• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.1
• /
• pp.25-31
• /
• 2023

In this study, the basic properties of CO₂ immobilized desulfurized gypsum (CFBG) and the possibility of being used as a stimulus for slag cement were reviewed, and performance evaluation was conducted through a concrete mixing test. The main components of CFBG were CaO and SO₃, and CaO and SO₃ increased as the drying temperature increased. The moisture content of undried CFBG was 15.7 %, the drying temperature was 1.7 % and the drying temperature was 0.03 % at 105 ℃. Mortar using CFBG tended to have a lower flow value as the drying temperature increased, and the compressive strength was equivalent to that of the FGB use mixture. As a result of the concrete experiment using CFBG SC, both slump and air volume satisfied the target range after 60 minutes, and the compressive strength tended to increase overall compared to the ternary binder mixture.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.552-559
• /
• 2023

The purpose of this study is to evaluate the crack reduction performance of blast furnace slag concrete mixed with expansive and swelling admixtures. As a basic performance test, various ingredients such as blast furnace slag fine powder (BFS), calcium sulfoaluminate (CSA), bentonite, and hydroxypropyl methyl cellulose (HPMC) were used, and the results showed that bentonite showed superior performance compared to HPMC. Afterwards, a MOCK-UP test was conducted to evaluate cracking and drying shrinkage according to the mixing ratio. As a result, when bentonite and a small amount of calcium phosphate were added, drying shrinkage was reduced and cracking was reduced. In particular, a cement mixture consisting of 30 % BFS, 1 % bentonite, and 1 % calcium phosphate showed optimal crack-free performance. It is believed that BFS concrete will contribute to compensating for shrinkage through continuous expansion activity and can be used for field applications.

• Clean Technology
• /
• v.19 no.1
• /
• pp.30-37
• /
• 2013

Low-rank coal with high water content (32.3 wt%) was dried by fry drying, and the fuel characteristics of the dried coal from which the oil was separated by using a high-speed centrifugal separator were analyzed. After fry drying for 6 min and 10 min, the water content decreased to 5.0 wt% and 4.2 wt% respectively. The higher calorific value (HCV) of the coal increased remarkably after fry drying, from 11,442.0 kJ/kg-wet. The oil content of the fry-dried coal was 15.0 wt% and it decreased with an increase in the reheating temperature: 9.7 wt% at $80^{\circ}C$ to 9.3 wt% at $100^{\circ}C$, and then to 8.5 wt% at $120^{\circ}C$. The recovered oil could then be reused. According to of thermogravimetric analysis (TGA), there was no difference in the weight loss patterns of the coal samples with different coal diameters at a reheating temperature of $120^{\circ}C$. This was because the amount of oil separated by the centrifugal separator was affected by the reheating temperature rather than the coal diameter. And derivative thermogravimetry (DTG) curves of raw coal before the fry-drying process, a peak is formed at $400^{\circ}C$ in which the volatile matter is gasified. In case of the fry-dried coal, the first peak is generated at $350^{\circ}C$, and the second peak is generated at $400^{\circ}C$. The first peak is caused by the oil that is replaced with the water contained in the coal during the fry-drying process. Further, the peaks of the coal samples in which the oil is separated at a reheating temperature of $80^{\circ}C$, $100^{\circ}C$, $120^{\circ}C$, respectively are smaller than that of the coal in which the oil is not separated, and this is caused by that the oil is separated by the centrifugal separator.

• Food Science and Preservation
• /
• v.24 no.3
• /
• pp.464-471
• /
• 2017

The purpose of this study was to evaluate the effect of superheated steam drying on physicochemical and microbial characteristics of Korean traditional actinidia (Actinidia arguta) leaves. Actinidia leaves were dried at steam temperature of $350^{\circ}C$ and oven temperature of $150^{\circ}C$ for 40-200 sec. Moisture content and water activity decreased with increasing the drying time, while color values including L, a, and b values and total color difference (${\Delta}E$) increased as drying time increased. The relationship between moisture content and water activity showed an exponential fit with high correlation vlaue ($R^2=0.9909$). Total phenolics and flavonoids content and antioxidant activity such as DPPH radical scavenging activity, ABTS radical scavenging activity, and FRAP assay of dried actinidia leaves increased with increasing the drying time up to 160 sec, but dramatically decreased at drying of 200 sec. The numbers of total areobic bacteria of leaves was not detected at drying time over 120 sec and coliform of all the samples was not detected. As a results, the superheated steam was an very effective drying method of increase to the nutritional and sanitary quality of dried Korean traditional actinidia leaves.

