• Composites Research
• /
• v.13 no.1
• /
• pp.61-68
• /
• 2000

A new approach is presented for the analysis of transient waves propagating in anisotropic composite laminates. The wavelet transform (WT) using the Gabor wavelet is applied to the time-frequency analysis of dispersive flexural waves. It is shown that the peaks of the magnitude of WT in time-frequency domain is related to the arrival times of group velocity. Experiments are performed using a lead break as the simulated fracture source on the surface of quasi-isotropic and unidirectional laminates. For predictions of the dispersion of the flexural mode, Mindlin plate theory is shown to give good agreement with the experimental results. Based on the frequency-dependent arrival times and angular dependence of group velocities of flexural waves, the problem of source location in anisotropic laminates is considered and the results are given.

• Tunnel and Underground Space
• /
• v.20 no.3
• /
• pp.153-168
• /
• 2010

A fifth equation is required to determine the five independent elastic constants of a transversely isotropic rock from compression test of a single specimen. As an approximation proposed by Saint-Venant has been used for long time, it may cause an erroneous result in some cases, especially for specimen with low angle of anisotropy. Three equations were suggested replacing this traditional equation and proved to be applicable by the model analysis in the previous studies. As Saint-Venant's approximation is turned out the same as the first one of them, it has the characteristics that the apparent Young's modulus is monotonously increasing according to the anisotropic angle. The methodology to analyze the elastic constants from four independent strain measurements by uniaxial compressive test of a single standard specimen is concisely described, and the necessity and compatibility of new suggested equations are discussed. Saint-Venant's approximation can determine the elastic constants close to true values and other equations may be unnecessary in specimens with medium to large angle. Nevertheless, they may become applicable because they can produce the almost same amount. For the specimens of small angle of anisotropy, Saint-Venant's approximation may result in out of general ranges or thermodynamic constraints, but other suggested equations can produce the almost true value. Thus they can be applied before other alternative equation is known. The guide map constructed by model study may decide the most compatible one of the three equations.

• Korean Journal of Optics and Photonics
• /
• v.24 no.5
• /
• pp.271-278
• /
• 2013

The effective reflection coefficients of an obliquely incident wave on a multi-layered substrate coated with a uniaxially anisotropic alignment layer are derived. The effective reflection coefficients as well as explicit ellipsometric expressions are provided as a function of film constants of multiple layers together with magnitude of anisotropy, direction of optic axis, and thickness of the alignment layer. It is expected that by adapting these expressions to the conventional modelling technique, the ordinary refractive index, the extra-ordinary refractive index, the azimuth angle and the tilt angle of the optic axis, and the thickness of the aligned surface can be determined simultaneously together with the thickness and volume fraction of each layer beneath the alignment layer.

• Journal of the Korean Magnetics Society
• /
• v.5 no.4
• /
• pp.324-334
• /
• 1995

앞의 논문에서 살펴 본바와 같이 밀도 범함수 이론에 바탕을 둔 제일 원리적 에너지 띠 계산 방법의 하나인 FLAPW(Full-potential Linearized Augmented Plane Wave) 방법 에 의해 표면, 계면, 초격자에서의 전자 구조및 자기적 성질, 그리고 구조적 성질이 잘 설명될수 있음을 보았다. 이러한 성공적 결과에도 불구하고 전자구조 계산 방법은 풀어야할 새로운 문제에 직면하고 있는데 그 중 중요한 것은 스핀-궤도 결합(spin-orbit coupling : SOC)을 어떻게 취급하며, 그 결과로 나타나는 자기 결정 이방성( magnetocrystallinge anisotropy : MCA)과 강자성 금속에서 나타나는 광자기적 효과를 설명하는 것이다.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.21-36
• /
• 2005

Although the main geology of Korea consists of granite and gneiss, it Is not uncommon to encounter anisotropy Phenomena in crosshole radar tomography even when the basement is crystalline rock. To solve the anisotropy Problem, we have developed and continuously upgraded an anisotropic inversion algorithm assuming a heterogeneous elliptic anisotropy to reconstruct three kinds of tomograms: tomograms of maximum and minimum velocities, and of the direction of the symmetry axis. In this paper, we discuss the developed algorithm and introduce some case histories on the application of anisotropic radar tomography in Korea. The first two case histories were conducted for the construction of infrastructure, and their main objective was to locate cavities in limestone. The last two were performed In a granite and gneiss area. The anisotropy in the granite area was caused by fine fissures aligned in the same direction, while that in the gneiss and limestone area by the alignment of the constituent minerals. Through these case histories we showed that the anisotropic characteristic itself gives us additional important information for understanding the internal status of basement rock. In particular, the anisotropy ratio defined by the normalized difference between maximum and minimum velocities as well as the direction of maximum velocity are helpful to interpret the borehole radar tomogram.

