• Journal of Korean Association for Spatial Structures
• /
• v.18 no.1
• /
• pp.45-53
• /
• 2018

Following the earthquake that shook the city of Gyeongju, Korea, in 2016, it became apparent that research on the safety of cultural heritages against the seismic hazards is necessary in Korea. Predictions of how historically significant stone pagodas would behave the earthquakes anticipated in near future, which are the subject of this study, is also required. In this study, the dynamic characteristics of 15 cultural heritage designated stone pagodas of Korea were investigated, including natural frequency and damping ratio, and the stiffness of the stone material and its contact area were determined using eigenvalue analysis by assuming the stone pagodas to be multi-degree-of-freedom structures. The results of this study enable the structural modeling of stone pagodas using a finite element analysis program and the method is expected to be useful in assessing the structural safety of stone pagodas against vertical loads as well as lateral forces, including earthquakes. Also, by identifying the dynamic characteristics of the structures, the results of this study can be utilized as a nondestructive testing method to determine the rigidity of cultural heritage structures and to identify inherent problems. The natural frequencies of the Korean stone pagodas were measured to be within 3.5~8.3Hz, excluding cases with distinct natural frequency results, and it was determined that the natural frequencies of the stone pagodas are influenced by various parameters including the height and joint stiffness of the structures.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.4
• /
• pp.15-22
• /
• 2002

In the course of seismic probabilistic risk assessment(SPRA), seismic fragility analysis(SFA) is utilized as a tool to evaluate the actual seismic capacity of structures. This paper introduces a methodology of SFA and its evaluation procedures, especially focusing on the basic fragility variables. A new definition of the response spectrum shape factor as one of the most critical basic variables is suggested. The new factor is expressed as a term of linear algebraic sum using the modal contribution factor. The efficiency of new response spectrum shape factor is evaluated and validated to use in practice through the case study of the nuclear power plant structures. The case study results show that the proposed method can be effectively applicable to multi-mode structures with composite modal damping.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.1
• /
• pp.1-10
• /
• 1998

In the dynamic soil-structure interaction(SSI) analysis, numerous uncertain parameters are involved. They include the uncertainties in the definition of input motions, modeling of soil-structure interaction systems. analysis techniques, etc. This paper presents the results of parametric studies of the seismic responses of a reactor containment structure built on the viscoelastic layered soil. Among the numerous parameter, this study concentrates on the effects of definition point of the input motion, embedment of structure to the base soil, thickness of the top soil layer, and rigidity of the base soil. The substructure method using frequency independent impedances is adopted. The method is based on the mode superposition method in time domain using the composite modal damping values of th SSI system computed from the ratio of dissipated energy to the strain energy for each model. From the study results, the sensitivity of each parameter on the earthquake responses has been suggested for the practical application of the substructure method of SSI analysis.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.3
• /
• pp.41-46
• /
• 2001

The very large vessels like VLCC and container ship have been built recently and those vessels have smaller structural strength in comparison with the other convectional skips. As a result the fatigue destruction of upper deck occurs a frequently due to the springing phenomenon at the encountering frequencies. In this study, the hydrodynamic loads are calculated by three-dimensional source distribution method with the translating and pulsating Green function. A ship is longitudinally divided into 23 sections and the added mass, damping and hydrodynamic force of each section is calculated. focusing only on the vertical motion. Stiffness matrix is calculated by the Euler beam theory. The calculation is carried out for Esso Osaka.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.6
• /
• pp.301-308
• /
• 2018

This paper presents an optimal design method of a hybrid structural control system considering multi-hazard. Unlike a typical structural control system in which one system is designed for one specific type of hazard, a simultaneous optimal design method for both active and passive control systems is proposed for the mitigation of seismic and wind induced vibration responses of structures. As a numerical example, an optimal design problem is illustrated for a hybrid mass damper(HMD) and 30 viscous dampers which are installed on a 30 story building structure. In order to solve the optimization problem, a self-adaptive Harmony Search(HS) algorithm is adopted. Harmony Search algorithm is one of the meta-heuristic evolutionary methods for the global optimization, which mimics the human player's tuning process of musical instruments. A self-adaptive, dynamic parameter adjustment algorithm is also utilized for the purpose of broad search and fast convergence. The optimization results shows that the performance and effectiveness of the proposed system is superior with respect to a reference hybrid system in which the active and passive systems are independently optimized.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.4
• /
• pp.205-213
• /
• 2019

