• Journal of the Korean Society of Propulsion Engineers
• /
• 제19권2호
• /
• pp.38-45
• /
• 2015

This paper describes an ejector design technique which used for simulating low pressure environment corresponding to high altitude. Also the ejector performance characteristics was investigated according to performance and geometric variables by cold gas flow test. Entrainment ratio, compression ratio and expansion ratio were designated as performance variables and an ejector gap ratio was designated as a geometric variable. A relationship between the performance variables to predict the ejector performance was identified and it was confirmed that the performance variables have much more effective than the ejector gap ratio through the ejector cold gas flow test.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제23권7호
• /
• pp.104-112
• /
• 2019

The material properties of the 3D printing cement composite mortar were evaluated, and the performance range in which printing was possible was calculated using the void ratio in a fresh state as a single index. As a results of the tests, as the water-binder ratio (W/B) increased, the mortar flow value increased and the density and strength decreased. As the sand-binder ratio (SS/B) increased, the mortar flow value decreased. However, strength and density increased and decreased up to a certain SS/B. As admixture-binder ratio (Ad/B) increased, mortar flow value, density, and strength decreased. These trends make it difficult to mix-design to meet the target performances of 3D printing mortars, represented by extrudability and buildability. The value of mortar flow increased proportionally with the void ratio, while the density and strength apparently decreased as the void ratio increased. This indicates that void ratio can be utilized as a single index for controlling the material properties in the design of mortar mixtures. It was found that mortar mixture could be printed by a 3D printer when the void ratio was in the range from 0.6 to 0.7. This was verified by printing a mortar which has the void ratio of 0.634. The mortar was produced with the mixture design of W/B 35.0%, SS/B 60.0%, and Ad/B 0.1%. Further research applying diverse admixtures is needed to improve the quality of 3D printing output mortars.

• Journal of the Korean Geotechnical Society
• /
• 제23권10호
• /
• pp.47-56
• /
• 2007

In this research, the effects of the gravel content on the liquefaction behavior for both of the isotropically and $K_0-anisotropically$ consolidated gravel-sand mixtures are investigated. for this purpose, the cyclic triaxial tests for the specimens with the same relative density (Dr=40%) and variations of gravel content were performed. On the other hand, a series of undrained cyclic triaxial tests were carried out on the isotropically consolidated gravel-sand mixtures with the same void ratio (e=0.7) and from 0% to 30% gravel contents. Void ratios of gravel-sand mixtures with the same relative density (Dr=40%) are found to decrease significantly with the increase of the gravel content from 0% to about 70% and increase thereafter. But the void ratio of the sand matrix among the gravel skeleton increases with the increase of the gravel contents. Test results are as follows : for the isotropically consolidated specimen with 40% of relative density and low gavel contents (GC=0%, 20%, 40%), pore water pressure development and axial strain behavior during undrained cyclic loading show similar behavior to those of the loose sand because of high void ratio, and the specimens with high gravel content (70%) both pore pressure and strata behaviors are similar to those of dense sand. And the isotropically consolidated specimens with the same void ratio (e=0.7) and higher gravel contents show the same behavior of pore water pressure and axial strain as that of the loose sand, but for the lower gravel content this behavior shows similar behavior to that of dense sand. The liquefaction strength of the isotropically consolidated specimens with the same relative density increases with gravel content up to 70%, and the strength decreases with the increase of the gravel content at the same void ratio. Thus, it is confirmed that the liquefaction strength of the gravel-sand mixtures depends both on relative density and void ratio of the whole mixture rather than the relative density of the sand matrix filled among gravels. On the other hand, the behavior of pore water pressure and axial strain for the $K_0-anisotropically$ consolidated gravel-sand mixtures shows almost the same cyclic behavior of the sand with no stress reversal even with some stress reversal of the cyclic loading. Namely, even the stress reversal of about 10% of cyclic stress amplitude, the permanent strain with small cyclic strain increases rapidly with the number of cycles, and the initial liquefaction does not occur always with less than maximum pore water pressure ratio of 1.0. The liquefaction resistance increases with the gravel contents between 0% and 40%, but tends to decrease beyond 40% of gravel content. In conclusion, the cyclic behavior of gravel-sand mixtures depends on factors such as gravel content, void ratio, relative density and consolidation condition.

