• Korean Journal of Materials Research
• /
• v.8 no.9
• /
• pp.871-875
• /
• 1998

High aspect ratio microstructures were fabricated by photolithography. The material for the microstructure was photosensitive glass which has good mechanical and electrical insulation properties. The photosensitive glass was exposed to ultraviolet light at 312nm through a chromium mask in which the structures are drawn. After heat treatment process over $500^{\circ}C$, the photosensitive glass was etched in a 10% hydrofluoric acid solution with ultrasonic conditions. Final dimension of the micro-framework was greatly dependent on the thickness of photosensitive glass, mask pattern, ultraviolet light exposure and etching conditions. The maximum aspect ratio of the micro-framework obtained from this work was over 30.

• Journal of the Korean Ceramic Society
• /
• v.41 no.11
• /
• pp.826-833
• /
• 2004

In this study, photosensitivity dynamics in SiO$_2$ glass with the composition similar to that of silica Planar Lightwave Circuit (PLC) devices was investigated as a fundamental study prior to the device fabrication. Silica bulk glasses with similar composition to the core layer of PLC devices were prepared with variable composition of B$_2$O$_3$. The photosensitivity in boron and germanium co-doped SiO$_2$ glass yields refractive index change $\Delta$n as high as 10$\^$-3/. However such index modulation disappeared after annealing. From the result of annealing experiment and W absorption / Raman spectra, we conclude the compaction model is applicable to our glass system.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.124.2-124
• /
• 2000

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2004.05a
• /
• pp.66-66
• /
• 2004

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.144.2-144
• /
• 2003

• Laser Solutions
• /
• v.14 no.1
• /
• pp.25-29
• /
• 2011

Micromachining of photosensitive glass by UV exposure, heat treatment, and etching processes is reported. Like photoresist, the photosensitive glass is also classified into positive and negative types by development characteristics. For the positive type, the exposed area is crystallized and etched away during the etching process in HF solution, whereas the unexposed area is crystallized and etched away for the negative type. The crystallized area of the photosensitive glass has an etch rate approximately 30~100 times faster than that of the amorphous area so that it becomes possible to fabricate microstructures in the glass. Based on the unique properties of glass such as high optical transparency, electrical insulation, and chemical/thermal stability, the glass micromachining technique introduced in this work could be widely applied to various devices in the fields of electronics, bio engineering, nanoelectonics and so on.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1114-1118
• /
• 1999

Barrier rib for the plasma display panel(PDP) was made by photolithographic process utilizing photosensitive barrier rib paste. The barrier rib paste was prepared by first dissolving ethylcellulose(binder polymer) in butyl carbitol(BC)/butyl carbitol acetate(BCA) =30/70 wt % mixture solvent at 15 wt % concentration. To this solution a mixture of functional monomers consisted of tripropyleneglycol diacrylate/ pentaerythritol triacrylate = 50/50 wt %, Irgacur 651 photoinitiator, and barrier rib powder were added and then the whole mixture was mixed in the three roll mill for 2 hr. The effect of component and concentration of photosensitive barrier paste on the photolithographic process was studied. After optimization of the paste formulation and photolithographic process, barrier rib could be obtained with good resolution up to $100{\mu}m$ height.

• Applied Chemistry for Engineering
• /
• v.5 no.4
• /
• pp.662-668
• /
• 1994

The cinnamoyl esters of polyresorcinol-formaldehyde glycidyl ether (RGEFC) with photosensitive functional group were prepared. Photosensitivity of RGEFC were investigated by the change of solubility before and after exposure to light. Various samples coated on glass plates were exposed to light under various conditions and steeped in the same solvent as used for coating, and then the yield of residual film was calculated. The yield of the residual film which was closely related to the sensitivity of the film, was affected by the degree of polymerization of the backbone resin, sensitizers and their concentration. The sensitivity was depended upon the degree of polymerization. Most effective sensititizer for RGEFC among the sensitizers used was 2,6-dichloro-4-nitroaniline.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.1-6
• /
• 2002

Micro engine that includes Micro scale combustor is fabricated. Design target was focused on the observation of combustion driven actuation in MEMS scale. Combustor design parameters are somewhat less than the size recommended by feasibility test. The engine structure is fabricated by isotropic etching of the photosensitive glass wafers. Electrode is formed by electroplating of the Nickel. Photosensitive glass can be etched isotropically with almost vertical angle. Bonding and assembly of structured photosensitive glass wafer from the engine. Combustor size was determined to be 1mn scale. Piston in cylinder moves by fuel injection and reaction. In firing test, adequate engine operation including ignition, flame propagation and piston motion was observed. Present study warrants further application research on MEMS scale internal combustion power units.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.87-93
• /
• 2011

We developed a fluorene-containing multifunctional binder polymer for LCD color filter resist, and employing the binder polymer, carbon black based black photoresist (CBR) was prepared in order to apply it to the black matrix (BM). To obtain the multifunction of the binder polymer, we synthesized bisphenol fluorene epoxy acrylate-containing unsaturated polyester and identified the binder polymer structure with $^1H$ NMR, GPC and FTIR. The corresponding BFEA-polyester binder polymer was compared with the commercially available acryl binder toward the application to the CBR. From the BM lithography test, we found that the synthesized BFEA-polyester binder had better photocrosslinking capability and alkali solubility. In addition, the newly developed binder gave a good process margin, good resolution and adhesion property on a glass substrate.