• Food Science and Preservation
• /
• v.24 no.7
• /
• pp.957-964
• /
• 2017

The purpose of this study was to determine the optimum spray drying conditions of soft persimmon latte using response surface methodology that is a statistical procedure used for optimization studies. A central composite design was applied to investigate the effects of independent variables, inlet temperature ($X_1$), air flow rate ($X_2$), and feed flow rate ($X_3$), on responses such as yield, water absorption index, and total phenolic compounds. Statistical analysis revealed that independent variables significantly affected all the responses. A maximum yield of 8.11 g was obtained at $90^{\circ}C$ of $X_1$, 51.82 mL/min of $X_2$ and 7.00 mL/min of $X_3$. A minimum water absorption index of 0.58 was obtained at $101^{\circ}C$ of $X_1$, 60.00 mL/min of $X_2$ and 17.00 mL/min of $X_3$. A maximum total phenolic compounds of $298.02{\mu}g/mL$ was obtained at $90^{\circ}C$ of $X_1$, 43.33 mL/min of $X_2$ and 17.00 mL/min of $X_3$. In conclusion, the best spray drying conditions were as follows: $X_1$, $90^{\circ}C$; $X_2$, 53 mL/min; $X_3$, 17 mL/min. Under those optimal conditions, the powder's yield (7.46 g), water absorption index (0.54), and the content of total phenolic compounds ($294.75{\mu}g/mL$) were estimated.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.31 no.2
• /
• pp.343-350
• /
• 2002

This study was conducted to standardize the manufacturing process of doenjang. The preparation methods, kinds and levels of the ingredients were determined by the statistical surveys of literatures obtained from cooking books, scientific papers and doenjang manufacturing factories. The standardized preparation of fermentation methods of doenjang were classified into two large groups, that were traditional and modified (commercialized) methods. Most soybeans used in doenjang preparation were the large size. To prepare traditional doenjang, soybeans were cleaned, scaled and cooked for 2 hrs at atmospheric pressure. These cooked soybeans were crushed in water and molded as brick shape. The molded soybean was dried for 2 days in the air, hung up by rice straw and fermented for 30~60 days under natural environmental condition (called meju). Recently soybean grain meju that inoculated with Asp. oryzae also frequently used to make traditional doenjang. The fermented meju was brined with a ratio of meju : salt : water = 18.4 : 14.6 : 67.0 and the meju-brine mixtures were ripened for 2 months. When the meju-brine mixture was fully fermented, it was separated into liquid and solid parts. The crushed solid part was further ripened in a separated pottery for 60 days and become doenjang. The liquid part was filtered, boiled and used as soy sauce. In modified commercial doenjang preparation, soybeans were cocked by autoclaving and then cooled about to 3$0^{\circ}C$. Separately, steamed barley grains or wheat flour were inoculated with 0.2% Asp. oryzae and incubated for 3 days at 3$0^{\circ}C$ and mixed with the crooked soybeans, salt, and water (soybean : salt : starch : water = 39.8 : 12.5 : 22.6 : 25.1). These mixtures were ripened for 30 days at 3$0^{\circ}C$. It seems that the manufacturing process of traditional doenjang needs to be more industrialized, whereas, the commercial doenjang preparation is going to adapt the traditional processing method of doenjang.

