• The KIPS Transactions:PartC
• /
• v.15C no.1
• /
• pp.31-36
• /
• 2008

The clock frequency difference of sensor nodes is one of main parameters in TOF estimation and affect to degrade ranging algorithms to estimate positions of mobile nodes in wireless sensor networks. The specification of IEEE802.15.4a describes asynchronous TWR and SDS-TWR insensitive to frequency difference without any additional network synchronization. But the TWR and SDS-TWR can not eliminate sufficiently the effect of frequency difference of node pair, packet processing delay and its difference. Especially use of low cost oscillator with wide range offset, sensor node with different hardware and software can make the positioning errors worse. We propose an estimation method of frequency differences, and apply the measured frequency differences to TWR and SDS-TWR. We evaluate the performance of the proposed algorithm with simulation, and make certain that the proposed method enhances the performance of existing algorithms with positioning errors less than 25 cm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.532-539
• /
• 2018

A position estimation technique is presented for a missile using high-resolution range profiles obtained by three wideband radars. Radar measures a target range using a reflected signal from the surface of a missile. However, it is difficult to obtain the range between the radar and the origin of the missile. For this reason, the interior angle between the moving missile and tracking radar is calculated, and a compensated range between surface of the missile and its origin is added to the tracking range of the radar. Therefore, position estimation of a missile can be achieved by using three total ranges from each radar to the origin of the missile. To verify the position estimation of the missile, electromagnetic numerical analysis software was used to prove the compensated range according to the flight position. Moreover, a wideband radar operating at 500-MHz bandwidth was applied, and its range profile was used for the position estimation of a missile.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.4
• /
• pp.166-172
• /
• 2007

In this paper, we address the target positioning performance of Multi-Static sonar with respect to target positioning method and measurement error. Based on the analysis on two candidate solution approaches, namely, Least Square (LS) using range and angular information simultaneously and Maximum Likelihood (ML) using only range information as the existing information fusion methods for possible application to Multi-Static sonar, we propose to employ ML using range and angular information. Assuming that each sensor can receive range and angular information, we conduct representative comparison experiments over the existing and proposed methods under various measurement noise scenarios. We also investigate the target positioning performance according to number of sensors, distance between transmitter and receiver. According to the experimental results, RMSE of the proposed ML with distance and direction information is found to be more superior to ML using distance alone and to LS in case distance between transmitter and receiver is longer and number of receiver is smaller.

• Proceedings of the Korea Contents Association Conference
• /
• 2012.05a
• /
• pp.33-34
• /
• 2012

무선 센서 네트워크의 다양한 응용에 있어 센서 노드의 지리학적 위치 측정은 매우 중요하다. 이를 위해 비-거리(Range-Free) 기반 위치 측정 기법에 대한 연구가 활발하게 진행 중이며, 비 균일 네트워크 환경에서 위치 정확도를 향상하기 위한 밀집 확률 기반의 위치 측정 기법이 제안되었다. 밀집 확률 기반의 위치 측정 기법에서 추정 거리 산출 시 노드 통신 반경 내 1-홉 거리는 모두 동일한 값을 갖는데 이는 반경 내 가까운 이웃 노드와 먼 이웃 노드가 있어도 모두 같은 거리로 추정하기 때문에 위치 측정 시 오차가 발생 할 수 있다. 따라서 본 논문에서는 이러한 오차를 줄이기 위해 각 노드마다 거리 추정 후 센싱 반경을 조절하여 2차 지역 거리 평가를 통해 센서의 위치를 측정하는 기법을 제안한다. 성능평가 결과, 제안하는 기법이 기존 기법에 비해 측위 정확도가 크게 향상되었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.357-358
• /
• 2018

