• Journal of the Korean Geotechnical Society
• /
• v.30 no.7
• /
• pp.55-61
• /
• 2014

The need of geothermal energy is constantly increasing for economical and environmental utilization. Horizontal ground heat exchangers (GHEs) can reduce installation cost and increase efficiency. There are many kinds of GHEs, and it is known that slinky and spiral coil type GHEs show high thermal performance. Therefore, this paper presents experimental results of heat exchange rates in horizontal slinky and spiral coil type GHEs installed in a steel box whose size is $5m{\times}1m{\times}1m$. Dried Joomunjin standard sand was filled in a steel box, and thermal response tests (TRTs) were conducted for 30 hours to evaluate heat exchange rates by changing different pitch spaces of horizontal slinky and spiral coil type GHEs. As a result, spiral coil type GHE showed 30~40% higher heat exchange rates per pipe length than horizontal slinky type GHEs. Furthermore, long pitch interval (Pitch/Diameter=1) showed 200~250% higher heat exchange rates per pipe length than short pitch interval (Pitch/Diameter=0.2) in both spiral coil and horizontal slinky type GHEs, respectively.

• Korean Journal of Plant Resources
• /
• v.24 no.2
• /
• pp.174-180
• /
• 2011

This study was conducted to investigate the optimum condition of extraction from fronds of Osmunda japonica to increase antioxidant compounds and antioxidant activity. Powder (1 g) of lyophilized fronds were mixed with three different solvents (MeOH, 80% EtOH and water). Extraction was carried out using not only by immersion (room temp.), heating ($60^{\circ}C$) and stirring (200 rpm) for 6 h, but also by sonication in 42 kHz ultrasonic bath for 15, 30 and 45 min. Extracts were filtered, and adjusted up to 50 mL to determine contents of soluble solids, total polyphenols and total flavonoids. Antioxidant capacity was measured by radical scavenging activity of 0.15 mM DPPH (2,2-diphenyl-1-picrylhydrazyl) and 7.4 mM ABTS [2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid)] radical. Among the solvents, MeOH and 80% EtOH appeared to be effective for extraction. Extract obtained from sonication in MeOH for 15 min resulted high polyphenol contents (45.15 $mg{\cdot}g^{-1}$ db) and DPPH radical scavenging activity ($RC_{50}$= 0.35 $mg{\cdot}mL^{-1}$). The highest flavonoid contents was obtained from immersion or heating extraction with MeOH (38.10~38.10 $mg{\cdot}g^{-1}$ db). ABTS radical scavenging was high in same extraction with 80% EtOH ($RC_{50}$= 0.21~0.22 $mg{\cdot}mL^{-1}$). Altogether, our results indicate that the extraction using ultrasonic bath with MeOH as a solvent (for 15~30 minutes) was the most effective way not only for increasing various antioxidant activities but also for saving labor and time in case of fronds of Osmunda japonica.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.10 no.2
• /
• pp.132-139
• /
• 2002

This study was carried out to investigate the effects of aging and soil texture on composting of diesel-contaminated soil. The soils used for this study were silt loam and sand. Target contaminant, diesel oil, was spiked at 10,000mgTPH/kg of dry soil. Aging times of diesel-contaminated soils were 15days and 60days, respectively. Fresh diesel-contaminated soil was also investigated. Moisture content was controlled to 70% of soil field capacity. Mix ratio of soil to sludge was 1:0.3 as wet weight basis. Temperature was maintained at $20^{\circ}C$ Volatilization loss of TPH was below 2% of initial concentration. n-Alkanes lost by volatilization were mainly by the compounds of C10 to C17. Diesel in contaminated soil was mainly removed by biodegradation mechanism. First order degradation rate constant of TPH in sandy soil was ranged from 0.081 to 0.094/day, which is higher than that in silt loam(0.056-0.061/day). From fresh to 60day-aged soils, there was little difference of TPH biodegradation rate between the soils. Carbon recovery ranged from 0.61 to 0.89. TPH degradation rate was highly correlated with $CO_2$ production rate.

• Journal of Aquaculture
• /
• v.18 no.2
• /
• pp.115-121
• /
• 2005

This study was performed to investigate the formation and mass production of resting eggs by freshwater rotifer, Brachionus calyciflorus as influenced by different aeration supplements and exchange intervals of culture water in 15-L culture vessels and 500 L culture tanks. The maximum densities and mixis rates of the rotifers were not different between experimental group exposed to air or oxygen supplements. However, the fertilization rate and formation of resting eggs of the rotifers in the air-supplemented group were significantly higher than those in the oxygen supplemented group. In the experiment concerning exchange interval of culture water, the maximum density of the rotifers and formation of resting eggs in the batch culture were significantly higher than those in the semi-continuous culture with exchange of water every day. The formation of resting eggs per Chlorella dry weight was highest in the semi-continuous culture with exchange of water every day. The resting eggs of rotifers were produced at a density of $51.8{\sim}57.9{\times}10^6$ eggs in 500-L culture tanks. In this study, the batch culture with air is an effective method for mass production of resting eggs by the freshwater rotifer, B. calyciflorus, and the efficiency of mass production of resting eggs by this rotifer was similar to that of the seawater rotifers, B. plicatilis and B. rotundiformis.