• Journal of Aquaculture
• /
• v.16 no.4
• /
• pp.233-239
• /
• 2003

Growth and activities of digestive enzymes in slime flounder (Microstomus achne) larvae were measured from hatching to near the end of larval development (day 58). Larvae reared under starved and fed conditions and the changes of acid phosphatase (ACPase) specific activity, alkaline phosphatase (ALPase) specific activity, trypsin-like enzyme activity and pepsin-like enzyme activity were described with growth and developmental stage of larvae. Total length of the starved larvae was gradually increased for 7 days post hatching and then almost unchanged. Total length of the fed larvae ranged from 5.13$\pm$0.178 mm at the day of hatching to 13.43$\pm$1.395 mm at 58 days after hatching. In starved group, dry body weight decreased from 0.l0$\pm$0.020 mg at the day of hatching to 0.05$\pm$0.012 mg at 12 days after hatching. Dry body weight of fed larvae decreased during the prelarva stage like starved group and then gradually increased. ACPase and ALPase specific activity in the starved larvae increased until all larvae died, however those activities in the fed larvae increased until 20 days and then decreased until 58 days after hatching, with no significant difference between groups. Trypsin-like enzyme activity in the starved larvae was unchanged until 3 days and then was the highest on 5 days after hatching, but not detected after completion of yolksac absorption. Those of fed larvae decreased until 3 days and sharply increased until completion of yolksac absorption. The highest trypsin-like enzyme activity in the fed group was observed at 20 days after hatching. Trypsin-like enzyme activity in the fed larvae was significantly higher than that in the starved larvae from 8 days after hatching. Pepsin-like enzyme activity was increased in 5 days after hatching in both groups. There was significant difference at 8 and 10 days after hatching between both groups. Based on above results, digestive enzyme activities were correspondingly changed to a growth and morphological transformation. Trypsin-like enzyme and pepsin-like enzyme activities are able to be a useful indices for health and growth status in larval slime flounder, because there was significant difference in digestive enzyme activities with developmental stages, growth or feed supply.

• Asian Journal of Turfgrass Science
• /
• v.24 no.1
• /
• pp.45-49
• /
• 2010

Research on nitrate-nitrogen ($NO_3-N$) leaching in turfgrass indicates that in most cases leaching poses minimal risk to the environment. Although there have been many studies investigating $NO_3-N$ leaching, there has been little research to investigate the effect of compaction level and rootzone mix on nitrogen (N) leaching. The research objective is to determine the effect of compaction level and rootzone mix on nitrogen leaching. The four rootzone mixes are 76.0:24.0, 80.8:19.2, 87.0:13.0 and 93.7:6.3 % (sand:soil). The four levels of compaction energies are 1.6, 3.0, 6.1, and 9.1 J $cm^{-2}$. Nitrogen was applied using urea at a rate of 147 kg $ha^{-1}$ split among three applications. Rootzone was packed into a polyvinylchloride pipe with a perforated bottom to facilitate drainage. Rootzone depth was 30 cm over a 5 cm gravel layer. Each column was sodded with Poa pratensis L. Hoagland solution designed for coolseason grasses, minus N, was used to ensure adequate nutrition in the rootzone. Turf grass quality and clipping yield were recorded from each tube at two-week intervals. The clippings were oven-dried at a temperature of $67^{\circ}C$ for 24 h and weighed. At the end of the study, root dry weight was determined by washing and oven-drying samples at $67^{\circ}C$ for 24 h. Leachate solution was collected weekly for analysis. More than 6.1 J $cm^{-2}$ of compaction energy increased possibilities of surface runoff. The compaction energy between 3.0 and 6.1 J $cm^{-2}$ produced more clipping dry weight and less N leaching than 9.1 J $cm^{-2}$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.3
• /
• pp.177-184
• /
• 2020

