• Journal of the Korean GEO-environmental Society
• /
• v.8 no.6
• /
• pp.5-12
• /
• 2007

Mudstone has characteristics that it has high enough strength and stiffness in a dry condition, but the strength and stiffness decrease in a wet condition with groundwater infiltration. The sliding of cut slope frequently encountered in Pohang area has been reported due to the rapid reduction of shear strength in mudstone after being exposed to the air. The study in this paper shows that mudstone having enough strength in a boring stage has lost the strength after installing PRD (percussion rotary drill) steel pipe pile inducing an insufficient bearing capacity. Field test has been performed to investigate the most favorable method for increasing a pile bearing capacity in mudstone with various methods such as MSG (Micro Silica Grouting) around the tip and side of a pile, the perimeter grouting combined with Micro pile reinforcement, and concrete filling after tip reinforcing grouting. MSG has been turned out to be the most favorable method for increasing a pile bearing capacity in mudstone, confirmed by the static load test.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.1
• /
• pp.53-61
• /
• 2014

Sea gives us a lot of benefits and one of them is a role of transporting goods easily by ship. Accordingly the industrial area or the container yard is constructed either on the low sea or near the sea. Sea dredging ground is made by pumping them using dredge pump to the inside of embankment after dredging undersea soils. The dredging ground after pumping is in the slurry state but as time goes, consolidation by the own weight happens and evaporation happens at the surface of dredging ground. The evaporation causes the crest layer in the upper side of dredging ground. Under the crest layer there is still a soil of slurry state which has just little bearing resistance. This kind of characteristics makes it difficult to get a exact bearing capacity using the equations proposed until now. In this study we have performed simultaneously both the field loading tests and the cone penetration tests on the sea dredging ground. From the result of field tests, new experimental equation for the ultimate bearing capacity has been proposed. If we use the new equation, it is believed that some design of sea dredging ground could be more accurate.

• Journal of the Korean earth science society
• /
• v.28 no.7
• /
• pp.947-956
• /
• 2007

In this article, the extratropical transition (ET) of tropical cyclone (TC) was investigated based on the case study covering the latest three TCs (Shanshaa Yaki, and Soulik) associated with ET evolution (onset and completion) using the objective 37 diagnostics of Evans and Hart (2003) and Hart (2003). At 500-hPa level, on an onset of ET, all three TCs entered the baroclinic zone. In a vertical cross-section analysis, three TCs before and at an onset of ET kept warm and humid throughout all levels around the TC center. However, these TCs after ET onset became relatively cold and dry over the western part of TC as the typical characteristics of ET concept model. Although our case study was not sufficient, it is concluded that the diagnostics of the ET onset and atmospheric structure change associated with Evans and Hart (2003) and Hart (2003) will be useful in ET operational forecast.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.73.2-73.2
• /
• 2011

석탄 합성가스 중에는 $H_2S$, HCl, $NH_3$와 같은 불순물이 포함되어 있다. 이러한 가스들은 오염가스 배출과 관련한 환경기준 준수와 터빈과 같은 설비의 보호를 위해 제거되어야 한다. 석탄 합성가스 중 HCl 농도는 탄종에 따라 다르기는 하지만 많게는 1000 ppmv 수준까지 존재한다. 합성가스를 이용하여 발전을 하는 경우 가스터빈 보호를 위해 HCl은 <3 ppmv 이하로 정제되어야 하고, 합성가스를 연료전지에 사용하고자 하는 경우에는 HCl을 <0.5 ppmv 수준까지, 화학원료로 사용하고자 하는 경우에는 <10 ppbv 수준까지 정제하여야 한다. 또한 HCl은 고온 탈황공정에 사용되는 흡수제의 활성에도 장기적으로 부정적인 영향을 주기 때문에 고온에서 HCl을 정제할 수 있는 흡수제가 필요하다. 본 연구에서는 알칼리금속을 활성물질로 사용하여 분무건조법으로 제조한 HCl 흡수제에 대해 물성 및 HCl과의 반응성을 살펴보았다. $300-500^{\circ}C$ 영역에서 K-계 및 Na-계 흡수제에 대해 고정층반응기에서 HCl 가스를 함유한 모사 합성가스를 이용하여 상압 조건에서 Cl 흡수능을 측정한 결과 15wt% 이상의 흡수능을 나타내었으며 반응온도가 높을수록 흡수능이 증가함을 알 수 있었다. XRD 분석을 통하여 Cl은 K 및 Na와 반응하여 KCl과 NaCl을 형성하면서 흡수됨을 알 수 있었다. 20 bar 조건에서 실험한 결과에서도 동일한 경향의 반응성을 나타내었으며 반응온도가 낮을수록 흡수능은 감소하지만 Cl을 더 낮은 농도로 정제할 수 있었다. 본 실험에 사용된 Na 및 K계 흡수제는 모두 연소 후 배가스 중 $CO_2$를 제거하기 위한 흡수제로 사용되는 고체 흡수제이다. 석탄화력발전소 배가스에 연계되어 $CO_2$ 회수실험에 사용되었던 사용 후 $CO_2$ 흡수제에 대해 HCl 흡수 실험을 수행한 결과에서도 우수한 HCl 제거 성능을 보여 주었다. 이로부터, 폐 $CO_2$ 흡수제의 HCl 흡수제로서의 활용가능성을 확인 하였다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.6
• /
• pp.547-557
• /
• 2013