• Membrane Journal
• /
• v.19 no.4
• /
• pp.291-301
• /
• 2009

Double-layered polymer electrolyte membranes were prepared from two different sulfonated poly(aryl ether sulfone) copolymers by the two-step solution casting method for direct methanol fuel cells (DMFC). Sulfonation degrees were adjusted 10% (SPAES-10) and 50% (SPAES-50) by controlling monomer ratios, and the weight ratios of SPAES-10 copolymer were varied in the range of 5~20% to investigate the effect of thickness of coating layers on the membranes. Proton conducting layers were fabricated from SPAES-50 solutions of N-methyl-2-pyrrolidone (NMP) by a solution casting technique, and coating layers formed on the semiliquid surface of the conducting layer by pouring of SPAES-10-NMP solutions onto. It was found that double-layered polymer electrolyte membrane could significantly reduce the methanol crossover through the membrane and maintain high proton conductivities being comparable to single-layered SPAES-50 membrane. The maximum power density of membrane-electrolyte assembly (MEA) at the condition of $60^{\circ}C$ and 2 M methanol-air was $134.01\;mW/cm^2$ for the membrane prepared in the 5 wt-% of SPAES-10 copolymer, and it was corresponding to the 105.5% of the performance of the commercial Nafion 115 membrane.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.3
• /
• pp.679-685
• /
• 2004

Although the electrophoretic deposition method has the advantage of simple processing procedure, less fabrication facilities, and easier control for deposition thickness and wire length, providing economical and technical merits, it also has the disadvantages of cracking and porosity phenomena, requiring an improved processing method for higher particle density and constant particle orientation. we have developed an optimization method to increase the particle density and to unify its orientation, and have performed a study to overcome the cracking and porosity problems in the fabricated superconductor. In order to improve the surface uniformity and the conduction properties of the fabricated YBCO thick films, a system that applies alternate voltage vertically has been developed for the first time and applied to the electrophoretic deposition process. The applied alternate electric field caused a force to be exerted on each YBCO particle and resulted in a rotation of the particle in the direction of applied electric field, accomplishing a uniform particle orientation. We name this process as the shaky-aligned electrophoretic deposition method. For commercial utilization and efficiency, in this dissertation, alternating voltage of 60 Hz and 25 ∼ 120 V/cm was proposed to apply it as a subsidiary source for shaky-flow deposition so that the fabricated thin film showed uniform surface morphology with less voids and cracks and Tc,zero of 90 K and the critical current density of 3419 A/$cm^2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.173-173
• /
• 2013

최근에 고효율의 형광체를 개발하고자 무기물 모체에 주입된 희토류 이온의 발광에 대한 연구가 급부상하고 있다. 형광체는 고휘도, 넓은 시청 각도와 저 비용으로 인하여 대형 평판 디스플레이 분야로 그 응용성을 확장하는 플라즈마 디스플레이 패널 제작에 있어서 매우 중요한 물질이다. 현재 적색 형광체로 널리 사용되고 있는 발광 물질은 YBO3:Eu3+ 혹은 (Y,Gd)BO3:Eu3+ 형광체이지만, Eu3+ 이온이 중심대칭의 자리에 위치하기 때문에, Eu3+ 이온의 5D07F1 전이에 의한 주황색의 발광 세기가 5D07F2 전이에 의한 적색의 세기보다 강하여 고품질의 색상을 구현하는데 상당한 어려움이 있다. 이러한 문제점을 해결하기 위하여 새로운 모체 격자를 갖는 적색, 녹색, 청색 형광체 개발에 많은 노력이 집중되고 있다. 본 연구에서는 형광체 합성시 중요한 변수의 하나인 소결 온도가 새로운 다양한 색을 방출하는 형광체 분말 CaSiO4:RE3+ (RE=Eu, Sm, Tb, Dy, Ce)의 특성에 미치는 영향을 조사하였다. CaSiO4:RE3+ (RE=Eu, Sm, Tb, Dy, Ce) 형광체 분말 시료는 초기 물질 CaO (99.99%), SiO2 (99.99%), Eu2O3 (99.99%), Sm2O3 (99.9%), Tb4O7 (99.9%), Dy2O3 (99.9%), CeO2 (99.9%)을 화학적량으로 준비하였다. 볼밀, 건조 작업을 한 후에, 시료를 막자사발에 넣고 분쇄하여 3시간의 하소 공정과 5시간의 소결 공정을 수행하였다. 이때 소결 온도를 변수로 선택하여 각각 $800^{\circ}C$, $900^{\circ}C$, $1,000^{\circ}C$, $1,100^{\circ}C$에서 소결 작업을 수행하여 합성 분말의 구조, 표면, 광학적 특성을 측정하여 소결 온도가 미치는 영향을 조사하였다. Eu3+가 도핑된 CaSiO4 형광체 분말의 경우에, 발광 스펙트럼은 597, 618, 655, 707 nm에서 관측되었으며, 소결 온도가 $800^{\circ}C$에서 $1,100^{\circ}C$로 증가함에 따라 모든 발광 스펙트럼의 세기는 순차적으로 증가함을 나타내었다. Tb3+가 도핑된 CaSiO4 형광체 분말의 경우에 관측된 발광 스펙트럼은 주 피크인 549 nm를 중심으로 하여 세기가 상대적으로 작은 493, 592, 626 nm의 피크들이 관측되었으며, 소결 온도가 증가함에 따라 전반적으로 발광 세기들이 증가하는 경향을 나타내었다. Sm3+가 도핑된 CaSiO4 형광체의 경우에, 발광 스펙트럼은 전형적인 Sm3+이온에 의한 전이 신호들이 605, 570, 653 nm에서 나타났다. 발광 스펙트럼의 세기는 소결 온도에 비례하여 증가하였다. Ce3+가 도핑된 경우에 발광 스펙트럼은 소결 온도에 관계없이 401 nm에서 관측되었으며, 소결 온도에 따라 발광 세기의 변화가 나타났다. 이 실험 결과로 부터, 합성시 적절한 소결 온도의 선택이 고발광 효율의 형광체를 제작하는데 있어서 매우 중요한 요소가 됨을 확인할 수 있었다.