• Journal of the Korean Geotechnical Society
• /
• 제24권11호
• /
• pp.79-89
• /
• 2008

In this study, a series of undrained cyclic triaxial tests were performed with three different consolidation stress ratios ($K_c$=1.0, 1.5, 2.0) to investigate the undrained shear strength characteristics of sands with respect to the amount of contained silt located around the basin of Nak-dong River. The test results show that the more the sand has silt, the lower is cyclic shear stress ratio (CSR) in all $K_c$ and that the higher $K_c$ goes, the larger CSR decreases due to the increase of contained silt. The excessive pore pressure caused during shearing has an influence on the decrease of CSR by the high initial pore pressure in proportion to the amount of contained silt regardless of the $K_c$ value. After consolidation, the analysis of the skeleton void ratio of the sample reveals that the main cause of the decrease of CSR as well as the increase of the initial excessive pore pressure is the increase of the skeleton void ratio in proportion to the amount of contained silt.

• The Journal of Engineering Geology
• /
• 제15권2호
• /
• pp.123-132
• /
• 2005

This study presents the results of a laboratory investigation performed to study physical properties of soil-bentonite mixtures through the vertical permeation test and dielectric measurement test using Frequency Domain Reflectometry system for the liner of waste landfill. For the laboratory experiments, geotechnical testing was conducted on pre-mixed soil-bentonite which is consisted of standard sand, weathered granite soil and bentonite for estimating physical parameters such as a volumetric water content, void ratio and dielectric constant. In experiment results, initial soil-bentonite mixing rate has an effect of change of volumetric water content. Also change of volumetric water content of a soil-bentonite mixture is clearly detected to measure a response of dielectric constant. In order to estimate an unsaturated permeable property of soil-bentonite mixtures, equations between volumetric water content and dielectric constant were derived from this study.

• Journal of the Korean Geotechnical Society
• /
• 제21권7호
• /
• pp.91-105
• /
• 2005

In this study, the deformation behavior of Daegok dam during the construction was analyzed based on the measurement data and a comparative analysis with foreign CFRD measurements was performed. From measuring settlements of Daegok dam with depth, overall behavior was evaluated to be consistent with measured data of other CFRD dams. In addition, construction modulus, void ratio and shape factor were also evaluated to be major factors in predicting the settlement behavior during construction of CFRD-typed dam from measured data of 38 CFRD-typed dams, and the maximum internal settlement is proportional to the void ratio. From the relationship between the maximum internal settlement and the height of a dam, 26 dams were assessed to have its relative modulus ranging between 0.001 and 0.01. In case of general CFRD, the average modulus of maximum internal settlement to the height of a dam is estimated to be 0.005. In case of a low void ratio, the construction modulus was high with its shape factor below 4. On the other hand, in case of a high void ratio, the relative settlement rate was high with its shape factor more than 4.

• Journal of the Korean Geotechnical Society
• /
• 제27권1호
• /
• pp.87-97
• /
• 2011

In this study, a new methodology by using the X-ray CT scan is proposed for estimating void ratio of sandy soil. The general problems in high resolution X-ray CT scan such as beam hardening and ring artifact had been successfully settled up using thin metal plate filter and some calibration process. In order to calculate the void ratio of sand from its CT image, the procedures and algorithm for CT image processing are developed. CT scan tests for Joomunjin sand are carried out to verify its applicability to void ratio testing.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제13권8호
• /
• pp.3713-3718
• /
• 2012

The relations of the various undrained geotechnical properties were, in depth, investigated for highly plastic soils using the numerous experimental testing results. The sensitivity is proportional to void ratio and OCR but inversely proportional to effective unit weight. The difference in Su(Un), Su(UU), and Su(FV) tends to increase or decrease with such sensitivity, void ratio, and OCR. The possibility of deducting the empirical equations denoting the correlations of various properties and the indicator for selecting appropriate testing method could be confirmed.

• Journal of the Korean Society of Propulsion Engineers
• /
• 제10권2호
• /
• pp.78-86
• /
• 2006

This paper presents the performance test result of the 30-ton class turbopump turbine. Test has been conducted using high pressure cold air, The turbine overall performance has been measured for various pressure ratio and rotational speed settings. The nozzle-rotor clearance effect on turbine performance also has been tested for the four kinds of the nozzle-rotor clearance values. We found that turbine efficiency rated 51.1% at its design velocity ratio and pressure ratio of 13.5. We also found that turbine efficiency can be increased by 3.5% for approximately 1mm decrement of the nozzle-rotor clearance from its nominal value.

• Journal of the Korean Geotechnical Society
• /
• 제23권11호
• /
• pp.39-48
• /
• 2007

The soil-water characteristic curve(SWCC) is a useful tool in the prediction of the engineering behavior of unsaturated soils. Several equations are available in the literature to mathematically represent the experimental behavior of the SWCC. Some equations are based on the assumption that the shape of curve is dependent upon pore-size distribution. Other equations assume that SWCC can be estimated from the grain size distribution and the physical properties of soils. This study evaluated the suitability of using two different SWCC equations for defining the relationship between water content and matric suction. Various parameters that influence the SWCC behavior are also briefly discussed.