The track radar use the range track loop to track the target range. The bandwidth of the radar range tracker can be determined by tradeoff according to signal to noise ratio and the target range. On the other hand, electronic warfare is carried out to prevent the radar from tracking targets by electronic attack. The deception or noise jamming in electronic warfare can be performed to interfere with the range track loop of the radar. In order to efficiently perform electronic warfare, the bandwidth in radar tracking loop is estimated and can be used for electronic attack. To do this, we have studied the method of estimating the bandwidth of radar tracking loop using the variables that can be gathered in electronic warfare.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.2
• /
• pp.130-136
• /
• 2012

In this paper, we propose a near-field range estimation method for a uniform linear array that can calibrate bearing estimation error which give a bad influence on a range estimation process. When a range is fixed, the bearing error is calibrated to maximize the beamformer output by the proposed algorithm based on the gradient method. Simulation results show that the proposed algorithm can compensate the bearing error which is less than the mainlobe beamwidth so that reduce the range estimation error as similar as the case of no bearing error.

• Journal of the Institute of Convergence Signal Processing
• /
• v.18 no.1
• /
• pp.21-24
• /
• 2017

Passive millimeter wave (MMW) imaging penetrates clothing to detect concealed objects. The distances extraction to the concealed objects is critical for the security and defense. In this paper, we address a passive stereo 3 mm MMW imaging system to extract the longitudinal distance to the concealed object. The concealed object area is segmented and extracted by the k-means clustering algorithm with splitting initialization. The distance to the concealed object is estimated by the corresponding centers of the segmented objects. In the experimental two pairs (each pair for horizontal and vertical polarization) of stereo MMW images are obtained to estimate distances to concealed objects.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.228-231
• /
• 1999

3차원 공간상의 표적의 위치는 방위각, 고각, 거리의 세가지요소로 나타내어 질 수 있다. 이 논문에서는 등각적 선배열 센서로 이루어진 3개의 부분센서배열을 이용한 3차원 표적의 위치추정 알고리듬을 제안하였다. 원거리 표적의 방위각 추정 알고리듬으로 근거리 표적의 방위각을 추정하면 추정된 방위각은 실제 근거리 표적의 방위각과 고각과 거리의 비선형 대수적 관계식으로 주어진다. 제안한 알고리듬은 3개의 부분센서배열에서 각각 표적을 원거리에 있다고 가정하고 원거리입체각을 추정하여 위의 대수적 관계식을 얻은 후 이들 관계식을 연립하여 실제 근거리 표적의 위치를 추정하였다. 다중표적의 경우 각각의 부분센서배열에서 추정한 원거리입체각이 어떤 표적에 대한 추정치인지 연관시켜주는 알고리듬이 필요하다. 이 논문에서는 추정한 원거리입체각의 모든 조합으로부터 3차원 MUSIC 스펙트럼값을 비교하여 그 중 표적의 개수만큼을 선별하여 다중표적의 위치를 추정하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.6
• /
• pp.527-532
• /
• 2013

Depth estimation is an essential factor for robot vision, 3D scene modeling, and motion control. The depth estimation method is based on focusing values calculated in a series of images by a single camera at different distance between lens and object. In this paper, we proposed a relative depth estimation method using focus measure. The proposed method is implemented by focus value calculated for each image obtained at different lens position and then depth is finally estimated by considering relative distance of two patterns. We performed various experiments on the effective focus measures for depth estimation by using various patterns and their usefulness.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.245-246
• /
• 2008

변전소 모선에서 측정되는 전압, 전류를 기반으로 하는 CB기반 고장거리 추정기법은 배전선의 다중 분기선 때문에 다중개의 고장위치를 추론하는 것은 물론 분기 부하모델의 불확실성으로 인해 거리 계산에 오차를 포함하게 된다. 따라서 본 연구에서는 유비쿼터스 기반의 배전계통 하에서 구간 측정 전압, 전류 및 IED간 정보교환을 통해 얻어지는 전압, 전류 정보를 이용하여 고장경로를 추정하는 IED 기반 고장경로 추정기법을 제안한다.