• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.232-237
• /
• 2007

We have synthesized the low temperature sintered of Ni-Zn-Cu ferrite with nonstoichiometric composition a little deficient in $Fe_2O_3$ from $(Ni_{0.2}Cu_{0.2}Zn_{0.6})_{1+x}(Fe_2O_3)_{1-x}$. For low loss and acceleration of grain growth $TiO_2$ and $Li_2CO_3$ was added from 0.25 mol% to 1.0 mol%. The mixture of the law materials was calcinated and milled. The compacts of toroidal type were sintered at different temperature $(875^{\circ}C,\;900^{\circ}C,\;925^{\circ}C\;950^{\circ}C)$ for 2 hours in air followed by an air cooling. Then, effects of composition and sintering temperatures on the physical properties such as density, resistivity, magnetic induction, coercive force, initial permeability, and quality factor of the Ni-Zn-Cu ferrite were investigated. The density of the Ni-Zn-Cu ferrite was $4.85\sim5.32g/cm^3$, resistivity revealed $10^8\sim10^{12}\Omega-cm$. The magnetic properties obtained from the aforementioned Ni-Zn-Cu ferrite specimens were 1,300 gauss for the maximum induction, 4.5 oersted for the coercive force, 275 for the initial permeability, and 83 for the quality factor. The physical properties indicated that the specimens could be utilized as the core of high frequency range (involved microwave range) communication and deflection yoke of T.V.

• Journal of the Korean Magnetics Society
• /
• v.24 no.2
• /
• pp.46-50
• /
• 2014

The crystallographic properties and cationic distribution of $M_{0.2}Fe_{2.8}O_4$ (M =Mn, Ni, Cu) and $Fe_3O_4$ thin films prepared by sol-gel method have been investigated by X-ray diffraction (XRD) and conversion electron M$\ddot{o}$ssbauer spectroscopy (CEMS). The ionic valence, preferred site, and hyperfine field of Fe ions of the ferrites could be obtained by analyzing the CEMS spectra. The $M_{0.2}Fe_{2.8}O_4$ films were found to maintain cubic spinel structure as in $Fe_3O_4$ with the lattice constant slightly decreased for Ni substitution and increased for Mn and Cu substitution from that of $Fe_3O_4$. Analyses on the CEMS data indicate that $Mn^{2+}$ and $Ni^{2+}$ ions substitute octahedral $Fe^{2+}$ sites mostly, while $Cu^{2+}$ ions substitute both the octahedral and tetrahedral sites. The observed intensity ratio $A_B/A_A$ of the CEMS subspectra of the samples exhibited difference from the theoretical value. It is interpreted as due to the effect of the M substitution for A and B on the Debye temperature of the site. The relative line-broadening of the B-site CEMS subspectra can be explained by the dispersion of magnetic hyperfine fields due to random distribution of M cations in the B sites.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.5 no.3
• /
• pp.99-106
• /
• 2002

The application method of GIS for planning of forest road network can be save the efforts and cost by frequently change of forest road and evaluation the forest road route before construction. The purpose of this study is to suggest the proper method for planning an optimal forest road network in mountains forest using geographic information system(GIS) in the national forest of Mt. Kumsan at Namhae-gun, Gyungsangnam-do. In the forest road network planning by the minimum longitudinal gradient, The total length was 20.41km, and road density was 6.92m/ha. In the forest road network planning by mixed with the minimum longitudinal gradient and the maximization of investment effect, The total length was 21.15km, and road density was higher than that of the minimum longitudinal gradient as 7.17m/ha. The road length overlapped by cost path was more short than 3.52m/ha of the minimum longitudinal gradient as 1.73km. So, it appeared that forest road has an high effectiveness in yarding function. Therefore, it considered that the geographic information system could provide an effective and resonable solutions for planning of optimal forest road network.

• Clean Technology
• /
• v.18 no.4
• /
• pp.432-439
• /
• 2012

The electrocatalytic oxidation of CO was studied using carbon-supported 20 wt% PtRu (PtRu/C) catalysts, which were prepared with different Pt : Ru atomic ratios from 7 : 3 to 3 : 7 using a colloidal method combined with a freeze-drying procedure. The bimetallic PtRu/C catalysts were characterized by various physicochemical analyses, including X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). CO stripping voltammetry measurements indicated that the addition of Ru with a Pt catalyst significantly improved the electrocatalytic activity for CO electrooxidation. Among the tested catalysts, the $Pt_5Ru_5/C$ catalyst had the lowest onset potential (vs.Ag/AgCl) and the largest CO EAS. Structural modification via lattice parameter change and electronic modification in the unfilled d band states for Pt atoms may facilitate the electrooxidation of CO.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.618-619
• /
• 2010

