리 기준이 있으나, 일반철도는 없는 실정이다. 본 연구는 차후 일반철도 180km/h 속도상승을 계획하고 있는 현 시점에 국외 관리기준을 분석하여 결함관리기준을 정립에 기여하고자 한다. 국내의 경우, 2004. 4. 1 프랑스 기술을 전수받아 개통한 고속선은 프랑스 레일관리기준을 적용한 "레일손상 등급별 관리기준"을 제정하여 레일관리를 시행하고 있다. 국외의 경우, INNOTRACK프로젝트 안에서 관련된 다른 IM(Infrastructure Managers, 사회기반시설 관리자들)에게 최근의 활동과 변화의 이해를 제공하기 위해서, 선택된 결함들의 최소조치들의 조사가 Network Rail, OBB, Prorail, Banverket 그리고 DB에서 수행되고 있으며 UIC 지침에도 포함되고 있다. 모든 최소조치 원칙은 초음파나 육안에 의해 발견된 길이나 초음파 또는 와류탐상기(eddy current system)를 이용한 깊이에 대한 제한(limits)을 준다. 또한 침목과 이음매 또는 용접부에 관한 위치에 관한 결함의 제한이 있다. 명시된 기간은 즉각적일 수도 있으며, 보통 속도 제한이나 비상 죔쇠(Clamps)같은 경감시키는 수단에 적용될 수 있으며, 또는 더 긴 기간이 될 수도 있다. 더 긴 기간들은 수리나 레일 교체를 통하여 선로로부터 결함이 제거되어야 하는 최대의 시간이다. 본 연구에서는 Transverse Breaks, Squats, Head Checks 3가지 결함 유형에 대해 각 국에서 사용하는 최소 조치를 비교하여 분석하였다. 분석결과, 유럽에서는 레일결함에 대하여 깊이 있는 연구를 통하여 관리기준을 정하여 관리하고 있으며 이에 따라 상세하고 구체적인 레일 관리가 가능하므로 효율적이며 안전성이 제고되는 것으로 판단된다. 차후 일반철도의 180km/h 속도상승을 계획하고 있는 현 시점에서 국내철도 일반선 여건에 적합한 레일결함관리기준을 정립하기 위한 추가적인 연구가 필요할 것으로 판단된다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.3
• /
• pp.45-50
• /
• 1998

This paper presents experimental results on the application of very low frequency(VLF) voltage to replace conventional DC test as an after laying test for underground distribution cables. We carried out several tests to prove defects detecting ability of VLF test on the 5m length real cables having knife-cut or needle type defects which is made in our La.. Through this experiment we proved it is very difficult to initiate electrical tree from the defects inside of the cable insulation but once the electrical tree is initiated it grows very fast and VLF does not make new defects and expand the defect. Therefore VLF test equipment for quality inspection test of manufacture is more effective than field application for underground distribution cables.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.4
• /
• pp.231-238
• /
• 2006

Nondestructive examination for low pressure turbine disc in standard nuclear power plant using phased array technique was studied. For this purpose, disc mockups were made and notches were machined in the mockups. Detection and length sizing by different methods are compared. Depth of deep notches could be measured by using AATT(absolute arrival time technique) or RATT(relative arrival time technique) but shallow notches that must be detected in early stage couldn't be measured by these two methods. For this case, notch depth was estimated by using signal response angle range and preyed usefulness.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.3
• /
• pp.275-281
• /
• 2004

Socket weldment used to change the flow direction of fluid nay have flaws such as lack of fusion and cracks. Liquid penetrant testing or Radiography testing have been applied as NDT methods for flaw detection of the socket weldment. But it is difficult to detect the flaw inside of the socket weldment with these methods. In order to inspect the flaws inside the socket weldment, a ultrasonic testing method is established and a ultrasonic transducer and automated ultrasonic testing system are developed for the inspection. The automated ultrasonic testing system is based on the portable personal computer and operated by the program based Windows 98 or 2000. The system has a pulser/receiver, 100MHz high speed A/D board, and basic functions of ultrasonic flaw detector using the program. For the automated testing, motion controller board of ISA interface type is developed to control the 4-axis scanner and a real time iC-scan image of the automated testing is displayed on the monitor. A flaws with the size of less than 1mm in depth are evaluated smaller than its actual site in the testing, but the flaws larger than 1mm appear larger than its actual size on the contrary. This tendency is shown to be increasing as the flaw size increases. h reliable and objective testing results are obtained with the developed system, so that it is expected that it can contribute to safety management and detection of repair position of pipe lines of nuclear power plants and chemical plants.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.1
• /
• pp.38-44
• /
• 2003