• Resources Recycling
• /
• v.15 no.4 s.72
• /
• pp.36-43
• /
• 2006

There was some difficulty dewatering properties due to small porosity diameter of cake, when pigment sludge contained fine particle was formed by cake under the dewatering. It was difficult to dewater the sludge with fine particles with the conventional mechanical dewatering method. This study was to improve the dewatering rate as discharging the water from porosity of cake easily, supplying the low heat to the cake layer. Thermal dewatering equipment of piston type to keep up constant temperature on the cake was set up and relative experiment was conducted for sludge of 200 g with fine pigment particle. As test results. filtration of 176.8 g, cake weight of 19.4 g, cake thickness of 4.2 mm was measured, and it was analyzed that the water content of cake was 47 wt% and dewatering velocity, which moaned the residual d교 sloid amount per dewatering area, was $2.1DS\;m^{2}{\cdot}cycle$. This results showed that filtration increased, cake weight and thickness decreased and dewatering velocity increased against mechanical dewatering method. And water content of cake decreased about 30%, so the result which dewatering rate improved was drew generally. The reason is that the inner vapor pressure working at the cake porosity increased as applying the low heat to the cake layer, which lead to discharge the water from porosity easily. Therefore, this study was estimated by the useful technology for sludge reduction.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.4
• /
• pp.148-154
• /
• 2019

Vanadium oxide based materials have been studied as novel negative electrode materials in lithium-ion batteries (LIBs) because of their high specific capacity. In this study, potassium metavanadate ($KVO_3$) was synthesized and its electrochemical properties are evaluated as a negative electrode materials. The aqueous solution of $NH_4VO_3$ is mixed with a stoichiometric amount of KOH. The solution is boiled to remove $NH_3$ gas and dried to obtain a precipitate. The obtained $KVO_3$ powders are heat-treated at 300 and $500^{\circ}C$ for 8 h in air. As the heat treatment temperature increases, the initial reversible capacity decreases, but the cycle performance and Coulombic efficiency are improved slightly. On the contrary, the electrochemical performances of the $KVO_3$ electrodes are greatly improved when a polyacrylic acid (PAA) as binder was used instead of polyvinylidene fluoride (PVDF) and a fluoroethylene carbonate (FEC) was used as electrolyte additive. The initial reversible capacity of the $KVO_3$ is 1169 mAh/g and the Coulombic efficiency is improved to 76.3% with moderate cycle performance. The $KVO_3$ has the potential as a novel high-capacity negative electrode materials.

• Journal of Navigation and Port Research
• /
• v.42 no.6
• /
• pp.415-420
• /
• 2018

The Energy Efficiency Design Index (EEDI) introduced by the Marine Environment P rotection Committee(MEPC) in International Maritime Organization(IMO) has significantly assisted in regulating CO2 emissions. However, in adverse weather conditions, it can lead to accidents due to slow steaming of vessels and low engine propulsion power. In response to this issue, the MEPC presented guidelines for the minimum propulsion power of the main engine for maintaining the course of vessels in adverse weather conditions. However, the guidelines are only applicable for vessels with a deadweight of 20,000 tons, leaving out small and medium ships. This study evaluated vessels subject to the guidelines of minimum propulsion power and proposed revised guidelines. In addition, relevant cases of marine accidents were investigated with the aim of investigating the minimum propulsion power of main engine for medium and small ships not covered by the guidelines. In order to achieve this, engine propulsion power was analyzed according to the size of the affected vessels. The results obtained from this study could be used as a minimum power criterion that can be considered for ship building to reduce marine accidents in adverse weather for small and medium ships.