• Applied Chemistry for Engineering
• /
• v.22 no.5
• /
• pp.532-539
• /
• 2011

The physical and chemical properties of the dried low rank coals (LRCs) before and after the surface treatment using ozone and ammonia were characterized in this study. The contents of moisture, volatiles, fixed carbon and ash consisting of dried LRCs before the surface treatment were about 2.0, 44.8, 44.9 and 8.9%, respectively. Also, it was composed of carbon of 62.66%, hydrogen of 4.33%, nitrogen of 0.94%, oxygen of 27.01% and sulfur of 0.09%. The dried LRCs was surface-treated with the various dry methods using gases such as ozone at room temperature, ammonia at $200^{\circ}C$ and then the dried LRCs before and after the surface treatment were characterized by the various analysis methods such as FT-IR, TGA, proximate and elemental analysis, caloric value, ignition test, adsorption of $H_2O$ and $NH_3-TPD$. As a result, the oxygen content increased and the calorific value, ignition temperature and the contents of carbon and hydrogen relatively decreased because the oxygen-contained functional groups were additionally generated by the surface oxidation with ozone which plays a role as an oxidant. Also, its $H_2O$ adsorption ability got higher because the hydrophilic oxygen-contained functional groups were additionally generated by the surface oxidation with ozone. On the other hand, it was confirmed that the dried LRCs after the surface treatment with $NH_3$ at $200^{\circ}C$ have the decreased oxygen content, but the increased calorific value, ignition temperature and contents of carbon and hydrogen because of the decomposition of oxygen-contained functional groups the on the surface. In addition, the $H_2O$ adsorption ability was lowered bucause the surface of the dried LRCs might be hydrophobicized by the loss of the hydrophilic oxygen-contained functional groups. It was concluded that the various physico-chemical properties of the dried LRCs can be changed by the surface treatment.

• The Science & Technology
• /
• v.29 no.11 s.330
• /
• pp.22-23
• /
• 1996

고교시절 딱딱한 자연과학분야가 싫어 수업시간에 소설책만 읽었던 나는 대학 때 영문학을 공부하여 문학활동을 하면서 우연히 과학잡지와 인연을 맺었다. 그후 나는 무미건조하고 난해한 과학원고를 다듬어 다시 쓰는 일을 계속했다. 그무렵 나는 우리나라 과학기술수준을 높이려면 우선 젊은 세대들이 과학에 흥미를 갖도록 하고 그러려면 전문지식을 알기 쉽고 재미있게 소개하는 전문가와 매체가 있어야겠다고 생각해 SF작가 클럽 등을 결성, 동호인들과 활동을 했는데 지금은 큰 보람을 느낀다.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.19-25
• /
• 2004

This study was carried out to investigate a radial distribution of moisture contents (MCs) within a log cross section (LC) during oven-drying of 3 mm-thick circumferential slices cut from several domestic softwoods LCs.For Korean red pine, drying rate of sapwood slices during oven-drying represented much higher values than that of heartwood slices, and so sapwood with higher green MC early reached below fiber saturation point (FSP) rather than heartwood did. However, this distribution of moistures did not last for long duration. For Japanese larch, green MC of sapwood was approximately three times higher than that of heartwood. This similar distribution in MC was lasted until about 20% average MC. The MC was around uniform throughout the sapwood of Ginkgo when green and during oven-drying, although it was somewhat fluctuated. For Japanese cedar, the heartwood with so low moistures around FSP would begin to shrink from the beginning stage of drying, but the sapwood above hygroscopic MC prevents the heartwood from shrinking, and consequently, the heartwood or the transition wood goes into tension stress. The results for Japanese cypress showed that the green MCs of the sapwoods were much lower than those for heartwoods, and then this trend was continued until about 20% in average MC. For Chinese thuja, the green MCs of sapwoods were about 2 times as high as those of heartwood, but this along the radial gradient in MC rapidly became gentle during oven-drying.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.3
• /
• pp.131-136
• /
• 1990