Performance demonstration with real flawed specimens has been strongly required for nondestructive evaluation of safety class components in nuclear power plant. Mechanical or thermal fatigue crack and intergranular stress corrosion cracking could be occured in the in-service nuclear power plant and mechanical fatigue crack was selected to study in this paper. Specimen was designed to produce mechanical fatigue flaw under tensile stress. The number of cycles and the level of stress were controlled to obtain the desired flaw roughness. After the accurate physical measurement of the flaw size and location, fracture surface was seal-welded in place to ensure the designed location and site. The remaining weld groove was then filled by using gas-tungsten are welding(GTAW) and flux-cored arc welding(FCAW). Results of radio graphic and ultrasonic testing showed that fatigue cracks were consistent with the designed size and location in the final specimens.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.11a
• /
• pp.153-156
• /
• 2003

본 논문에서는 첫 행과 마지막 행에 추가 링크를 갖는 $m{\times}n$ 메쉬 연결망 $M_{2}(m,\;n)$의 고장 해밀톤 성질을 고려한다. 이분 그래프인 $M_{2}(m,\;n)$에 하나의 결함 링크가 발생하더라도 임의의 두 노드가 다른(같은) 집합에 속한 경우 두 노드를 잇는 길이 mn - 1(mn - 2)인 경로가 존재함을 보인다. 또한 하나의 결함 노드 또는 링크가 있는 경우 임의의 두 노드를 잇는 적어도 길이 mn - 4인 경로가 존재함을 보인다. 이러한 결과들을 이용하여 짝수개의 노드를 갖는 3차원 메쉬의 고장 해밀톤 성질을 보인다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.4
• /
• pp.313-320
• /
• 1998

To record and evaluate the flaws which were found during pre-service/in-service inspection performance of nuclear power plants in Korea, the center line beam method described in ASME code and 6 dB drop method stated in CSA code were used. The measured through wall dimensions and lengths by these methods were compared and analyzed in this report. With the measured data analysis, the ekact understanding and use of these methods improves the reliability of flaw sizing and assures the integrity of nuclear power plant components.

• The Science & Technology
• /
• v.32 no.6 s.361
• /
• pp.16-17
• /
• 1999

유전자치료시대의 막이 오르면 태아의 결함이 바로잡는 것은 물론 태어날 아기에게 장수와 높은 지능지수(IQ) 그리고 미모와 좋은 성격까지 얹어줄 수 있는 길이 열릴지 모른다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.1
• /
• pp.73-82
• /
• 1983

초기결함을 가진 직교이방성원통셸이 축방향스텝하중을 받은 때의 동적좌굴을 연구하였다. 원통 쉘의 운동방정식은 비선형 Donnell 방정식을 사용하였으며 변위식에는 6개항을 채용하였다. 좌굴 조건은 원통셸의 수직변위와 길이변화의 급격한 변화로써 정의하였다. 좌굴모우드형상은 초기결 함과 쉘재료의 이방성에 따라 달라짐은 발견하였고 좌굴강도는 초기결함의 증가에 따라 크게 감 소된다.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.25-32
• /
• 2001

A microwave vacuum (MW/V) dryer was developed for drying short roundwoods, from which woodcraft souvenirs in Korean market are mostly made, and which were hardly dried without defects in a conventional kiln. It consisted of three 1.5 kW magnetrons of 2,450 MHz, a vacuum pump, a load cell of 100 kg and a cavity of $580{\times}580{\times}1,360\;mm^3$. A computer program was developed to switch on or off the magnetrons according to drying schedules, those were based on microwave injection time or the average of wood temperatures. To evaluate the new MW/V dryer the roundwood specimens of rigida pine, poplar and birch were dried. Their log diameters and lengths ranged from 125 to 25 em and from 25 to 50 cm, respectively. In spite of the presence of minor drying defects, the MW/V drying is found to be an effective method for drying short roundwoods. Wooden turneries made of red alder and ash logs were also MW/V dried from green to 4%MC without any degradation. The rates of the MW/V drying were examined for three different lengths of poplar logs.