LED는 기존의 발광원에 비해 훨씬 높은 파워와 효율성으로 인해 최근 들어 각종 조명이나 교통신호 등에서 사용이 급증하고 있다. LED 재료를 위해 지금까지 여러가지가 연구되어 왔는데, 갈륨 질화물 (Gallium Nitride, GaN)에 기반한 시스템이 최근들어 가장 큰 관심을 받고 있다. GaN 방식은 열적으로 매우 안정성이 있고, 1.9 ~ 6.2 eV 범위의 넓은 밴드의 Gap, 그리고 인듐이나 알루미늄과 결합하여 청, 녹, 백색등의 다양한 빛을 발생할 수 있는 장점을 가지고 있다. 예를 들어 청색 LED는 광학 방식의 기록매체에, 백색 LED는 기존의 조명램프의 대체용으로 활용이 가능하다. 이러한 장점 덕분에 GaN기반 LED 시장은 1994년에 최초로 상용화 된 이래 최근 급격한 성장을 보여 왔다. 그러나 GaN은 다른 III~V 타입의 반도체 재료와는 달리 재료가 성장하기 위해 사파이어와 같은 별도의 기판을 필요로 하는 문제가 있다. 이것은 결국 전위발생과 같은 격자의 부조화 같은 문제를 야기하여 결국 LED의 성능을 떨어뜨리는 요인이 된다. 이러한 문제를 해결하기 위해 HVPE(Hydride Vapor Phase Epitaxy) 방법이 개발되었는데, 이 방법은 시간당 100 미크론의 매우 빠른 성장속도로 높은 두께의 레이어를 만드는 장점이 있다. 이렇게 성장된 GaN 레이어는 베이스 기판에서 쉽게 분리되어 활용이 가능하다. 그러나 HVPE 기술은 성장 공정에서 두께를 균일하게 만들도록 제어하는 것이 매우 어렵다는 문제가 있다. 따라서 HVPE 방식에서는 이러한 조건을 만족시키기 위해 반응현상에 대한 물리적 해석을 토대로 공정조건을 정밀하게 설계해야 한다. 이를 위해 최근에 실험 또는 시뮬레이션을 활용하여 이러한 공정조건을 향상시키기 위한 여러 연구가 진행되었다. 본 연구에서는 이러한 연구의 일환으로 반응로에 투입되는 여러 기체의 유량과 존별 주변온도 조건을 입력변수로 하고, 이들이 GaN 성장에 미치는 영향을 분석하였다. HVPE 시스템에서 가장 이상적인 목표는 반응기체가 층류유동을 유지하면서 대부분의 반응이 기판위에서 이뤄지며, 기판위에서 성장되는 재료의 두께가 균일하게 되는 것이다. 입력변수들이 이러한 결과에 어떠한 영향을 미치는 지 분석하기 위해 전산유체역학(CFD, Computational Fluid Dynamics)을 수행하는 상용코드 FLUENT를 사용하였다. 보다 실제에 가까운 해석을 위해서는 기체간의 화학반응을 포함해야 하나, 해석의 편의와 효율을 위해 본 연구에서는 열 및 유동해석만을 수행하였다. 한편 실제 반응로의 우수성은 성장속도와 두께분포의 균일도를 통해 평가된다. CFD 해석을 통해 이들을 분석하기 위해 기존에 수행한 실험조건을 해석하고 해석결과의 유동패턴/압력분포를 실험결과의 성장속도/두께분포와 비교하고, 이중에서 관련성이 높은 해석결과변수를 우수성 평가에 활용하였다. 기존의 실험결과를 토대로 이러한 중요 결과변수와 함께 이들에 대한 목표값이 도출되고 나면, 입력 공정조건 - 사용기체의 유량과 주변온도 조건 - 에 대해 실험계획(DOE,Design of Experiment)을 수립하고 목표성능을 구현하기 위한 최적설계를 수행할 수 있다. 일반적으로 CFD를 통해 최적의 설계나 공정조건을 탐색하는 작업은 1회의 CFD 계산시간이 매우 오래 소요되기 때문에 쉽지 않다. 그러나 본 연구에서는 CFD와 DOE의 적절한 조합을 통해 적은 수의 해석을 가지고도 원하는 결과를 효율적으로 얻는 것이 가능함을 입증하고자 한다. 본 발표에서는 아직 이러한 연구가 완성되지 않은 시점에서 제반 연구개요를 소개하고 현 시점까지의 연구 결과 및 향후 계획을 소개하고자 한다.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.13-20
• /
• 2005

Fiber-Bragg-grating external cavity laser(FGL) modules were fabricated and experimentally analyzed. Proposed as a cost-effective solution for optical sources in the WDM-PON access network, FGL modules were packaged to TO-CAN type. We obtained a low threshold current of 13 mA, and an optical output power of 3.6 mW with a bias current of 60 mA at $25^{\circ}C$. The lasing wavelength dependencies on current and temperature were as small as 5.2 pm/mA and 30 pm/$^{\circ}C$, respectively. These change rates of the wavelength with the temperature and current are smaller than those of the DFB laser. Single-mode oscillations with the side-mode suppression ratio(SMSR) over 30 dB are maintained above the threshold current level. The FGL modules can be directly modulated at 155 Mbps, PRBS(2$^{23}$ -1) NRZ signal. Through the BER plots, we did not see the significant degradations before and after the transmission over 20km of the SMF at 155 Mb/s.