The mode II fracture toughness and strength due to shear stress are important parameters in the stability of caprock and injection zone with application to geological sequestration of carbon dioxide. In this research, a short beam compression test has been used to determine the shear strength and the mode II fracture toughness for Coconino sandstone. The average value of the shear strength and mode II fracture toughness are estimated to be 23.53 MPa and 1.58 MPa${\surd}$m respectively. The stress intensity factor is suggested by finite element analysis using the displacement extrapolation method. The effect of biaxial stress and water saturation on the fracture toughness has also been investigated. The fracture toughness increases with confining stresses, but decreases by 11.4% in fully saturated condition.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05a
• /
• pp.30-32
• /
• 2012

본 연구에서는 Cu, Mn을 함침 시킨 상용 제올라이트13X 촉매에 CO 산화 전환 반응에 영향을 연구하였다. 촉매 제조는 담지량별로 Cu, Mn을 서로 다른 비율로 물리 혼합하여 상용 제올라이트에 담지하였다. 함침방법은 과잉용액 함침법을 사용하였고, 건조 후 공기분위기에서 소성하여 산화물 형태로 담지하였다. 기본적인 촉매 특성은 X-선 회절분석, 질소흡탈착 등온곡선을 이용하여 기공크기, 기공부피, 비표면적을 구하였으며, FT-IR, 주사현미경, $NH_3$-TPD/TPR, EDX로 특성을 분석하였다. 촉매 산화반응 실험은 고정층 반응기에서 수행하였으며, 외경1/4 inch(내경 4 mm)석영관에 촉매를 중진하고 Gas Chromatograph로 배출가스를 측정하여 Cu-Mn 제올라이트 촉매의 일산화탄소 산화반응을 연구하였다. 일산화탄소 농도, 온도 및 공간속도, Cu-Mn 함량 비율에 따른 산화반응 실험을 수행하여 최적 산화조건과 촉매를 도출하였다.

• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.421-426
• /
• 2001

11-Aminododecanoic acid, to insert the functional group of -COOH reacted with the end group of poly($\varepsilon$-caprolactone) diol, and cetyltrimethylammonium bromide (CTMA), to increase the d-spacing of Montmorillonite (MMT), were intercalated into $Na^+;_-$MMT. The modified MMT was reacted with poly(${varepsilon}-caprolactone$) diol ($M_n{=2000$) in THF solution at $80^{\circ}C$ for 4 hrs. After reaction, poly(${varepsilon}-caprolactone$) ($M_n{=80000$) was mixed into the solution for 12 hrs. To prepare the PCL/clay nanocomposite film this solution was cast into the silicon mold at $60^{\circ}C$ in vacuum oven for 6 hrs. From the results of XRD and TEM, it was found that the exfoliated PCL/clay nanocomposite were prepared. The effects of the amount of MMT on the mechanical properties and thermal properties of PCL/clay nanocomposites have been investigated by tensile tester and DSC. Because the MMT was dispersed homogeneously in PCL matrix, the Young's modulus of the nanocomposite were found to be excellent. However, MMT dispersed in PCL matrix had almost no effect on the tensile strength of the composites. The crystallization temperature of PCL increased in proportion to 3 wt% MMT in the PCL matrix.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.704-707
• /
• 1997

The preparation of alumina sol for fine chemical field from kaolin-derived aluminum sulfate solution is performed. Noncrystalline AlO(OH) was prepared by dropping ammonia water into aluminum sufate solution with stirring. Acetetic acid was added to form the electrical double layers on the particle surface of the slurry, which resulted in a stable sol. The influence of the reaction temperature, reaction time, acetetic acid concentration on the preparation of alumina sol were investigated. Dispersed colloid particles of AlO(OH) were prepared at the reaction temperature of $50{\sim}90^{\circ}C$ and 1.6 A/C = 1.6 (molar ratio), regardless of the reaction time. Stable alumina sol having a particle size of about 5~10 nm was prepared in the range 1~5 vol% alumina content.

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.229-232
• /
• 2000

The carbon dioxide, nitrogen, and phosphate removals from wastewater using microalgae have extensively been studied. Especially, the green colonial algae Botryococcus braunii is characterized by unusual high hydrocarbon contents, ranging from 15 to 75% of dry weight, as long-chain unsaturated hydrocarbons. These hydrocarbons suggest that the possibility of renewable biofuels to be converted into useful fuels such as gasoline by simple catalytic cracking. The poor recovery (18 - 32%) of hydrocarbon from B. braunii culture in two-phase bubble column seems to be caused by insufficient mixing between two phases, which was operated using only aeration on the narrow interface between hydrophobic solvent and cell suspension. In addition, hydrocarbon was entrapped tightly in cell-matrix (formed by exopolysaccharide) of algal colony, which make difficult to extract using two-phase system. In order to overcome low recovery efficiency, two-stage extraction culture system including culture vessel and two-phase separator is now under development, resulted improving contact between solvent phase and cell suspension. Hydrocarbon recovery using this process was more than two times as that using two-phase extraction culture.

• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.70-78
• /
• 1997

3Y-TZP/SUS316 Functionally Graded Material (FGM) was fabricated by slip casting method. Alumina mold was used to overcome problems of gypsum mold in slip casting process, and the optimal dispersion con-ditions of 3Y-TZP/SUS316 binary slurries was determined using electrokinetic sonic amplitude and a viscometer, and observing sedimentation behavior. The properties of the specimens casted by gypsum mold and alumina mold were compared in terms of changes in shrinkage rate, drying and sintering conditions, and microstructure. It was found that the specimens obtaine from the alumina mold showed a clean surface, easier thickness control of each layer, and higher productivity. Especially, no degradation was observed in the SUS316 prepared using alumina mold. Thus it is desirable to use porous alumina mold rather than gyp-sum mold for the slip casting of 3Y-TZP/SUS316-FGM.