여러해 전부터 선박의 생산실적이나 생산성 관련 자료를 기록하고 보완하는 작업을 꾸준히 개선토록 노력해온 결과중 중요한 것 하나는, 선박의 여러 가지 설계 검토과정에서 충분히 활용할 수 있는 함축성 있고 믿을만한 형태의 생산정보를 제공해줄 수 있게 되었다는 것이라고 말 할 수 있겠다. 이러한 자료들은 생산계획상 각 단계(stage)에서의 작업량, 예상재료비와 인건비의 산출등이 포함될 수 있으며, 선박이나 해상구조물의 전반적인 설계방법론(design methodology)을 개선코자 한다면 ''생산지향적 설계(Design for Production)''의 근간이 되는 선박건조전략(build strategy), 구매정책(purchasing policy)과 생산기술(production technology)에 대한 폭넓은 지식이 한데 어우러져야 한다. 최근에는 CIMS의 일부분에서 보는 바와 같은 경영관리, 설계 및 생산지원 시스템의 도입으로 이와 같은 설계 프로세스의 추진을 가능케하고 있다. 이와 병행하여 설계를 지원하기 위한 전산기술, 특히 대화형 화상처리기술(interactive graphics)의 발달은 설계자가 선박의 형상이나 구조 배치를 여러 가지로 변화시켜 가면서 눈으로 즉시 확인할 수 있도록 설계자의 능력을 배가시키는데 크게 기여하고 있다. 여러 가지의 설계안(alternative design arrangement)을 신속히 만들어내고 이를 즉시 검토 평가할 수 있는 능력을 초기설계 단계에서 가질 수 있다면 이는 분명히 큰 장점일 것이며, 더구나 설계초기 단계에 생산관련인자를 설계에서 고려할 수 있다면 이는 더욱 두드러진 발전일 것이다. 생산공법과 관련생산 비용을 정확히 반영한 각 가지의 설계안을 짧은 시간내에 검토하고 생산소요 비용을 산출하여 비교함으로써, 수주계약단계에서 실제적인 생산공법과 신뢰성있는 생산실적자료를 기준으로 하여 총 건조비(total production cost)를 최소로 하는 최적의 설계를 선택할 수 있도록 해 줄 것이다. 이제 이와 같은 새로운 설계도구(design tool)를 제공해 주므로써 초기설계에 각종 생산관련 정보나 지식 및 실적자료가 반영가능토록 발전되었다. 본 논문은 영국의 뉴카슬대학교(Univ. of Newcastle upon Type)에서 위에 언급한 특징들을 반영하여 새로운 선박구조 설계 방법을 개발한 연구결과를 보여주고 있다. 본 선계연구는 5단계로 구분되는데; (1) 컴퓨터 그라픽스를 이용하고 생산정보 데이타베이스와 연결시켜 구조형상(geometry)을 정의하고 구조부재 칫수(scantling) 계산/결정 (2) 블럭 분할(block division) 및 강재 배치(panel arrangement)의 확정을 위해 생산기술 및 건조방식에 대한 정보 제공 (3) 상기 (1) 및 (2)를 활용하여 아래 각 생산 단계에서의 생산작업 분석(work content assessment) a) 생산 준비 단계(Preparation) b) 가공 조립 단계(Fabrication/Assembly) c) 탑재 단계(Erection) (4) 각각의 설계(안)에 대하여 재료비(material cost), 인건비(labour cost) 및 오버헤드 비용(overhead cost)을 산출키 위한 조선소의 생산시설 및 각종 품셈 정보 (5) 총 건조 비용(total production cost)을 산출하여 각각의 설계안을 비교 검토. 본 설계 방식을 산적화물선(Bulk Carrier) 설계에 적용하여 구조배치(structural geometry), 표준화의 정도(levels of standardisation), 구조생산공법(structural topology) 등의 변화에 따른 설계 결과의 민감도를 분석(sensitivity studies)하였다. 전산장비는 설계자의 대화형 접근을 용이하도록 하기 위해 VAX의 화상 처리장치를 이용하여 각 설계안에 대한 구조형상과 작업분석, 건조비 현황 등을 제시할 수 있도록 하였다. 결론적으로 본 연구는 설계초기 단계에서 상세한 건조비 모델(detailed production cost model)을 대화형 화상 처리방법에 접합시켜 이를 이용하여 여러가지 설계안의 도출과 비교검토를 신속히 처리할 수 있도록 함은 물론, 각종 생산 실적정보를 초기설계에 반영하는 최초의 시도라고 믿으며, 생산지향적(Design for Production) 최적설계분야의 발전에 많은 도움이 되기를 기대해 마지 않는다. 참고로 본 시스템의 설계 적용결과를 부록에 요약 소개하며, 상세한 내용은 참고문헌 [4] 또는 [7]을 참조 요망한다.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.670-678
• /
• 2003

Recently, since industrial waste and life waste leaped into a pollution source, the building material used now a days is striking the limit. The purpose of this paper is to investigate an application of recycled coal ash using non-sintering method in the construction field. Accordingly, compressive strength, elastic modulus and drying shrinkage were experimentally studied for hardened coal ash using the non-sintering method. Also, Lineweaver and Burk method were applied to the regression analysis of drying shrinkage for the proposal equation. Elastic modulus, compressive strength of material become the basis properties of structural design. And these properties by age for hardened coal ash are important because of change by pozzolan reaction. This hardened coal ash is weak for tensile stress like that of concrete. And drying shrinkage is very important factor to make huge tensile force in early age. In the results, although some differences were shown when comparing coal ash with mortar or concrete, the application as a building material turned out to be possible if further researches were carried out. And the shrinkage characteristic of hardened coal-ash reveals to be similar to that of moderate heat cement.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.4
• /
• pp.591-598
• /
• 2002

In the ship structural design, the material cost of hull weight and the overall cost of construction processes should be minimized considering safety and reliability. In the past, minimum weight design has been mainly focused on reducing material cost and increasing dead weight reflect the interests of a ship's owner. But, in the past experience, the minimum weight design has been inevitably lead to increasing the construction cost. Therefore, it is necessary that the designer of ship structure should consider both structural weight and construction cost. In this point of view, multi-objective optimization technique is proposed to design the ship structure in this study. According to the proposed algorithm, the results of optimization were compared to the structural design of actual VLCC(Very Large Crude Oil Carrier). Objective functions were weight cost and construction cost of VLCC, and ES(Evolution Strategies), one of the stochastic search methods, was used as an optimization solver. For the scantlings of members and the estimations of objectives, classification rule was adopted for the longitudinal members, and the direct calculation method, GSDM(Generalized Slope Deflection Method), lot the transverse members. To choose the most economical design point among the results of Pareto optimal set, RFR(Required Freight Rate) was evaluated for each Pareto point, and compared to actual ship.