• Journal of the Korean Magnetics Society
• /
• v.16 no.2
• /
• pp.140-143
• /
• 2006

Single crystalline $CoFe_2O_4$ thin films on (100) MgO substrates were fabricated using a rf magnetron sputtering method. The deposited films were investigated for their crystallization by X-ray diffraction, Rutherford back-scattering spectroscopy and field emission scanning electron microscopy. When a cobalt ferrite film was deposited at the substrate temperature of $600^{\circ}C$, squared grains of about 200 nm were uniformly distributed in the film. However, the grains became irregular and their sizes also varied from 30 to 150 nm when the substrate temperature was $700^{\circ}C$. Hysteresis loops of a film deposited at $600^{\circ}C$ showed that the magnetically easy axis of the film was perpendicular to the substrate surface. Except for the squareness ratio, magnetic properties of the cobalt ferrite films grown by the present rf sputtering method were as good as those of the films prepared by a laser ablation method: The in-plane and perpendicular coercivities were 283 and 6800 Oe, respectively. As the thickness of the deposited film increased twice, the saturation magnetization became double but the coercivity remained unchanged. However, deposition of the Co ferrite films with a higher rf powder decreased the squareness ratio and the perpendicular coercivity of the films.

• The Korean Journal of Ecology
• /
• v.28 no.2
• /
• pp.99-103
• /
• 2005

Actual vegetation map drown with the scale 1 to 100 and Alnus japonica population in Ja-neup and Woong-neup of the Mujechi moor were described in order to monitor long-termly and preserve permanently, where is a very rare Molinietea moor and a legally protected area. A total of 3036 plots of 5m $\times$ 5m were surveyed during summer 1996. Thiessen polygons of 1491 alder trees were derived from the plot data. Actual vegetation map was illustrated by 6 cover types such as needle spike-rush type, moor-grass type, alder-moor type, eulalia type, oak forest type, and exposed site. Molinia grasses native to the moor and Miscanthus grasses alien to the moor are reciprocally dominant. The area of Molinia grasslands was rapidly in decline and alder population size was dramatically in increase in the moor, particularly in Woong-neup. In Molinietea moor preservation more attention should be focused on the regulation of a nutrient rich soil from forest road and fire.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.1
• /
• pp.1-10
• /
• 2020

The application of multiphase flows is increasingly being applied to analyze phenomena such as single phase flows where the fluid boundary changes continuously over time or the problem of mixing a liquid phase and a gas phase. In particular, multiphase flow models that take into account incompressible Newtonian fluids for liquid and gas are often applied to solve the problems of the free water surface such as wave fields. In general, multi-phase flow models require time-based the surface tracking of each fluid's phase boundary, which determines the accuracy of the final calculation of the model. This study evaluates the advection performance of representative VOF-type boundary tracking techniques applied to various CFD numerical codes. The effectiveness of the FCT method to control the numerical flux to minimize the numerical diffusion in the conventional VOF-type boundary tracking method and advection calculation was mainly evaluated. In addition, the possibility of tracking performance of free surface using CIP method (Yabe and Aoki, 1991) was also investigated. Numerical results show that the FCT-VOF method introducing an anti-diffusive flux to precent excessive diffusion is superior to other methods under the confined conditions in this study. The results from this study are expected to be used as an important basic data in selecting free surface tracking techniques applied to various numerical codes.

• Journal of the Korean Institute of Gas
• /
• v.19 no.2
• /
• pp.74-82
• /
• 2015

Carbon dioxide was designated as one of greenhouse gases that cause global warming. Among various ways to solve the $CO_2$ emission issue, the 3rd-generation biomass (algae) production is considered as a viable method to reduce $CO_2$ in the atmosphere. In this research, we propose a design of an innovative sustainable production system by utilizing the 3rd generation biomass in the environment of floating production storage and offloading (FPSO). Existing biomass production systems depend on the solar energy and they cannot continue producing biomass at night. Electricity produced from offshore wind farms also need an efficient way to store the energy through energy storage system (ESS) or deliver it real-time through power grid, both requiring heavy investment of capital. Thus, we design an offshore grid structure harnessing LED lights to supply the necessary light energy, by using the electricity produced from the wind farm, resulting in the maximized production of biomass and efficient use of wind farm energy. The final design integrates the biomass production system enhanced by LED lights with a wind power generation. The suggested NLP model for the optimal design, implemented in GAMS, would be useful for designing improved offshore biomass production systems combined with the wind farm.