In the Pohang Earthquake in 2017, considerable damage to non-structural elements, such as ceiling systems, exterior finishes, and curtain walls, was reported; thus, the seismic designs of non-structural elements are important. In this study, the modal characteristics of a ceiling system were investigated through the impact hammer test. The frequency and damping ratio according to the length of the hanger bolt were identified. In addition, collision experiments were conducted to obtain the impact duration for exactly considering the impact effects of the ceiling against a wall or other adjacent elements. Based on the identified dynamics and impact duration of the ceiling system, the seismic responses of the ceiling system were obtained numerically in case of collision. Numerical simulation results show that the impact load tends to increase with the clearance between the ceiling and adjacent elements, and is not correlated with the length of the hanger bolt.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.371-382
• /
• 2006

A buffeting analysis is utilized for the estimation of aerodynamic vulnerability of a cable-stayed bridge due to upcoming wind turbulences. The buffeting analysis requires several input parameters such as structural parameters, aerodynamic parameters, and aero-elastic parameters. This study is motivated to estimate the sensitivity of these parameters on buffeting responses. The Seohae bridge is selected as an example bridge. The investigated parameters consist of the inclination of lift and drag coefficient of stiffening girder section, exponential decay factors of span-wise distributed wind turbulences, roughness length, spectra of wind velocity fluctuation, and structural damping. The buffeting response showed high dependency on the input parameters. As conclusions, the importance of parameter selection is emphasized. A further study is also proposed for more general conclusions.

• Tunnel and Underground Space
• /
• v.19 no.5
• /
• pp.432-439
• /
• 2009

For more reliable estimation of seismic source, attenuation properties and dynamic ground property, site amplification function should be considered. Among various estimation methods, this study used the Nakamura's method (1989) for estimating site amplification characteristics. This method was originally applied to the surface waves of background noise and therefore there are some limitations in applying to general wave energy. However, recently this method has been extended and applied to the S wave energy successfully. This study applied the method to S wave and Coda wave energy, which is equivalent to the backscattered S wave energy. We used more than 60 observed ground motions from 5 earthquakes which were occurred recently, with magnitude range from 3.6 to 5.1. Each station showed characteristic site amplification property in low-, high- and resonance frequencies. Some of the stations showed as high as 4 times of site amplification in the range of specific frequencies, which may imply abnormal small scale geologic strata below the station or development of various trapped modes in the basin structure. Moreover, removal of site amplification can give us more reliable seismic source and attenuation parameters, addition to the seismic hazard estimation.

• Journal of Sensor Science and Technology
• /
• v.5 no.5
• /
• pp.21-29
• /
• 1996

A piezoresistive silicon acceleration sensor with 8 beams, utilized by an unique silicon micromachining technique using porous silicon etching method which was fabricated on the selectively diffused (111)-oriented $n/n^{+}/n$ silicon subtrates. The width, length, and thickness of the beam was $100\;{\mu}m$, $500\;{\mu}m$, and $7\;{\mu}m$, respectively, and the diameter of the mass paddle (the region suspended by the eight beams) was 1.4 mm. The seismic mass on the mass paddle was formed about 2 mg so as to measure accelerations of the range of 50g for automotive applications. For the formation of the mass, the solder mass was loaded on the mass paddle by dispensing Pb/Sn/Ag solder paste. After the solder paste is deposited, Heat treatment was carried out on the 3-zone reflow equipment. The decay time of the output signal to impulse excitation of the fabricated sensor was observed for approximately 30 ms. The sensitivity measured through summing circuit was 2.9 mV/g and the nonlinearity of the sensor was less than 2% of the full scale output. The output deviation of each bridge was ${\pm}4%$. The cross-axis sensitivity was within 4% and the resonant frequency was found to be 2.15 KHz from the FEM simulation results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.10a
• /
• pp.319-323
• /
• 1996

\ulcorner\ulcorner\ulcorner\ulcorner 80,000 rpm \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner(ultra-centrifuge)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner(critical speed)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner(separation margin)\ulcorner \ulcorner\ulcorner, \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner-\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner, \ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner(extra slender shaft)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner, \ulcorner\ulcorner 1\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner(bumper ring) \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner(guide bearing)\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner. \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner(finite element method)\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner, \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner\ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner \ulcorner\ulcorner\ulcorner \ulcorner\ulcorner(damping)\ulcorner \ulcorner\ulcorner\ulcorner\ulcorner.