• The Korean Journal of Rheology
• /
• v.4 no.1
• /
• pp.52-61
• /
• 1992

초고분자량 폴리에틸렌을 파라 크실렌에 녹인 희박 용액에 전단흐름을 가해 섬유를 뽑아내는 방법에 대해 연구하였다. 표면성장이라 불리는 이 방법을 용액내에서 회전하는 rotor 의 표면에 흡착된 젤 층에, 결정성이 강한씨(seed)를 접촉시킴으로써 엉킨 분자쇄들이 전단력에 의해 신장되어 분자의 자유에너지가 증가하도록 하여 연속적으로 고강력, 고탄성 률 결정을 뽑아내게 한 것이다. 이표면성장법으로 섬유를 얻는데 있어서 결정화온도 rotor 속도, 권취속도 및 고분자 농도와 같은 결정화 변수를 변화시키면서 섬유의 물리적 성질에 미치는 영향을 관찰하였다. 이방법으로 섬유를 성장시키면 열역학적 평형온도(118.6$^{\circ}C$) 이상 인 12$0^{\circ}C$에서 성장시켰을 때 133GPa의 인장 탄성계수 3.1%의 절단신도에서 5.04GPa의 고 강력을 갖는 섬유를 얻을수 있었다. 또한 이방법에 있어서는 결정화 온도가 물리적 성질에 가장 큰 영향을 미치는 인자로 작용하였다, 고분자 농도의 영향은 0.7wt.% 이상에선 물리적 성질이 더 이상 개선되지 않았으며 오히려 장력의 증가로 불안정한 성장을 보였다. 또한 0.5wt%이하에서는 젤층의 형성이 둔화됨을 볼수 있었다. 결국 물리적 성질의 측면에서 볼 때 0.5~0.7wt%에서 최적조건을 보여주었다.

• Journal of the Korean Magnetics Society
• /
• v.14 no.4
• /
• pp.115-119
• /
• 2004

We measured in-plane 2 dimensional magnetization vector using two pick-up coil sets and investigate the relationship between magnetization vector and anisotropic magnetoresistance. We can determine magnetization vector by measuring magnetic moment in x and y direction simultaneously. As the uniaxial magnetic anisotropy of permalloy film increases, magnetoresistance approaches the expectation which is calculated from the angle between current vector and magnetization vector. Magnetoresistance ratio is linearly proportional to the y moment magnitude which is parallel to the current direction.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.80-80
• /
• 2002

Bi-Te게 열전재료는 200~400K 정도의 저온에서 에너지 변환 효율이 가장 높은 재료로써 열전냉각, 발전재료 등에 응용하기 위하여 제조방법 및 특성에 관한 많은 역구가 진행되어 왔다. 현재 산업화에 응용되고 있는 일방향응고법은 기계적 강도가 약하여 회수 율이 낮으며, 결정을 성장시키는데 비교적 장시간을 필요로 하기 때문에 제조 단가가 비싸다. 따라서 이와 같은 문제점을 보완하기 위하여 합금설계 및 가공공정에 대한 연구가 활발히 진행되고 있다. 이에 본 연구에서는 가스분사법을 이용하여 용질원자 편석감소, 고용도의 증가, 균일고용체 형성, 결정립 미세화 등 급속응고 장점을 이용하여 화학적으로 균일한 BI-TerP열전재료 분말을 제조하고, 열간압출 가공을 통하여 이방성의 향상과 함께 미세한 결정립으로 우수한 기계적 강도를 얻을 수 있도록 제조된 분말을 압출 가공하여 열전소자의 기계적 성질과 열전특성을 연구하였다. 그 결과 급속응고 및 압출 공정을 이용한 본 연구에서는 $10\mu\textrm{m}$이하의 미세한 조직과 함께 압출공정을 통하여 이방성을 향상시켰으며, 열전소자는 $2.5{\times}10^{-3}/K$이상의 Figure of merit값을 나타내는 우수한 열전특성을 나타냈다.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.8
• /
• pp.5-14
• /
• 2018

The grain size of clastic sedimentary rocks classifies the rock types and also causes of anisotropy of the rock. The anisotropy is one of the most important factors that dominates the strength and weathering behavior of rocks. The anisotropy of clastic sedimentary and igneous rocks in the Gyeongsang Basin including Yeongju, Daegu, and Busan were analyzed by magnetic susceptibility expressed by the degree of anisotropy and shape parameter. As the results of the study, the sandstone deposited under lacustrine environment unaffected by the external force shows 1.03 degree of anisotropy. The degrees of anisotropy of the rocks affected by faults and fault rocks show 1.06 and 1.14, respectively. The magnetic susceptibility of rocks is to decrease with the distance from the fault. A fresh mudstone and shale formed by fines show a similar magnitude of the degree of anisotropy to fault rock and correspond to oblate shape parameter due to their sedimentary structure. Due to these reasons, we need attention in design, construction, and maintenance of a structure constructed in mudstone and shale.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.73-82
• /
• 1998

The exchange anisotropy is the unidirectional magnetic anisotropy which comes from exchange interaction between antiferromagnetic layer and ferromagnetic layer. The application of this phenomenon to MR read head and spin-valve type GMR (Giant Magnetoresistance) head has been studied extensively. In our study, we intended to apply exchange anisotropy of NiO/NiFe bilayer to spin-valve type GMR element. Above all, we studied the exchange anisotropy of NiO/NiFe bilayer, and focused especially on the effect of NiO deposition condition. And we found that Ar pressure during NiO deposition was crucial factor for the exchange anisotropy of NiO/NiFe bilayer. The lower the Ar pressure is, the better the characteristics of exhange anisotropy is. Then, we applied this optimum condition of NiO/NiFe bilayer to spin-valve type GMR element. Finally we got spin-valve type GMR element which had 3.6 % MR ratio, 16 Oe switching field, and 0.25 %/Oe sensitivity.