Purpose: The purpose of this study was to compare and evaluate the tensile bond strength of chairside reline resin to denture base resin fabricated by different methods (subtractive manufacturing, additive manufacturing, and conventional heat-curing). Materials and methods: Denture base specimens were fabricated as cuboid specimens with a width of 25 mm × length 25 mm × height 3 mm by subtractive manufacturing (VITA VIONIC BASE), additive manufacturing (NextDent Base) and conventional heat-curing (Lucitone 199). After storing the specimens in distilled water at 37℃ for 30 days and drying them, they were relined with polyethyl methacrylate (PEMA) chairside reline resin (REBASE II Normal). The subtractive and additive manufacturing groups were set as the experimental group, and the heat-curing group was set as the control group. Ten specimens were prepared for each group. After storing all bound specimens in distilled water at 37℃ for 24 hours, the tensile bond strength between denture bases and chairside reline resin was measured by a universal testing machine at a crosshead speed of 10 mm/min. The fracture pattern of each specimen was analyzed and classified into adhesive failure, cohesive failure, and mixed failure. Tensile bond strength, according to the fabrication method, was analyzed by 1-way ANOVA and Bonferroni's method (α=.05). Results: Mean tensile bond strength of the heat-curing group (2.45 ± 0.39 MPa) and subtractive manufacturing group (2.33 ± 0.39 MPa) had no significant difference (P>.999). The additive manufacturing group showed significantly lower tensile bond strength (1.23 ± 0.36 MPa) compared to the other groups (P<.001). Most specimens of heat-curing and subtractive manufacturing groups had mixed failure, but mixed failure and adhesive failure showed the same frequency in additive manufacturing group. Conclusion: The mean tensile bond strength of the subtractive manufacturing group was not significantly different from the heat-curing group. The additive manufacturing group showed significantly lower mean tensile bond strength than the other two groups.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.4
• /
• pp.685-695
• /
• 2004

The aim of this study was to evaluate the resistance to degradation and to compare the wear resistance characteristics of four composite resins in an alkaline solution. The resistance to degradation was evaluated on the basis of mass loss(%), degradation depth(${\mu}m$), Si loss(ppm) and wear depth. The brands studied were Heliomolar flow, Filtek supreme, Point4, Tetric flow. The results were as follows: 1. The sequence of the mass loss was in descending order by Heliomolar flow, Filtek supreme, Point4, Tetric flow. There was significant differences among the materials except Heliomolar flow and Filtek supreme. 2. The sequence of the degree of degradation layer depth was in descending order by Filtek supreme, Heliomolar flow, Tetric flow, Point4. There were significant differences among the materials except Heliomolar flow and Tetric flow. 3. The sequence of Si loss was in descending order by Filtek supreme, Heliomolar flow, Point4, Tetric flow. There were significant differences among the materials except Point 4 and Tetric flow. 4. The sequence of maximum wear depth was in descending order by Heliomolar flow, Point4, Fillet supreme, Tetric flow and there was increasing wear depth on soaking in 0.1N NaOH solution. 5. When observed with SEM, destruction of bonding between matrix and filler was observed and when observed with CLSM, the depth of degradation layer of specimen surface was observed. There results indicate that wear and hydrolytic degradation could be considered to be evaluation factors of composite resins.

• Food Science and Preservation
• /
• v.24 no.1
• /
• pp.84-92
• /
• 2017

Chicken breast jerky (CJ) was prepared by drying chicken breast at $50^{\circ}C$ for 9 hrs after marinating it in a various sweetening sauce including white sugar (WS), brown sugar (BS), rice syrup (RS), fructooligosaccharide (FO), pineapple concentrate (PC), Rubus coreanus extract (RCE), or honey (H), and its physicochemical and sensory properties were investigated. The CJ was found to contain 22.5-25.0% moisture, 41.0-46.6% protein, and 0.4-1.0% fat, which indicates that it could serve as a high-protein and low-fat snack. The type of sweeteners significantly affected the yield, pH, total viable cell count, and water activity of the CJ, showing ranges of 40.9-50.1%, 5.2-5.9, $2.5-6.2{\times}10^4CFU/g$, and 0.74-0.81, respectively. Both the water activity and pH were the lowest in CJ-RCE where of the highest in CJ-WS. The cohesiveness, springiness, and chewiness of the CJ significantly differed depending on the type of sweeteners (p<0.05). CJ-RCE showed the best taste and overall acceptability in a sensory test. After storage at $50^{\circ}C$ for 2 weeks, thiobarbituric acid reactive substance (TBARS) content (58.3 malondialdehyde (MDA) mg/kg) of CJ-RCE was much lower than those of control beef (75.6 MDA mg/kg) and pork jerky (98.0 MDA mg/kg), showing the good oxidative stability of CJ-RCE. Overall, marination in RCE sauce was suitable for the preparation of CJ with good quality in terms of its water activity, fat and protein contents, sensory property and oxidative stability.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.4
• /
• pp.199-207
• /
• 2016

This study was conducted to develop a forest fire occurrence model using meteorological characteristics for practical forecasting of forest fire danger rate by reflecting the climate change for the time period of 2000yrs. Forest fire in South Korea is highly influenced by humidity, wind speed, temperature, and precipitation. To effectively forecast forest fire occurrence, we developed a forest fire danger rating model using weather factors associated with forest fire in 2000yrs. Forest fire occurrence patterns were investigated statistically to develop a forest fire danger rating index using times series weather data sets collected from 76 meteorological observation centers. The data sets were used for 11 years from 2000 to 2010. Development of the national forest fire occurrence probability model used a logistic regression analysis with forest fire occurrence data and meteorological variables. Nine probability models for individual nine provinces including Jeju Island have been developed. The results of the statistical analysis show that the logistic models (p<0.05) strongly depends on the effective and relative humidity, temperature, wind speed, and rainfall. The results of verification showed that the probability of randomly selected fires ranges from 0.687 to 0.981, which represent a relatively high accuracy of the developed model. These findings may be beneficial to the policy makers in South Korea for the prevention of forest fires.

• The Korean Journal of Mycology
• /
• v.22 no.3
• /
• pp.222-228
• /
• 1994

In Lentinus edodes(oak mushroom) cultivation, commonly are logs and sawdusts of oak and some other broadleaved tree species used. Recently oak trees have been substantially diminished due to extensive logging. Thus, to develop comparable synthetic formula using other tree species for the cultivation of Lentinus edodes, we investigated the effect of various nutrients and pretreatment on L. edodes mycelial growth in coniferous sawdusts(i.e., Pine and Larch). We found that 1.5 hr pretreatment of sawdust with hot water and adding 10% rice bran, 3% charcoal, 0.02% $NH_4CI$ and 0.5-1% lignosulfornic acid were effective for the growth of L. edodes in pine sawdust media. In larch sawdust pretreatment with acetone for one hr and adding 20% rice bran, 3% charcoal and 0.02% $NH_4CI$ increased L. edodes mycelial growth. We also analyzed the components of oak and coniferous sawdusts and found oak has higher content of xylose and lower content of lignin, arabinose and mannose than conifers. Rice bran, compared with BITEL(HOKKEN Co.) known for better commercial substitute for rice bran, has lower content of xylose and galactose, but the similar C/N ratio.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.3
• /
• pp.124-131
• /
• 2006

For commercialization of molten carbonate fuel cell (MCFC), it has some problems to be overcome such as decrease of porosity and thickness of the anode under the operating condition (at $650^{\circ}C$ and working pressure of more than 2 $kg_f/cm^2$). Recently, Ni-Al alloy anode has been proposed to replace the conventional Ni-Cr anode as an alternative material to resist a creep and inhibit the sintering. The objective of this research is to sinter the green sheet of Ni-Al alloy anode during single cell pre-treatment process, which has several advantages like cost down and simplification of manufacturing process. However, the Ni-Al alloy anode prepared with a conventional pre-treatment process showed the phase separation of Ni-Al alloy and formation of micropore(${\leqq}0.4{\mu}m$), resulting in low creep resistance and high electrolyte re-distribution. In order to prevent the Ni-Al alloy anode from phase-separating, nitrogen gas was used in the process of pre-treatment. Introducing the nitrogen, the phase separation from Ni-Al alloy into nickel and alumina was minimized and increased creep resistance. However, there was some micropore formation on the surface of Ni-Al alloy anode during the cell operation due to creation of lithium aluminate. Addition of more amount of electrolyte into a cell, especially at cathode, made the cell performance stable for 2,000 hrs. Consequently, it was possible to make the Ni-Al alloy anode with good creep resistance by the modified in-situ sintering technique.